AMGO 409-P Installation And Service Manual

2, CONTENTS Product Features and Specifications ..................................................... 1 Installation Requirement ……………………………………………………………………………… 2 Steps of Installation …........................................................................ 3 Exploded View ................................................................................. 26 Test Run ……….........…

28, AMGO 409-P 26 CROSS BEAM 3 1 201 3 4 7 9 12 13 15 14 11 10 5 6 8 62 2 Fig. 37 …

6, 4 3. Take off the drive-in ramps and columns (See Fig.6 ). 4. Loose the screws of the upper package stand, take off the offside platform, take out the parts inside the powerside platform, then remove the package stand. 5. Move aside the parts and check the parts according to the shipment parts list (See Fig. 7). 6. Open the carton of parts and check the parts a…

24, AMGO 409-P 22 According to the below diagram screw up the M16*30 bolts, then attach the drive- in ramp. O. Install Rear wheel stop plates (See Fig. 33) After driving the vehicle on the lift, take off the drive-in ramp, install rear wheel Fig. 29 Screw the M16*30 bolts to the side hole of the cross beam Attach the drive-in ramp with the bolts 63 7 65 65A …

37, AMGO 409-P 35 56 410036 Protective hose 1 1 57 209145A Cup head bolt with washer 8 8 Item Part# Description Qty Note 409-P 409-HP 58 410029 Plastic cover for cross beam 4 4 59 410030 Spring 4 4 60 420033 Spring 4 4 61 410501 Parts box 1 0 410502 0 1 62 420239 Limit block 1 1 63 410094 Rear wheel stop plate 2 2 64 410101 Layer board assy for drive in ramp 2…

25, 23 stop plates to the drive-in ramp position. P. Install Layer Board Assy. for Drive in Ramp Take down the Drive in Ramp, and put it in the platform and layer board assy.(See Fig. 31) For optional kits installation. 1. Install optional caster kits (See Fig. 32) Fig. 30 64 Fig. 31 …

23, 21 a. The source wires (L1, L2, L3) are connected with terminals of AC contactor marked L1, L2, L3 respectively. b. Terminals 4# of control button is connected with terminals of AC contactor marked L1; wire 3# is connected with A1 terminals of control button. M. Install spring and safety cover of cross beam (See Fig. 28). N. Install drive-in ramp, jack tray and plastic oil pans (See Fig. 29). …

11, 9 E. Put the cross beams at the same height and lock on the safety ladder (See Fig. 15). F. Install power side platform. This height for four threaded rod of safety ladders should be the same. Safety ladder pass through the hole of the top plate, then tighten the two nuts Fig. 14 Fig. 15 18 17 The lifting cross beam height should be fitted for installing the platform and its part…

33, AMGO 409-P 31 To lift vehicle 1. Keep clean of environment near the lift. 2. Drive vehicle to the platform and put on the brake. 3. Take off the drive-in ramp, install rear wheel stop plates to the drive-in ramp position. 4. Turn on the power and press the control button, raise the lift to the working position. Note: make sure the vehicle is steady when the lift is raised. 5. Press the release valve handle to lock the lift in the safety position. Make sure the safety device is loc…

20, 18 2. Install Power unit on the cross beam B (See Fig.24). Car in direction Fig. 24 Cross beam B 40 41 40 Fixing plate GUDI 42 Install M8*25 Socket bolt with washer to these two holes. …

16, 14 2. The cable goes through the cross beam to top plate of columns and be screwed with cable nuts (See Fig. 20). Fig. 20 Cable goes between the big pulley and tension pulley Cable pass through top plate and be screwed with cable nuts. 17 …

35, AMGO 409-P 33 IX. PARTS LIST FOR MODEL 409-P 409-HP Item Part# Description Qty. Note 409-P 409-HP 1 410001 Power-side Column 1 0 410074 0 1 2 410002 Offside Column 3 0 410075 0 3 3 410050 Cross Beam A 1 1 4 410051 Offside Platform 1 0 410076 0 1 5 410052 Powerside Platform 1 0 410077 0 1 6 410053 Cross Beam B 1 1 7 410007 Drive-in ramp 2 2 8 209043 Hex …

7, 5 (See Fig. 8). 7. Check the parts of the parts bag according to the parts bag list (See Fig. 9). B. Use a carpenter’s chalk line to establish installation layout as per Table 1 Fig. 8 Fig. 9 …

21, 19 K. Install Hydraulic System 1. For power unit attached to the column of cross beam A (See Fig. 25) Note: Oil hoses connected to oil cylinder must be passed above the cable to avoid the oil hose scratched by cable. 2. For power unit attached to the column of cross beam B (See Fig. 26). a d cylinder inlet port swing upward Oil return hose passed above the cable b 53 Fig. 25 52 The oil …

39, 37 12 81400294 Gear Pump 1 1 13 10209034 Relief Valve 1 1 Item Part# Description Qty. Note 409-P 409-HP 14 81400295 Spring Washer 2 2 15 81400365 Hex Screw 2 2 16 10209152 O-Ring 1 1 17 85090167 Ties 1 1 18 81400290 Magnet of power units 1 1 19 81400412 Filter 1 1 20 81400088 Motor 1 1 21 10420070 Push Button 1 1 22 81400463 Socket Bolt 1 1 23 81400287 O-Ring 1 1 …

27, 25 2. Using the prescribed rotary hammer drill, and drill all the anchor holes and install the anchor bolts. Do not tighten the anchor bolts (See Fig. 36). Note: The tightening torque for the anchor bolt is 150N.m ,Anchor bolts driven into the ground at least 90mm IV. EXPLODED VIEW Model 409-P/409-HP Fig. 36 Drillin g Clearin g Expand 90mm Nut Fig. 35 69 …

13, 11 2. Install tire stop plate with bolts and washer on the platform: Tighten the platform on cross beam B with bolts, tighten the tire stop plate on cross beam A with bolts Note: The bolts for the side with tire stop plate is longer, pay attention when choosing the bolts (See Fig.17) Instruction: 1)This lift is designed in both side (cross beam A and cross beam B) car in direction, user can install the lift according to the location. Below is the installation for the side of cross beam B car in direction. If ch…

30, 28 Illustration of hydraulic valve Manual hydraulic power unit 110V.60Hz,single phase(Fig. 41) Fig.43 Fig. 40 …

22, AMGO 409-P 20 Note: The oil return hose can be adjusted when installation L. Install Electrical System Connect the power source on the data plate of Power Unit. Note: For the safety of operators, the power wiring must connect the floor well. Single phase motor (See Fig.27). 1. Connecting the two power supply lines (fire wire L and zero wire N) to terminals of AC contactor marked L1, L2 respectively. 2. Connecting the two motor wires …

18, 16 I. Install connecting bar for safety device and release handle (See Fig. 22). View B Cross beam B Cross beam A View A 22 44 Connecting bar Pass through the connecting bar from the safety lock rotated device assy. of cross beam A/B Safety lock rotated Device assy. Connecting bar 43 43A 45A 45 Safety lock rotated Device assy. Fig. 22 According to the a…

15, 13 H. Illustration for cable installation 1. Pass through the cables from the platform to the columns according to the number of the cables (See Fig. 19). NO. Cable ① ② ③ ④ Length for 409-P (inc. connecting fitting) 124” 363 1/4” 187” 301 3/8” Length for 409-HP (inc. connecting fitting) 132 3/4” …

14, 12 G. Install offside platform and plastic block, then install the bolts for the platform strengthen plate, check the plumbness of columns with level and adjusting with the shims (See Fig. 18). Fig. 18 Level bar Install the bolts for the platform strengthen plate 33 9 10 32 Note: DO NOT completely tighten the limit slide blocks. Loosen 1/4 lap after tightening. 4 29 30 31…

3, 1 4-POST MODEL 409-P 409-HP FEATURES · Single point manual safety release. · Four mechanical locking devices, each equipped with both primary and secondly safety locks. · Power-side column can be installed at both side, front or rear. · Non-skid diamond platforms and adjustable safety lock ladders. · Optional kits: Rolling jack with hand pump, caster kits. MODEL 409-P 409-HP SPECIFICATIONS Model Lifting Capacity Lifting Height Liftin…

29, AMGO 409-P 27 CYLINDERS Manual power unit 220V,60Hz Fig.38 Fig. 39 …