-
21, 19 J. Install safety device (See Fig. 28 & Fig. 29). Fig. 28 Powerside safety device Fig. 29 Offside safety device
…
-
39, AMGO HS-10 37 50-7 10206069 0 ring 1 1 50-8 10203080 Support Ring 1 1 50-9 10410087 Y ring OSI 1 1 50-10 11217302 Piston 1 1 50-11 10410087 Y ring OSI 1 1 50-12 10203080 Support ring 1 1 50-13 11217311 Bore weldment 1 1 50-14 11217303 Piston rod 1 1 50-15 10206071 nut 1 1 Parts For Hydraulic Second Cylinder 50A-1 11217279 Head Cap 1 1 50A-2 10201035 O ring 1 1 50A-2A 10217298 Dust …
-
18, 16 H. Install overhead top beam 1. With help of the hook of top beam, put one side of top beam on top of the extension column and connecting the top beam to extension column by bolts, tighten the bolts. Then assemble the connecting bracket (See Fig. 25). Fig. 25 Hook on to the extension columns Tighten the bolts
…
-
28, 26 M. Install electrical system Connect the power source on the data plate of Power Unit. Note: 1. For the safety of operators, the earth wire must contact the floor well. 2. Pay attention to the direction of rotations when using three phase motors. Single phase motor (See Fig. 39). 1. Connecting the two power supply wire (active wire L and neutral wire N) to terminals #6, #2 of AC contactor respe…
-
38, 36 69 11217050 Main Lock Pin 2 2 70 10217051 Fixing Screw 2 2 71 10217066 Hex bolt 2 2 72 10217008 Spring 1 1 73 11217031 Offside Cam Lock 1 1 74 10217033 Tighten nut 1 1 75 10217064 Safety cable L=7900mm 1 0 10217064A Safety cable L=9120mm 0 1 76 10217232 Oil hose5/16＂*9300mm 1 0 10217240 Oil hose5/16＂*10520mm 0 1 76A 10217233 Oil hose5/16＂*1430mm 1 1 76B 10217234 Oil hose 5/1…
-
16, 14 3. When the ceiling height is lower than 167-1/4”, connecting the extension columns with the upper holes. (See Fig.23). Fig. 23 Low Setting(HS-10H)
…
-
7, AMGO HS-10 5 B. SPECIFICATIONS OF CONCRETE (See Fig. 6) Specifications of concrete must be adhered to the specification as following. Failure to do so may result in lift and/or vehicle falling. 1. Concrete must be thickness 4” minimum and without reinforcing steel bars, and must be completely dry before lift installation. 2. Concrete must be in good condition and must be of test strength 3,000psi minimum. 3. Floors must be level with no cracks or holes. …
-
40, 38 Revision day:08/2018 16 81400365 O Ring 1 1 17 10209152 Tie kit 1 1 18 81400267 Magnet 1 1 19 81400290 Filter 1 1 20 81400413 Motor 1 1 21 10420070 Push button 1 1 22 4103…
-
23, 21 L. Install power unit (See Fig. 31) 201 Fig. 31
…
-
34, 32 To lift vehicle 1. Keep clean of site around the lift 2. Position lifting arms to the lowest position 3. Shorten the arms to the shortest condition 4. Open the lifting arms to allow vehicle drive in 5. Position vehicle between columns 6. Move/adjust 4 arms so that lifting pads are under correct lift points (per manufacturer’s recommendation) of vehicle. Adjust pads so that all four pads will c…
-
22, 20 K. Raise the carriages up by hand and make them be locked at the same level (See Fig. 30). Fig. 30
…
-
9, 7 4. Lift the lower column with a fork lift or hoist, take down the package stand, than take off the lower extension column, take out the parts in the inner column (See Fig. 11). 5. Move aside the parts and check the parts according to the shipment parts list . Open the carton of parts and check the parts according to parts box list (See Fig. 12, Fig.13). 6. Check the parts of the parts bag 1 according …
-
17, 15 G. Position columns Position the columns on the installation layout of base plate. Check the columns vertical with level bar, and adjusting with the shims if the columns are not vertical. Do not tighten the anchor bolts (See Fig.24). Note: Minimum embedment of Anchors is 3-1/2”. 30/90 Width between columns:110-1/4” Adjusting with the shims Overall…
-
6, 4 II. INSTALLATION REQUIREMENT A. TOOLS REQUIRED Rotary Hammer Drill (3/4”) Hammer Level Bar English Spanner (12") Ratchet Spanner With Socket (28 # ) Wrench set Carpenter’s Chalk Screw Sets Tape Measure (295”) Pliers Socket …
-
3, 1 I. PRODUCT FEATURES AND SPECIFICATIONS CLEAR-FLOOR DIRECT-DRIVED MODEL FEATURES Model HS-10 HS-10H (See Fig. 1) · Direct-drived design, minimize the lift wear parts and breakdown ratio · Dual hydraulic cylinders, high standards, utilizing NOK oil seal in cylinder · Self- lubricating UHMW Polyethylene sliders and bronze bush · Single-point safety release with dual safety design . Clear-floor design, provide unobstructed floor use . Overhead safety shut-off device prevents v…
-
25, 23 J. Install safety cable. Install safety cable from offside safety assy. firstly, pass through the top beam, then install to power side safety assy. (See Fig. 33). Fig. 33 Safety cable pass through small pulley bracket Install safety cable from offside safety assy. firstly Finally, safety cable connected with the power side s…
-
32, AMGO HS-10 30 Lifting the carriages and lock at the same height, strain the safety cable and then release a little, and then tighten the cable nuts. Make sure the safety device can always be worked properly. 2. Synchronization The Synchronization adopts hydraulic equalization system. A. Turn the reversing handle to the position as Fig.47, push button UP, raise the power side carriage to the highest position, then turn …
