-
70, GA-M61VME-S2 Motherboard - 70 - English Figure 13 Windows Setup Press F6 if you need to install a 3rd party SCSI or RAID driver. Figure 14 Windows Setup S=Specify Additional Device ENTER=Continue F3=Exit Setup could not determine the type of one or more mass storage devices installed in your system, or you have chosen to manually specify an adapter. Currently, Setup will load support for the following mass storage devices(s) <none&g…
-
20, AMD GA-M61VME-S2 GA-M61VME-S2 Motherboard - 20 - English 3/4) CPU_FAN / SYS_FAN (Cooler Fan Power Connector) The cooler fan power connector supplies a +12V power voltage via a 3-pin/4-pin (only for CPU_FAN) power connector and possesses a foolproof connection design. Most coolers are designed with color-coded power connector wires. A red power connector wire indicates a positive connection and requires a +12V power voltage. The black connector wire is the ground wire (GND). Remember to connect the CPU/system fan cable to the CPU_FAN/SYS_FAN c…
-
76, GA-M61VME-S2 Motherboard - 76 - English Setting Up 6-Channel Audio STEP 1 : After installation of the audio driver, you should find an Audio Manager icon in your system tray (you can also find the icon in Control Panel). Double- click the icon to open the Audio Control Panel. STEP 2: In the Audio Control Panel, click the Audio I/O tab. In the upper left list, click 6CH Speaker. STEP 3: Connect the 6-channel speakers to the audio jacks on the motherboard and the surround cabl…
-
59, Appendix- 59 - English Exploring the Q-Flash TM utility screen The Q-FlashBIOS utility screen consists of the following key components. Task menu for Q-Flash utility: Contains the names of three tasks. Blocking a task and pressing Enter key on your keyboard to enable execution of the task. Action bar: Contains the names of four actions needed to operate the Q-Flash utility. Pressing the buttons mentioned on your keyboards to perform these actions. Using the Q-Flash TM utility: This section tells you how to update B…
-
71, AMD GA-M61VME-S2 Appendix- 71 - English Step 3: If Setup correctly recognizes the driver in the floppy disk, a controller menu similar to Figure 15 below will appear. Use the ARROW keys to select NVIDIA RAID CLASS DRIVER (Figure 15) and press ENTER. Later, when a screen similar to Figure 16 appears, you must press S to select additional driver. The screen will return to previous screen as shown in Figure 15. Select NVIDIA nForce Storage Controller and press ENTER. Figure 15 Figure 16 Windows Setup S=Specify Addi…
-
30, GA-M61VME-S2 Motherboard - 30 - English <F12> : Boot Menu Select boot sequence for onboard (or add-on cards) device. Boot Menu == Select a Boot First device == KL:Move Enter:Accept ESC:Exit Floppy LS120 Hard Disk CDROM ZIP USB-FDD USB-ZIP USB-CDROM USB-HDD Legacy LAN Press <F12> to enter the Boot Menu and use < > or < > to select a device, then press enter to accept. Press <ESC> to e…
-
68, AMD GA-M61VME-S2 GA-M61VME-S2 Motherboard - 68 - English To read more information about the RAID array, press ENTER to enter the Array Detail screen (Figure 9), where you should see detailed information about RAID mode, disk block size, disk model name, and disk capacity, etc. Figure 9 Figure 8 After that, the Array List screen displaying the RAID array you created will appear (Figure 8). (Note: BBS stands for BIOS Boot Specification. This indicates that the boo…
-
1, GA-M61VME-S2 AMD Socket AM2 Processor Motherboard User's Manual Rev. 1001 12ME-M61VMES2-1001R * The WEEE marking on the product indicates this product must not be disposed of with user's other household waste and must be handed over to a designated collection point for the recycling of waste electrical and electronic equipment!! * The WEEE marking applies only in European Union's member states.
…
-
61, Appendix- 61 - English Method 2 : @BIOS TM Utility If you do not have a DOS startup disk, we recommend that you use the new @BIOS utility. @BIOS allows users to update their BIOS under Windows. Just select the desired @BIOS server to download the latest version of BIOS. 1. Methods and steps: I. Update BIOS through Internet a. Click "Internet Update" icon b. Click "Update New BIOS" icon c. Select @BIOS TM sever d. Select the exact model name on your motherboard e. System will automatically downloa…
-
73, Appendix- 73 - English 4-1-5 2- / 4- / 6- / 8- Channel Audio Introduction This motherboard comes with three audio jacks. To set up multi- channel surround sound, install an additional 5.1/7.1 surround cable (optional) and enable the feature through the audio driver. Installing the 5.1/7.1 Surround Cable (Optional) The 5.1/7.1 Surround Cable provides center/ subwoofer speaker out, rear speaker out, and side speaker out audio jacks. To set up multi-channel surround sou…
-
31, BIOS Setup- 31 - English Standard CMOS Features This setup page includes all the items in standard compatible BIOS. Advanced BIOS Features This setup page includes all the items of Award special enhanced features. Integrated Peripherals This setup page includes all onboard peripherals. Power Management Setup This setup page includes all the items of Green function features. PnP/PCI Configuration This setup page includes all the configurations of PCI & PnP ISA…
-
15, Hardware Installation- 15 - English Dual Channel Memory Configuration The GA-M61VME-S2 supports the Dual Channel Technology. After operating the Dual Channel Technology, the bandwidth of Memory Bus will double. Due to CPU limitation, if you wish to operate the Dual Channel Technology, follow the guidelines below: 1. Dual Channel mode will not be enabled if only one memory module is installed. 2. To enable Dual Channel mode with two memory modules (it is …
-
25, Hardware Installation- 25 - English 14) F_USB1 / F_USB2 / (Front USB Connectors) Be careful with the polarity of the front USB connector. Check the pin assignment carefully while you connect the front USB cable, incorrect connection between the cable and connector will make the device unable to work or even damage it. For optional front USB cable, please contact your local dealer. Pin No. Definition 1 Power (5V) 2 Power (5V) 3 USB DX- 4 USB Dy- 5 USB DX+ 6 USB Dy+ 7 GND 8 GND 9 No P…
-
22, GA-M61VME-S2 Motherboard - 22 - English 9) F_PANEL (Front Panel Jumper) Please connect the power LED, PC speaker, reset switch and power switch etc. of your chassis front panel to the F_PANEL connector according to the pin assignment below. 1 2 19 20 HD- HD+ RES+ RES- NC IDE Hard Disk Active LED Reset Switch SPEAK- MSG- MSG+ PW- PW+ Message LED/ Power/ Sleep LED Speaker Connector SPEAK+ Power Switch HD (IDE Hard Disk Active LED) Pin 1: LED anode(+) Pin 2: LED cathode(-) SPEAK (Speaker Connector) Pin 1…
-
11, AMD GA-M61VME-S2 Hardware Installation- 11 - English Rear Panel I/O 1 PS/2 keyboard port 1 PS/2 mouse port 1 parallel port 1 COMA port 1 VGA port 4 USB 2.0/1.1 ports 1 RJ-45 port 3 audio jacks (Line In / Line Out / MIC In) I/O Control IT8716 chip Hardware Monitor System voltage detection CPU / System temperature detection CPU / System fan speed detection System / CPU warning temperature CPU / System fan failure warning Supports CPU Smart Fan function (Note 4) BIOS 1 4 M…
-
35, BIOS Setup- 35 - English Init Display First This feature allows you to select the first initiation of the monitor display from which card when you install a PCI card and a PCI Express VGA card on the motherboard. PCI slot Set Init display first to PCI. (Default value) PEG Set Init display first to PCI Express VGA card. Onboard VGA Set Init display first to Onboard VGA. Frame Buffer Size 16M Set frame buffer size to 16M. 32M Set frame buffer size to 32M. 64M Set frame buffer size to 64M. (Default valu…
-
14, GA-M61VME-S2 Motherboard - 14 - English Before installing the memory modules, please comply with the following conditions: 1. Please make sure that the memory used is supported by the motherboard. It is recommended that memory of similar capacity, specifications and brand be used. 2. Before installing or removing memory modules, please make sure that the computer power is switched off to prevent hardware damage. 3. Memo…
-
56, GA-M61VME-S2 Motherboard - 56 - English Dual BIOS Utility Boot From......................................... Main Bios Main ROM Type/Size.............................SST 49LF003A 512K Backup ROM Type/Size.........................SST 49LF003A 512K Wide Range Protection Disable Boot From Main Bios Auto Recovery Enable Halt On Error Disable Copy Main ROM Data to Backup Load Default Settings Save Settings to CMOS Q-Flash Utility Lo…
-
72, AMD GA-M61VME-S2 GA-M61VME-S2 Motherboard - 72 - English After the SATA controller driver installation is completed, you can proceed with the Windows 2000/XP installation. Figure 18 WindowsXP Professional Setup Welcome to Setup. This port of the Setup program prepares Microsoft(R) Windows (R) XP to run on your computer. To set up Windows XP now, press ENTER. To repair a Windows XP installation using Recovery Console, press R. To quit Setup without installing Windows XP, press F3. Enter= Continue R=Repair F3=Exit (Note: Each time you add a n…
-
38, GA-M61VME-S2 Motherboard - 38 - English Onboard Serial Port 2 Auto BIOS will automatically setup the port 1 address. 3F8/IRQ4 Enable onboard Serial port 2 and address is 3F8/IRQ4. 2F8/IRQ3 Enable onboard Serial port 2 and address is 2F8/IRQ3. (Default value) 3E8/IRQ4 Enable onboard Serial port 2 and address is 3E8/IRQ4. 2E8/IRQ3 Enable onboard Serial port 2 and address is 2E8/IRQ3. Disabled Disable onboard Serial port 2. Onboard Parallel P…
-
40, AMD GA-M61VME-S2 GA-M61VME-S2 Motherboard - 40 - English Power On By Keyboard Disabled Disable this function. (Default value) Password Enter from 1 to 5 characters to set the Keyboard Power On Password. Any KEY Press any key to power on the system. Keyboard 98 If your keyboard has a "POWER Key" button, you can press the key to power on the system. KB Power ON Password When "Power On by Keyboard" set at Password, you can se…
-
75, AMD GA-M61VME-S2 Appendix- 75 - English STEP 3: Connect the 4-channel speakers to the audio jacks on the motherboard and the surround cable, a small window will pop up and ask you what type of equipment is connected. Choose a device depend- ing on the type of speaker connected (4-channel audio consists of Front Speaker Out (Line Out) and Rear Speaker Out) and then click OK. The 4- channel audio setup is completed. Setting Up 4-Channel Audio STEP 1 : After installation of the audio driver, you should find an Audio Manager icon in your system tray (yo…
