-
33, 31 Illustration of hydraulic valve for power unit Fig.43 Check valve Oil outlet Oil return port Release valve Handle for relief valve Relief valve Throttle valve
…
-
8, 6 6.2 PRO-14A, PRO-14AE 7. Open the carton of parts and check the parts according to the parts box list (See Fig. 12). Fig. 12 Fig.11
…
-
6, AMGO PRO-14 4 III. STEPS OF INSTALLATION A. Location of Installation Check and insure the installation location (concrete, layout, space size etc.) is suitable for lift installation. B. Check the Parts Before Assembly 1, The equipment should be unload and transfer by forklift. (See Fig.6) 2. Packaged lift and Hydraulic Power Unit (See Fig. 7). 3. Open the outer packing carefully (See Fig. 8). Fig. 6 Fig. 6 Ship…
-
22, AMGO PRO-14 20 5. Install oil-water separator and manual control air valve. (see Fig.33) 6. Connecting air inlet (Air supply pressure 5kg/cm 2 - 8kg/cm 2 ), adjusting the air pressure of Oil-water separator to 0.8MPa (See Fig. 34). Fig. 34 Clockwise to increase the air pressure Counter-clockwise to reduce the air pressure …
-
15, 13 I. Assembly offside platform and slider block. check the vertical of columns with level bar, adjusting with the shims if the columns are not vertical, and then tighten the anchor bolts (See Fig. 24). Note: The tightening torque for the anchor bolt is 150N.m 8 18 Install the slider block 3-15 3-16 3-14 Using the ratchet spanner with socket to …
-
21, 19 M. Install air-line system 1. Connecting front and rear Cross Beam cylinders by using 6*4 black air line. (the actual length of air line can be cut by user) (See Fig.30) 2. Cut the 6*4 black air line by scissor between two retainer, then connect the air line with T fitting. (See Fig. 31). 3. Connecting the solenoid valve using 6*4 black air line (the actual length of air line can be cut by user) (See Fig. 32). …
-
23, AMGO PRO-14 21 N. Install Electrical System Connect the power source on the data plate of Motor. Note: 1. For the safety of operators, the power wiring must contact the floor well. 2. Pay attention to the direction of rotations when using 380V, three phase motors. Single phase motor (See Fig. 35). 1. Connecting the two power supply lines (fire wire L and zero wire N) to terminals of AC contactor marked L1, L2 respectively. 2. Connecting the two motor wires to terminals of AC contactor marked T1, T2. 3. Connecting A2 of AC cont…
-
4, AMGO PRO-14 2 MODEL SPECIFICATIONS Model Lifting Capacity Lifting Height Liftin g Time Overall Length (Inc. Ramps) Overall Width Width Betw een Colu mns Motor PRO-14 14000LBS 73-1/2” 60S 257-1/2” 130-7/8” 116” 2.0HP PRO-14A 14000LBS 75-3/8” 60S 257” 130-7/8” 116” 2.0HP PRO-14E 14000LBS 73-1/2” 81S 286” 130-7/8” 116” 2.0HP PRO-14AE 14000LBS 75-3/8” 81S 285-1/2” 130-7/8” 116” 2.0HP II. INSTALLATION REQUIREM…
-
20, 18 L. Install Hydraulic System (See Fig. 29). Note: Oil hoses connected to oil cylinder must be passed above the cable, cylinder inlet port must swing upward to avoid the oil hose and oil return pipe scratched by cable. Oil hose and air line pass through the retainer 76 70 69 Protective ring cyli…
-
7, 5 4. Take off the Drive-thru Ramps and Columns (See Fig. 9). 5. Loose the screws of the upper package stand, take off the offside platform, take out the parts inside the power-side platform, than remove the package stand. 6. Move aside the parts and check the parts according to the shipment parts list (See Fig. 10,Fig.11). 6.1 PRO-14,PRO-14E Fig. 9 Fig.10
…
-
35, 33 VI. OPERATION INSTRUCTIONS To lift vehicle 1. Keep clean of environment near the lift; 2. Drive vehicle to the Platform and put on the brake; 3. Turn on the power and press the push button, raise the lift to the working position; Note: make sure the vehicle is steady when the lift is raised. 4. Press the Handle of release valve to lock the lift in the safety position. Make sure the Safety device is locked at the same height. To lower vehicle …
-
16, 14 J. Install cables (See Fig. 25). 1. Pass through the cables from the platform to the columns according to the number of the cables. No. Cable ○ 1 ○ 2 ○ 3 ○ 4 Length PRO-14(A) (inc.…
-
17, AMGO PRO-14 15 2. The cable pass through the cross beam to top plate of columns and be screwed with cable nuts (See Fig. 26). Cable pass through between the big pulley and tension pulley 83 Cable pass through top plate and be screwed with cable nuts. Fig. 26 Install limit pin Cable 48 Pulley 47 Limit Pin
…
-
29, AMGO PRO-14 27 3 81 82 10460092 0 0 1 1 76A 10460013 Black Air Line 1 1 0 0 Item Part# Description PRO- 14 PRO-14A PRO- 14E PRO- 14AE 76A 10460094 Black Air Line 0 0 1 1 77 10420167A Black Air Line 1 1 1 1 78 11480033 Turnplate adjusting block 0 4 0 4 79 11480045 Turnplate adjusting block 0 4 0 4 80 11440082 Turnplate adjusting block 0 4 0 4 81 11476635 Pulley 4 4 4 4 82 10476024 Washer for P…
-
19, 17 K. Install Oil-water separator, Manual control air valve and Power unit (See Fig. 28). Item Part# Description QTY 20 10420145 Oil-water separator AFR-2000 1 21 10420146 Straight Fitting for air line 1 22 10209009 Cup Head Bolt 8 23 10420076 Fitting 1 24 10420159 Straight Fitting 1 25 11420160 Fixing plate of Manual Control Valve 1 26 10420161 Self locking nut 2 27 10420162 Manual Control Air Valve 1 28 …
-
5, 3 B. Equipment storage and installation requirements. The equipment should be stored or installed in a shady, normal temperature, ventilated and dry place. C. SPECIFICATIONS OF CONCRETE (See Fig. 5) Specifications of concrete must be adhered to the specification as following. Failure to do so may result in lift and/or vehicle falling. 1. Concrete must be thickness 7-…
-
31, 29 55-9 10460052 Y- Ring 1 55-10 11460053 Piston 1 4.3 POWER UNIT EXPLODED VIEW（071102） Fig.42 220V/60Hz Single Phase
…
-
10, 8 C. Use a carpenter’s chalk line to establish installation layout as per Table 1 Make sure the size is right and base is flat (see Fig. 14). Note: Reserve space front and behind the installation site. Model A B C PRO-14,PRO-14A 216 1/2” 130 7/8” 253” PRO-14E、PRO-14AE 245” 130-7/8” 277-7/8” Fig. 14 Use a carpent…
-
30, 28 3-13 10420046 Split Pin 8 3-14 10420042 Plastic Slider 16 Item Part# Description Qty Note 3-15 10209033 Washer 40 3-16 10420043 Socket Bolt 32 3-17 10420175 Slack-cable safety lock (left & right ) Each 2 3-18 10420171 Pin 8 3-19 10420172 Pin Bush For Slack-cable safety lock 8 3-20 10206019 Snap Ring 16…
-
25, AMGO PRO-14 23 IV. EXPLODED VIEW Model PRO-14, PRO-14E 1 2 3 8 18 44 203 32 12 54 55 56 57 45 Fig.38 4
…
-
36, 34 VIII. TROUBLE SHOOTING IX. LIFT DISPOSAL: When the car lift cannot meet the requirements for normal use and needs to be disposed, it should follow local laws and regulations. TROUBLE CAUSE REMEDY Motor does not run 1. Start Button does not work 2.Wiring connections are not in good condition 3. Motor burned out 4. AC contactor burned out 5. Height limit switch is damaged 1.Replace start button 2.Repair all wiring connections 3.Repair…
-
18, 16 3. Illustration for platform cables (See Fig. 27). Limit slider Fig. 27 Hex Bolt M10*150 cable ④ cable ② 19 cable ① cable ② cable ④ cable ② cable ③ cable ④ cable ④ cable ② cable ② cable ① cable ④ cable ③ Limit block
…
