-
1, 1 / 14 Hakki Feed 472 Translation Version 1 HakkiFeed 472 Log table – Operating and maintenance instructions – EC Declaration of Conformity – Safety instructions – Guarantee terms - List of spare parts MAASELÄN KONE OY Valimotie 1, FI-85800 Haapajärvi, Finland Tel. +358 (0)8 772 7300 [email protected] www.hakkipilke.fi ENGLISH The operator must read and understand these instructions before operating the machine!
…
-
2, 2 / 14 Hakki Feed 472 Translation Version 1 Table of contents 1. General information ..................................................................................................................... 3 1.1. Introduction .............................................................................................................................................. 3 1.2. Purpose of use ........…
-
3, Hakki Pilke HakkiFeed 472 3 / 14 Hakki Feed 472 Translation Version 1 1. General information 1.1. Introduction The purpose of this manual is to ensure that the machine is used in the manner intended by the manufacturer, taking safety into consideration. Everyone operating the machine or working in close proximity to it must study this manual carefully. Before commencing work, operators must also familiarise themselves with the machine's control…
-
4, 4 / 14 Hakki Feed 472 Translation Version 1 The operator must ensure that the use of the device does not cause danger to others and that there are no unauthorised persons in the danger zone. The machine may not be operated while under the influence of alcohol or other drugs, or when tired. The machine may not be operated unless the operator has familiarised themselves with this instruction manual. The machine is only intend…
-
5, 5 / 14 Hakki Feed 472 Translation Version 1 2.4. Main components of the machine Hakki Feed 472 is a hydraulically controlled accessory for the Hakki Pilke firewood processor. It is controlled hydraulically with the operating levers of the Hakki Pilke firewood processor’s control unit. A. In-feed conveyor B. Chain conveyor C. Dispenser stoppers D. Dispenser Figure 2. Main components of the machine 3. Co…
-
6, Hakki Pilke HakkiFeed 472 6 / 14 Hakki Feed 472 Translation Version 1 3.1.1. Connecting the hydraulics Use the operator’s manual of the relevant Hakki Pilke firewood processor for the connections! Use of the table requires two separate control valves: Example Figure 3. In-feed conveyor A (Figure 2) - Connected in series to the Hakki Pilke firewood processor’s in-feed system (quick couplings C (red) and D (black)) Note! If the machine feature…
-
7, 7 / 14 Hakki Feed 472 Translation Version 1 4. Operating the machine 4.1. Performing a test run on the machine The machine may not be used before a test run has been performed and all the functions of the machine have been tested. Both the test run and testing can only be performed by a person who has studied the machine’s manual. Before the test run, all of the components of the firewood processor must be checked. If any faults or wear and tear that may affect the safe use o…
-
8, 8 / 14 Hakki Feed 472 Translation Version 1 5. Machine maintenance The machine must be disconnected from its power source before any maintenance, adjustment, replacement or cleaning measures. Only use spare parts that are supplied by the manufacturer or your retailer. If the guards of the machine have to be removed for maintenance, they must always be reattached before the machine is activated. After maintenance and adjustment measures, a …
-
9, 9 / 14 Hakki Feed 472 Translation Version 1 Figure 5 (tightening the motor chain) 5.2. Lubrication The machine has 21 lubrication points in total, presented in the figures below. 1. Chain conveyor (A) chains 3 pcs, dispenser stoppers (A) 3 pcs, Figure 6: A, B (every 50 hours) 2. Chain conveyor motor chain 1 pc (under the guard), Figure 7 (every 100 hours) 3. Nipples of the chain conveyor dispenser bearings 6 pcs, Figure 6: D (every 200 hours) 4. Nipples …
-
10, 10 / 14 Hakki Feed 472 Translation Version 1 Washing and cleaning Loose debris and sawdust can be cleaned from the machine with pressurised air, for example. The machine can also be washed with a high-pressure washer as long as the water jet is not aimed directly at the bearings. Always ensure that the machine and the working area are sufficiently clean during operation. The machine must always be cleaned after use. Clean the machine at su…
-
11, 11 / 14 Hakki Feed 472 Translation Version 1 9. Spare part images 9.1. Main assembly figure
…
-
12, Hakki Pilke HakkiFeed 472 12 / 14 Hakki Feed 472 Translation Version 1 9.2. Main assembly parts list No. Number Name qty 1 48001 Cross conveyor 1 2 48002 Conveyor frame, left 1 3 48100 Conveyor frame, right 2 4 48028 Intermediate support 5 5 48009 Roller attachment rear, left 1 6 48014 Roller attachment rear, right 2 7 48044 Rear stop pipe 3 8 48015 H…
-
13, 13 / 14 Hakki Feed 472 Translation Version 1 10. Guarantee terms The guarantee is valid for the original buyer for 12 months, starting from the date of purchase, but for no more than 1,000 operating hours. In guarantee matters, always contact the machine’s seller before undertaking any procedures. A guarantee claim must be issued to the seller in writing immediately upon discovery of a defect. If the defect concerns a damaged part or component, please sen…
-
14, 14 / 14 Hakki Feed 472 Translation Version 1 11. Declaration of incorporation for partly completed machinery (Machinery Directive 2006/42/EC, Annex II B) Manufacturer: Maaselän Kone Oy Address: Valimotie 1, FI-85800 Haapajärvi Name and address of the person who is authorised to compile the technical file: Name: Timo Jussila Address: Valimotie 1, FI-85800 Haapajärvi The aforementioned person assures t…
