-
21, 21 One-Year Replacement Warranty & Guarantee A one-year worldwide replacement guarantee covering HDanywhere™ electronic devices is provided by HD Connectivity. You can use our freepost returns service to send your faulty device back to us (UK only). If you need to use this guarantee contact HDanywhere™ Customer Services: [email protected] / 0844 351 0190 Warranty Details If your HDanywhere product does not work properly because of a defect in materials or …
-
2, 2 Contents 4x2 HDBaseT Hybrid Matrix Contents pg.3 Introduction pg.4 Out the box pg.5 Package Contents System Features Before you start pg.6 HDBaseT Wiring Guidance What is the best type of cable to use? Shielded cables Best Practice HDBaseT with patch panels & wall plates Connection termination pg.7 Disable “CEC” Power Down Central Hub pg.8 Front Panel Rea…
-
5, 5 Out the box The package contains all of the necessary components for a full install. Package Contents Matrix central hub unit DC48V/500mA central hub power supply, figure8 lead + in-line pack Multiroom+PoE Display Receiver module (no power supply required) Matrix IR remote control 4 x IR TX cables (IR emitter/blaster) 1 x IR over HDMI Receiver dongle 3 x IR RX ‘magic eye’ cables (from 30KHz to 56KHz IR receiver) 1 for Matrix unit IR extension System Features ● 2 HDTV location multiroom HD system ● 4 HDMI i…
-
19, 19 Specifications Operating Temperature Range -15 to +55°C (5 to 131 °F) Operating Humidity Range 5 to 90 % RH (no condensation) Input Video Signal 5.0 volts p-p Input DDC Signal 5 volts p-p (TTL) Video Format Supported DTV/HDTV; 1080p/1080i/720p/576p/4 80p/576i/480i, VESA formats All 3D formats inc 3D over HDMI 1080p60 4K x 2K Up to 48-Bit Deep Colour Audio Format Supported Dolby-HD, DTS-HD, up to 7.1 Channel Output Video HDMI 1.4a + HD…
-
13, 13 Powering your system on for the first time The very first power on/initialisation of the system is crucial to its future operation and performance. The central hub incorporates a small memory. This memory stores the initial handshake negotiations and authentications between all the connected sources and HDTVs in order to aid faster switching times between the connected source devices thereon after. ● Power the HDTVs on at the mains. Bring out of standby mode and select the correct H…
-
7, HDanywhere HKM42BTP 7 Connection termination Terminate the cabling using RJ45 connectors to the 568B wiring standard (shown below). IMPORTANT: Local building regulations may apply to the installation of cabling in properties. Please ensure that these are checked and followed in accordance with the laws of your territory. Disable “CEC” Ensure that any manufacturer HDMI link or CEC protocols such as Samsung Anynet Link, Sony Bravia Link, Panasonic Viera Link etc are switched to �…
-
16, 16 Operating your Matrix Manually You can operate HDMI source switching manually by using the buttons situated on the Matrix unit front panel. Simply press the button that corresponds to the output that you wish to change HDMI source on and toggle through until the desired HDMI input source video is being displayed. A numerical LED indicates which HDMI source input is being shown on each output (HDTV). Remote Control operation Included with the system is a small Remote Control (shown). This can operat…
-
8, HDanywhere HKM42BTP 8 Central Hub The central hub is the heart of the HDanywhere system. Front Panel ● Power on / off switch ● Source IR emitter cable connection ports (to control source 1-2-3-4) ● Forward IR cable connection ports (to send IR to TV receiver 1-2-3-4) ● TV Receiver status indicator lights (TV locations 1-2-3-4) ● Source status indicator lights (Inputs 1-2-3-4) ● Central Hub IR extension cable port ● IR receiving window…
-
10, 10 First time setup Your HDanywhere™ system is designed so that you can set it up quickly and start using it right away. Please note that the HDanywhere™ product warranty does not cover damage due to electrical disturbances. If possible safeguard your equipment by connecting all provided power supplies to an electrical surge suppressor / line conditioner. Before you connect up your system, please ensure that you complete the following: ● Ensure that any manufacturer HDMI link, HDMI control…
-
12, HDanywhere HKM42BTP 12 High Speed Internet Connectivity This feature of your HDanywhere system comes in response to the popular emergence of on-demand Internet services (such as BBC iPlayer, online gaming, and social networking) on Smart TVs. Each HDanywhere+ TV Receiver has 2 x 10/100 Ethernet ports available that allow a wired connection of devices requiring a high speed connection to the Internet. To enable the high speed internet connectivity function of the HDanywhere system, simply connect one of the Ethernet output ports of your br…
-
11, 11 IR setup If you need troubleshooting or background advice on IR, please go to www.hdconnectivity.com/support where you can reference our up to date IR support pages. Step 1 - Central Hub IR cable set-up Connect the IR TX emitter cables to the 3.5mm jack ports labelled IR TX 1, 2, 3, 4 on the front panel and position the IR emitter “bud” on the front of the source, over the IR receiving window on each of the corresponding co…
-
17, HDanywhere HKM42BTP 17 Troubleshooting Should you encounter a problem when using your matrix a soft (power cycle) or hard reset of the unit should resolve most issues. A separate troubleshooting info sheet may be available for more complex issues. If you do not resolve your issue after reading this, email [email protected] with as much information about your set-up and the symptoms as possible. To perform the hard reset please see below. To perform a soft reset: Simple press the…
-
20, 20 Product Registration Registering helps us to support HDanywhere™ users most effectively and makes the process more efficient should you ever require technical support. By registering you are also ensuring that you are notified of and receive the most up-to-date firmware updates as soon as they are released. The process is quick and easy. Please visit www.HDanywhere.com/register to register your product purchase. Not registering will not affect your replacement warranty or product guarantee. Privacy: Al…
-
23, HDanywhere HKM42BTP 23 HDanywhere™ and the HDTV emblem are trademarks of HD Connectivity Ltd. HDMI, the HDMI Logo are trademarks of HDMI Licensing LLC. The details in this manual are correct at the time of going to print. The specification and features are subject to change without notice. HD Connectivity. 23 Link Business Centre, Malvern, Worcestershire WR14 1UQ.
…
-
6, 6 Before you start For the most up-to-date installation best practice advice, please visit: http://www.hdconnectivity.com/support http://www.hdconnectivity.com/support HDBaseT Wiring Guidance HDanywhere Multiroom+ PoE SingleWire systems require a single network cable to be run from each HDTV location, back to a central location. ‘SingleWire‘ systems use HDBaseT technology to transmit over 1 x Cat5e/6/7 cable up to a 100 metre distance. What is the best type of cable to use? Currently you can use Cat5e, Cat6, Cat6e, Cat6a, Cat7 or Cat…
-
1, HDanywhere HKM42BTP 1 4x2 HDBaseT Hybrid Matrix with SingleWire HDBaseT® Technology Watch. Control. Enjoy. HDanywhere™ from HD Connectivity follow @HDConnectivity on Twitter or HDanywhere on Facebook Connect up to 4 x HDMI sources (Satellite/Cable HD Receivers, Blu-Ray players, Media Servers, Games Consoles, CCTV etc) and realise the potential of full HD 1080p High Definition picture and sound quality on up to 2 x HDTVs around the home. Please r…
-
9, 9 TV Receiver Front Panel 1. HDCP indictor light – shows whether a handshake between that display and source has been authenticated 2. Link indicator light – confirms the TV receiver is connected to the hub 3. Mode indicator light – if flashing all is correct 4. Power indicator light – Lit when the TV receiver is on 5. IR receiver cable connection port – For use with the IR passback system for control of your sources 6. IR emitter cable connection port – For use with the IR forward system from…
-
15, 15 Audio Outputs The Hybrid matrix has separate digital and analogue audio outputs so the HDMI audio can also be enjoyed via older sound systems. The audio track routed via the separate audio outputs corresponds with what HDMI input is selected on TV output 1. (NB both video and audio remain on both HDMI outputs 1 and 2, the audio is not stripped from the HDMI signal). Important: The audio format is dependent on the EDID reported by the HDMI output 1 display device. Most…
-
14, 14 Completing your set-up After completing the process above, all HDTVs should be displaying the selected HDMI source device video and audio.
…
