-
1, 03-601553 Issue 1 February 2007 1 700431984 03-601553 Issue 1 February 2007 Quick Start for Hardware Installation: IG550 Integrated Gateway Preparing before you go on-site 1. Check Juniper software compatibility with TGM550 Gateway Module firmware. See http:// support.avaya.com. 2. Download the most recent firmware for the TM550. See http://support.avaya.com . 3. Ensure the customer has an FTP or TFTP server that is accessible to the TGM550. If not, download a TFTP server to your laptop. 4.…
-
2, 2 Quick Start for Hardware Installation: IG550 Integrated Gateway Installing hardware 1. If the customer has a four-post rack and is using a shelf, install the shelf according to manufacturer guidelines. If the customer is using the brackets supplied with the router, install the brackets on the chassis of the Juniper Services router midway between the front and back. 2. Install the router on the rack. 3. Be sure the …
-
3, Quick Start for Hardware Installation: IG550 Integrated Gateway 03-601553 Issue 1 February 2007 3 ! CAUTION: CAUTION: The Juniper Services Router must be turned off before inserting or removing the Avaya TGM550, TIM modules, or PIM modules. These modules are not hot-swappable. If you attempt to remove or insert these modules while the router is turned on, the router might reset or malfunction in some other way. 4. Insert the TGM550 and each TIM or PIM into the correc…
-
4, Avaya IG550 4 Quick Start for Hardware Installation: IG550 Integrated Gateway ● Ring-type, vinyl-insulated TV14-6R lug or equivalent to accommodate the 10 AWG cable. 8. Connect power to the back of the router. AC Power ● Insert the appliance coupler end of a power cord into the appliance inlet on the power supply faceplate. ● For a 6350 only, repeat for the second power supply. ● Insert the plug of each cord into an AC power source recepta…
-
5, Quick Start for Hardware Installation: IG550 Integrated Gateway 03-601553 Issue 1 February 2007 5 Loading Disk on Key, if available 1. If available, insert the Disk on Key (USB memory stick) into the USB port on the front of the router. The Disk on Key contains the configuration information. If a Disk on Key is not provided, go to Configuring the router using the CLI, if Disk on Key not available on page 7. 2. Press the power button to turn on the Juniper Services Router. 3. When the Power on LED lights steady green, remove the Disk on Key. T…
-
6, Avaya IG550 6 Quick Start for Hardware Installation: IG550 Integrated Gateway Connecting the LAN and your laptop after using Disk on Key 1. With an RJ-45 Ethernet cable, cable an Ethernet port (Eth 0) of the Juniper Services Router. 2. Connect your PC or laptop to the console port of the Juniper Services Router 3. Configure your laptop: ● Turn on the power to the management device. Start your asynchronous terminal emulation application (such as Microsoft Windows …
-
7, Quick Start for Hardware Installation: IG550 Integrated Gateway 03-601553 Issue 1 February 2007 7 ● Configure the port settings as follows: - Bits per second: 9600 - Data bits: 8 -Parity: None - Stop bits: 1 - Flow control: None Finish configuring the router after using Disk on Key 1. Connect the USB modem to one of the USB ports. 2. Log in to the router with the root login and password. If a password has not been established, leave the password field blank. 3. Upgrade the…
-
8, 8 Quick Start for Hardware Installation: IG550 Integrated Gateway 2. Connect your PC or laptop to the console port of the Juniper Services Router 3. Configure your laptop: ● Turn on the power to the management device. Start your asynchronous terminal emulation application (such as Microsoft Windows Hyperterminal) and select the appropriate COM port to use (for example, COM1). ● Configure the port settings as follows: - Bits per second: 9600 - Data bits: 8 -Parity: None - Stop bits: 1 - Flow co…
-
9, Quick Start for Hardware Installation: IG550 Integrated Gateway 03-601553 Issue 1 February 2007 9 6. At the cli prompt (>), type show interfaces ge-0/0/<x>, where <x> is the port that you are using, which can be 1, 2, or 3. 7. Check the Hardware address for the router port you are going to administer for Ethernet connections, for example ge-0/0/3. The Hardware address, which is also called the MAC address, in the example is 00:12:1e:a9:7a:00 . 8. At the cli prompt (>), enter configure. 9. At the configure pr…
-
10, 10 Quick Start for Hardware Installation: IG550 Integrated Gateway ● set interfaces vp-<slot_number>/0/0 unit 0 family inet address <internal_ip_address>/32 destination <tgm550_IP_address>, where <internal_ip_address> is the address the TGM550 uses to telnet to the router and <tgm550_IP_address> is the IP address for accessing the TGM550. ● set system name-server <IP_address> where <IP_address> is the address of a DNS server on the LAN/WAN. Repeat this command f…
-
11, Avaya IG550 Quick Start for Hardware Installation: IG550 Integrated Gateway 03-601553 Issue 1 February 2007 11 b. At the cli prompt (>), enter request tgm fpc <slot_number> media-gateway-controller [<IP_address1> <IP_address2> <IP_address3> <IP_address4>] where <slot_number> is the location of the TGM550, <IP_address1> is either the Processor Ethernet IP address of the primary media server (S8300, S8400, or S8500) o…
-
12, Avaya IG550 12 Quick Start for Hardware Installation: IG550 Integrated Gateway 5. Updating TGM550 firmware ● At the TGM550-00<super># prompt, type show boot bank to determine the non-active disk partition (bank). You copy the firmware to the non-active boot bank. ● At the TGM550-00<super># prompt, type one of the following commands, depending on whether the file resides on an FTP, or TFTP server: - copy [tftp or ftp] SW_image <bank> <filename> <server_ip_address> where <bank> is the bank that is the…
