-
1, TM i MICROMAPPER ™ LAN Wiremap Checker Users Manual (English) November 2001, Rev. 2, 9/03 © 2001-2003 Fluke Corporation. All rights reserved. All product names are trademarks of their respective companies.
…
-
2, LIMITED WARRANTY AND LIMITATION OF LIABILITY Each Fluke Networks product is warranted to be free from defects in material and workmanship under normal use and service. The warranty period is one year and begins on the date of purchase. Parts, accessories, product repairs and services are warranted for 90 days. This war- ranty extends only to the original buyer or end-user customer of a Fluke Networks authorized reseller, and does not app…
-
3, i Table of Contents Title Page Introduction ....................................................................................................................1 Features .......................................................................................................................... 2 M ICROMAPPER Kit Content ................................................................................................ 2 Registration......................................................................................…
-
5, 1 MICROMAPPER™ Introduction Congratulations on your purchase of the M ICROMAPPER network cable tester! The M ICROMAPPER is a hand-held cable tester that enables network professionals to quickly and easily verify the integrity of Ethernet twisted pair cables. In one step, the M ICROMAPPER will test twisted pair cabling for opens, shorts, reversed, crossed, and split pairs. Simply slide the switch to the Cable position, press the (TEST) button and the M ICROMAPPER will automatically scan for any existin…
-
6, Fluke MicroMapper MicroMapper User’s Manual 2 Features • Tests for wiring faults and detects opens, shorts, crossed, reversed, and split pairs. (Split pair fault detection requires a minimum cable length of 15.75" (40cm)) • Verifies shield integrity • M ICROMAPPER’s Remote Identifier enables one person to test installed cabling • Easy to read fault display and high speed testing • Generation of two tones for tracing cables and locati…
-
7, MicroMapper™ Safety Information 3 Safety Information WWarnings Do not connect MICROMAPPER to a live circuit as it may damage the unit. Do not open the unit or attempt to repair in case of malfunction. Please send it back to your distributor for repair or replacement. Caution Strong radio frequency fields may cause inaccurate readings. Do not drop or get the unit wet. Do not expose MICROMAPPER to extreme humidity or direct sunlight. Contacting Fluke Networks www.flukenetworks.com [email protected] +1-425-446-4519 �…
-
8, Fluke MicroMapper MicroMapper User’s Manual 4 MICROMAPPER Controls and LEDs 1 - 23 - 64 - 57 - 8 SHIELD SHORT TONER TEST REVERSED MISWIRE SPLIT PAIRS LOW BATTERY REMOTE M ICRO M APPER atx02f.eps Figure 1. MICROMAPPER Network Cable Tester Table 1. M ICROMAPPER Controls and LEDs Item Number Description A Pair and Shield Indicator LEDs B Toner LED C TEST button D REMOTE Adapter with RJ45 Jack E RJ45 Jack F Off/Cable/Toner Switch G Fault LEDs H Low Battery LED
…
-
9, MicroMapper™ Battery 5 Battery MICROMAPPER requires four 1.5 AAA batteries. IEC : LR03. Others : AAA, E92, 4003; JIS : AM 4 ; ANSI : 24A; 1.5 Volt (nominal). atx03s.bmp The Battery LED will light up when MICROMAPPER detects a low battery condition. Using MICROMAPPER with a low battery may affect the test accuracy. If M ICROMAPPER is stored for more than a month, the battery should be removed. MICROMAPPER’s Toner Operation 1. Slide the switch on t…
-
10, Fluke MicroMapper MicroMapper User’s Manual 6 MICROMAPPER Tests 1. Slide the switch on the right side to the Cable position to turn M ICROMAPPER on. 2. Connect one end of the cable to be tested to the M ICROMAPPER’s RJ45 jack. 3. Connect the other end of the cable to the M ICROMAPPEr Remote’s RJ45 jack. 4. Press (TEST) to view the results. 5. The horizontal LEDs indicate the cable’s integrity status. • Green: Pair or Shield is good • Green flashing: Pair or Shield is f…
-
11, MicroMapper™ Fault Status 7 Fault Status SHORT TEST TONER SHORT REVERSED MISWIRE SPLIT PAIRS LOW BATTERY 1-2 3-6 4-5 7-8 SHIELD 1 2 3 6 4 5 7 8 1 2 3 6 4 5 7 8 SS OPEN 1 2 3 6 4 5 7 8 1 2 3 6 4 5 7 8 SS 1-2 3-6 4-5 7-8 SHIELD TEST TONER SHORT REVERSED MISWIRE SPLIT PAIRS LOW BATTERY
…
-
12, Fluke MicroMapper MicroMapper User’s Manual 8 REVERSED 1 2 3 6 4 5 7 8 S 1 2 3 6 4 5 7 8 S TEST TONER SHORT REVERSED MISWIRE SPLIT PAIRS LOW BATTERY 1-2 3-6 4-5 7-8 SHIELD MIS-WIRE TEST TONER SHORT REVERSED MISWIRE SPLIT PAIRS LOW BATTERY 1-2 3-6 4-5 7-8 SHIELD 1 2 3 6 4 5 7 8 S 1 2 3 6 4 5 7 8 S SPLIT PAIR TEST TONER SHORT REVERSED MISWIRE SPLIT PAIRS LOW BATTERY 1-2 3-6 4-5 7-8 SHIELD 1 2 3 6 4 5 7 8 S 1 2 3 6 4 5 7 8 S
…
-
13, MicroMapper™ 9 Technical Specifications Connectors M ICROMAPPER main unit: RJ45 jack Remote Identifier: RJ 45 jack Pairs tested 1-2, 3-6, 4-5, 7-8, and shield LED Display Horizontal: 5 green LEDs for pairs and shield display (1 - 2, 3 - 6, 4 - 5, 7 - 8, and SHIELD) Vertical: 6 red LEDs (TONER, SHORT, REVERSED, MISWIRE, SPLIT PAIRS, and LOW BATTERY) Cables test limit Minimum: 15.75" (40cm); Maximum: 656’ (200 m) Power IEC 86-1 (1996-07) --- Primary Batteries - General IEC 60086-2 (1997-07) --- Primary Batteri…
