Expobar G-10 Operation & User’s Manual

31, 31 G-10 R PROGRAMMING USING THE DISPLAY Auto On/Off Counters After accepting the changes made in the "Set clock" menu, pressing the 2 Short Espressos button accesses the coffee machine's Auto On/Off programming menu (see fig. 09). To change the Auto On/Off time, increase/decrease the values (hours) using the 1 Short Espresso and 1 Long Espresso buttons whilst the values are flashing. When the desired value is reached, press the 2 Sh…

19, Expobar G-10 19 G-10 R OPERATION The porta-filter set Inserting the porta-filter in the group Align the porta-filter's two lateral flanges with the slots in the group. Insert the porta-filter and rotate it anti-clockwise until the handle is perpendicular to the coffee machine. Porta-filter not fully inserted. Correct position. Group gasket is worn out, please replace. Lock-in spring (lter basket) Filter basket Placing porta…

11, 11 G-10 R Front view of the machine OVERVIEW OF COMPONENTS G-10 DISPLAY CONTROL 2GR Steam tap Hot water tap Display Digital temperature control Drink buttons Steam tap Steam wand Steam wand Hot water outlet Porta-lter Brewing group Heater element lamp ON/OFF switch …

34, Your Dealer TECHNICAL SUPPORT Contact your supplier For the warranty to be valid, the conditions for maintenance must have been followed in accordance with our instructions, proper care must have been taken and any claim against the warranty must be sent without delay. The equipment in question may not be used while awaiting service if there is any risk that the damage or defect would worsen. The warranty will not cover the consumption of supplies such as glassware, n…

8, 8 G-10 R SPECIFICATIONS MODEL G-10 DISPLAY CONTROL 2GR G-10 3 BOILERS DISPLAY CONTROL 2GR Steam wand 2 units 2 units Hot water outlet 1 unit 1 unit Temperature control PID regulation PID regulation Temperature control by group No Yes Programmed via display Yes Yes Dispensing system for tall cups Optional Optional Energy saving mode Yes Yes Height, width, depth (mm) 530, 680, 590 530, 680, 590 Boiler volume (l) 11.5 11.5 + 1.5 + 1.5 Power supply 230V 1N~ 3330 W 50/60 Hz 230V 1N~ 3330 W 50/60 …

15, 15 G-10 R DIMENSION SKETCH G-10 DISPLAY CONTROL 3GR A C D B Model A B C D G-10 3GR 530 mm 980 mm 590 mm 74 mm G-10 3GR Tall Cup 530 mm 980 mm 590 mm 124 mm G-10 3Gr Boilers 530 mm 980 mm 590 mm 74 mm G-10 3Gr 4 Boilers Tall Cup 530 mm 980 mm 590 mm 124 mm …

12, 12 G-10 R Front view of the machine OVERVIEW OF COMPONENTS G-10 DISPLAY CONTROL 3GR Steam tap Hot water tap Display Digital temperature control Drink buttons Steam tap Steam wand Hot water outlet Porta-lter Brewing group Heater element lamp Steam wand ON/OFF switch …

26, 26 G-10 R CLEANING AND CARE Additional handling of the machine Remove and insert the porta-filter gently. Never use excessive force to try to close the porta-filter. STORAGE AND DISPOSAL OF MACHINE How to store the machine Disposal of machine Make all the cleaning procedures described in this manual. Disconnect and roll up the power cord. (this should be performed by a qualied person). Disconnect the inlet hose from the machi…

22, Expobar G-10 22 G-10 R OPERATION Dispensing hot water Place a jug (or similar) under the hot water outlet. Open the hot water tap. Once the machine has dispensed the desired amount of water, close the hot water tap. WARNING! Never expose hands and ngers directly under the water outlet during operation to avoid scalding or serious burns. …

33, 33 G-10 R TROUBLESHOOTING Coffee-grinding problems Coffee dispensing is very fast: The coffee grinding is to coarse. Adjust the coffee- grinding setting. Coffee dispensing is very slow: The coffee grinding is to fine. Adjust the coffee- grinding setting. Problem Possible cause Solution The machine does not start up The plug is not correctly inserted into the power socket Check that the plug is correctly inserted and that the power socket is operational. The circuit…

28, 28 G-10 R PROGRAMMING Programming the coffee dosage This section explains how to program the doses dispensed automatically by the drink buttons. Note: Programming any of the options on the left-hand drink buttons (when viewing the machine from the front) automatically sets the dispensing volumes on all of the other drink buttons. This only applies to the left-hand drink buttons. Programming other drink buttons only modies th…

32, 32 G-10 R MESSAGES AND ALARMS Fault in flow meter X / Flow fault detected in counter X Flow meter Gr. X Check that the machine is receiving water. Time-out alarm Boiler filling up Temperature sensor fault Probe unconnect Service the machine. To disable the alarm and reset the counter: Turn off the machine. Simultaneously press and hold down the 1 Short Espresso and 1 Long Espresso buttons. Turn o…

16, 16 G-10 R Positioning Install the machine on a level surface. Adjust the feet to ensure that it dispenses coffee evenly in all of the cups. Select a level, dry, strong and stable installation surface at least 110 cm off the floor. Leave enough space above and behind the machine to ensure easy cleaning and maintenance. Do not install the machine whilst wet or damp. If wet or damp, leave the machine until completely dry then ask service personn…

21, 21 G-10 R OPERATION Steaming and frothing milk Place the steam wand over the drip tray and open the steam tap for a few seconds, this will allow condensed water to be ejected. Close the steam tap when only steam comes out. Immerse the steam wand into the jug containing the milk, make sure the wand tip is submerged. Open the tap again to start heating or frothing the milk. Once the milk reaches the desired temperature, close the tap and remove the jug…

24, 24 G-10 R CLEANING AND CARE Cleaning the Brewing group and porta-filter WARNING! Never try to remove the porta-lter whilst the group is in cleaning operation, as the pressurized hot water could cause scalding or serious injury. Once cleaning has nished, wait about 3 seconds before removing the porta-lter. Unlock and remove the porta-lter from the group head. Place the cleaning membrane in the lter basket. Fill the lter basket …

9, Expobar G-10 9 G-10 R G-10 DISPLAY CONTROL 3GR TECHNICAL SPECIFICATIONS SPECIFICATIONS MODEL G-10 DISPLAY CONTROL 3GR G-10 4 BOILERS DISPLAY CONTROL 3GR Steam wand 2 units 2 units Hot water outlet 1 unit 1 unit Temperature control PID regulation PID regulation Temperature control by group No Yes Programmed via display Yes Yes Dispensing system for tall cups Optional Optional Energy saving mode Yes Yes Height, width, depth (mm) 530, 980, 590 530, 980, 590…

2, Expobar G-10 2 G-10 R CONTENTS Original Instructions CONTENTS .............................................................................................................................................................................2 SYMBOL DESCRIPTION ..................................................................................................................................................4 Hazard intensity levels .................................................................…

6, 6 G-10 R Intended use Do not remove or disable any of the mechanical, electrical or thermal protection mechanisms. In case of emergency, (e.g. the machine catches fire or becomes unusually hot or noisy), disconnect the power immediately and close the water inlet tap. If the machine is not going to be used for a prolonged period of time, disconnect the power. When disconnecting the power, pull the…