-
11, 11 / 41 Hakki Pilke 35 Falcon Translation Version 10 4. Turn the upper section of the con- veyor into the operating position using handle B (Figure 4b). 5. Turn transport position support bar C on the out-feed conveyor belt (Figure 4c) to the side. 6. Use a winch to lift the conveyor to the desired angle (max 40°) and lock the upper section of the out- feed conveyor to the operating position using l…
-
5, 5 / 41 Hakki Pilke 35 Falcon Translation Version 10 1.4. Operating conditions The temperature range within which the machine can be operated is -20 to +30°C. In the winter, the op- erator must ensure that there is no risk of slipping in the working area. The working area must be level and clear of unnecessary items. No unauthorised persons are allowed to enter the working area. The machine may only be used in sufficient lighting conditions. These require- ments must be met for the entire duration of the work. The mach…
-
13, 13 / 41 Hakki Pilke 35 Falcon Translation Version 10 Electrically powered model An electrically powered machine func- tions with a power of 7.5 kW. The IP rat- ing of the electric motor is 55. The fuse must be a min. 16 A type D fuse. The electrical cable must be at least 5 x 4 mm², and it is connected to the socket in the electric motor (Figure 6). The firewood processor can be activated with the green starter button on the front section of the machine. Use the r…
-
9, 9 / 41 Hakki Pilke 35 Falcon Translation Version 10 2.3. Arranging the machine for operation and transport Before arranging the machine for operation and using it, ensure that the operating conditions, detailed in Section 1.4, are met and review the safety instructions in Section 1.5. Note! Inspect and clean the machine before setting it up for transport! Placing the in-feed conveyor in the operating or transportation position Place the in-feed …
-
28, 28 / 41 Hakki Pilke 35 Falcon Translation Version 10 4.8. Changing the oil Change the hydraulic oil of the fire- wood processor as follows (Figure 23 and Figure 24): 1. Shut the machine down and disconnect it from its power sources. 2. Open filler cap A of the hy- draulic oil tank (this will al- low the oil to drain more easily). 3. Open drain plug B and drain the oil into a suitable con- tainer. 4. Open the cover of hydr…
-
7, Hakki Pilke 35 Falcon 7 / 41 Hakki Pilke 35 Falcon Translation Version 10 The danger zone around the ma- chine is 10 metres. Risk of crushing The maximum permitted angle of the conveyor is 40°. Do not walk under the conveyor. The maximum speed for the cardan shaft is 500 rpm. The rotation direction is in the direction of the arrow. Hydraulic oil Saw chain oil Danger zone Lubrication point
…
-
38, Hakki Pilke 35 Falcon 38 / 41 Hakki Pilke 35 Falcon Translation Version 10 5. Failures and remedial measures 5.1. Cause-effect table for failures and their removal Failure Cause Remedial measure The splitting force is insufficient to split the log. 1. The log is in an incorrect position or the splitting blade is at the wrong height. 2. The previous log has jammed on the splitting blade. 3. The machine has overheated or the oil quality is poor. 4. Other fault 1. Open the cage and correct the log position or adjust the sp…
-
6, Hakki Pilke 35 Falcon 6 / 41 Hakki Pilke 35 Falcon Translation Version 10 1.7. Warning symbols Read the machine’s manual before operating the machine. Wear eye and ear protection. Wear safety footwear and work gloves. Do not wear any loose items or clothing. Always grab the piece of wood or log from the side. Lifting point for a forklift. Beware of moving parts. Beware of the cardan shaft. Beware …
-
25, 25 / 41 Hakki Pilke 35 Falcon Translation Version 10 Figure 19 4.6. Out-feed conveyor belt adjustment and cleaning out-feed conveyor The tightness and alignment of the out-feed conveyor’s belt can be adjusted using nuts A in Figure 20 (2 pcs). Loosen adjustment nut A on the side to which you wish the belt to run. Do not tighten the belt excessively to prevent the spring being compressed. …
-
1, 1 / 41 Hakki Pilke 35 Falcon Translation Version 10 Hakki Pilke Falcon 35 FIREWOOD PROCESSOR – Instructions for assembly, operation and maintenance – EC Declaration of Conformity – Safety instructions – Guarantee terms MAASELÄN KONE OY Valimotie 1, FI-85800 Haapajärvi tel.+358 (0)8 7727300, [email protected] www.hakkipilke.fi ENGLISH The operator must read and understand these instructions before operating the machine!
…
-
16, 16 / 41 Hakki Pilke 35 Falcon Translation Version 10 3. Operating the machine 3.1. Controls and functions of the machine Figure 11 Names and functions of the controls (Figure 11): A. Splitting cylinder control lever - Pushing the lever to the left returns the splitting cylinder to the initial position. - Pushing the lever to the right makes the splitting cylinder perform the splitting motion. B. Control valve for an auxiliary device, such as a log lifter, (accessory) C. Log press handle. …
-
35, Hakki Pilke 35 Falcon 35 / 41 Hakki Pilke 35 Falcon Translation Version 10 4.13. Solenoid and pressure regulating valves The pressure regulating valves are adjusted to the correct settings at the factory. The firewood processor's guarantee is void if the factory settings are changed. If you need to change the settings for any reason, first contact the manufacturer or retailer and follow their instructions carefully. Changing the cartridge settings in- correct…
-
23, 23 / 41 Hakki Pilke 35 Falcon Translation Version 10 4.3. Height adjustment of the splitting blade The splitting blade can be controlled mechanically by moving control lever F (Figure 11 and 20) up or down. The splitting blade can be lifted by moving lever F to the left and vice versa. Logs should always be as centred as pos- sible when passing the blade in order to keep the size of the firewood consistent. Figure 16 (The splitting blade is detachable on the left and locked on the right) T…
-
3, 3 / 41 Hakki Pilke 35 Falcon Translation Version 10 4.13. Solenoid and pressure regulating valves................................................................................................ 35 4.14. Washing and cleaning ............................................................................................................................ 37 4.15. Storage ..................................................…
-
21, 21 / 41 Hakki Pilke 35 Falcon Translation Version 10 Figure 13 If the conveyor is jammed for any reason, its running speed must be set to zero and the machine must be shut down before removing the cause. There must be at least 50 cm between the end of the out-feed conveyor and the pile of processed firewood. Note! The operator must ensure that the distance between the debris discharge opening and the pile of debris that accumulates under it is at least 20 cm. 3.7.…
-
15, 15 / 41 Hakki Pilke 35 Falcon Translation Version 10 2.6. Additional hydraulics connections (accessories) Using the quick couplings of the additional hydraulics Connect the additional hydraulics (HakkiLift log lifter or HakkiFeed log table separator) by inserting the hydraulic hos- es of the accessory into quick couplings A (red) and B (black) (Figure 9). Use the quick couplings with control lever B (Figure 11). Note! Only connect off…
-
27, 27 / 41 Hakki Pilke 35 Falcon Translation Version 10 Replacing the saw bar Replace the saw bar as follows (Figure 22Virhe. Viitteen lähdettä ei löytynyt.): 1. Remove the saw chain according to steps 1–5 of Section 4.7 “Re- placing and tightening the saw chain”. 2. Remove flange bolts (2 pcs) and remove the flange fastening plate A. 3. Remove the saw bar from the groove. 4. Place the new flange against gear wheel B, twist it into the groove and l…
-
40, Hakki Pilke 35 Falcon 40 / 41 Hakki Pilke 35 Falcon Translation Version 10 7. Guarantee terms We offer a guarantee on our machines, with the following conditions: 1. This guarantee covers defects caused by manufacturing or material failures, except for defects in compo- nents that are classified as parts that will sustain wear and tear. 2. The guarantee is valid for the original buyer for one (1) year, starting from the day of purchase, but for no more than 1,000 operating hours. 3. The guarantee becomes…
-
37, 37 / 41 Hakki Pilke 35 Falcon Translation Version 10 4.14. Washing and cleaning Any loose dirt and sawdust can be removed from the machine with pressurised air, for example. The machine can also be washed with a high-pressure washer as long as the water jet is not aimed directly at the bearings or elec- trical equipment. Always ensure that the machine and the working area are sufficiently clean during operation. The machine must always be cleaned after use. Clean the machine at …
-
20, Hakki Pilke 35 Falcon 20 / 41 Hakki Pilke 35 Falcon Translation Version 10 Re-splitting or splitting without cutting 1. Raise the protective cover of the cutting and splitting channel. 2. Place the log you want to split in the splitting groove. 3. Close the cutting/splitting guard. 4. Activate the splitting using lever A (Figure 11). The above procedure can be used to split wood without cutting it, as necessary. 3.6. Usin…
