-
52, Administration: File Management System Files 35 Cisco Small Business 300 Series Managed Switch Administration Guide 4 Configuration files on the device are defined by their type, and contain the settings and parameter values for the device. When a configuration is referenced on the device, it is referenced by its configuration file type (such as Startup Configuration or Running Configuration), as opposed to a file name that can be modified by the user. Content can be copied f…
-
279, IP Configuration IPv4 Management and Interfaces Cisco Small Business 300 Series Managed Switch Administration Guide 262 16 • Status—Whether the entry was manually entered or dynamically learned. STEP 4 Click Add. STEP 5 Enter the parameters: • IP Version—The IP address format supported by the host. Only IPv4 is supported. • VLAN—In Layer 2, displays the management VLAN ID. For devices in Layer 2 mode, there is only one directly-connected IP subnet, which is always in the management VLAN. All the static and dynamic addr…
-
36, Status and Statistics Managing RMON 19 Cisco Small Business 300 Series Managed Switch Administration Guide 2 • Late collision event has not been detected. • Received (Rx) error event has not been detected. • Packet has a valid CRC. To view RMON statistics and/or set the refresh rate: STEP 1 Click Status and Statistics > RMON > Statistics. STEP 2 Select the Interface for which Ethernet statistics are to be displayed. STEP 3 Select the R…
-
247, Cisco Small Business 300 Spanning Tree Defining MSTP Interface Settings Cisco Small Business 300 Series Managed Switch Administration Guide 230 13 STEP 5 Enter the parameters. • Instance ID—Select the MST instance to be configured. • Interface—Select the interface for which the MSTI settings are to be defined. • Interface Priority—Set the port priority for the specified interface and MST instance. • Path Cost—Set the port contribution to the root pa…
-
413, Cisco Small Business 300 21 Cisco Small Business 300 Series Managed Switch Administration Guide 396 Access Control The Access Control List (ACL) feature is part of the security mechanism. ACL definitions serve as one of the mechanisms to define traffic flows that are given a specific Quality of Service (QoS). For more information see Quality of Service. ACLs enable network managers to define patterns (filter and actions) for ingress traffic. Packets, entering the device on a port or LAG with an active ACL, are either admitted or denied entry. This section conta…
-
177, Cisco Small Business 300 Smartport Configuring Smartport Using The Web-based Interface Cisco Small Business 300 Series Managed Switch Administration Guide 160 10 STEP 3 Click Apply. This sets the global Smartport parameters on the device. Smartport Type Settings Use the Smartport Type Settings page to edit the Smartport Type settings and view the Macro Source. By default, each Smartport type is associated with a pair of built-in Smartport macros. See Smartport T…
-
451, Quality of Service QoS Advanced Mode Cisco Small Business 300 Series Managed Switch Administration Guide 434 22 Defining Class Mapping A Class Map defines a traffic flow with ACLs (Access Control Lists). A MAC ACL, IP ACL, and IPv6 ACL can be combined into a class map. Class maps are configured to match packet criteria on a match-all or match-any basis. They are matched to packets on a first-fit basis, meaning that the action associated with the first-…
-
59, Cisco Small Business 300 Administration: File Management Download/Backup Configuration/Log Cisco Small Business 300 Series Managed Switch Administration Guide 42 4 • Restoring configuration files from an external device to the device. When restoring a configuration file to the Running Configuration, the imported file adds any configuration commands that did not exist in the old file and overwrites any parameter values in the existing configuration commands. When restoring a c…
-
313, IP Configuration IPv6 Management and Interfaces Cisco Small Business 300 Series Managed Switch Administration Guide 296 16 - Static —The entry was manually configured by a user. DHCPv6 Relay DHCPv6 Relay is used for relaying DHCPv6 messages to DHCPv6 servers. It is defined in RFC 3315. When the DHCPv6 client is not directly connected to the DHCPv6 server, a DHCPv6 relay agent (the device) to which this DHCPv6 client is directly- connected encapsulates the received messages from the directly-connected DHCPv6 client, and forwards them to the …
-
195, Cisco Small Business 300 Port Management: PoE PoE on the Device Cisco Small Business 300 Series Managed Switch Administration Guide 178 11 You can decide the following: • Maximum power a PSE is allowed to supply to a PD • During device operation, to change the mode from Class Power Limit to Port Limit and vice versa. The power values per port that were configured for the Port Limit mode are retained. NOTE Changing the mode from Class Limit to Port limit and vice versa when the device is operational forces the Powered Devi…
-
250, Managing MAC Address Tables Configuring Static MAC Addresses 233 Cisco Small Business 300 Series Managed Switch Administration Guide 14 Configuring Static MAC Addresses Static MAC addresses are assigned to a specific physical interface and VLAN on the device. If that address is detected on another interface, it is ignored, and is not written to the address table. To define a static address: STEP 1 Click MAC Address Tables &g…
-
315, Cisco Small Business 300 IP Configuration Domain Name Cisco Small Business 300 Series Managed Switch Administration Guide 298 16 As a DNS client, the device resolves domain names to IP addresses through the use of one or more configured DNS servers. DNS Settings Use the DNS Settings page to enable the DNS feature, configure the DNS servers and set the default domain used by the device. STEP 1 Click IP Configuration > Domain Name > DNS Settings. STEP 2 Enter the parameters. • DNS—Select to designate the device as a…
-
13, Cisco Small Business 300 Series Managed Switch Administration Guide 12 Contents SSD Default Read Mode Session Override 366 SSD Properties 366 Passphrase 367 Default and User-defined Passphrases 367 Local Passphrase 367 Configuration File Passphrase Control 368 Configuration File Integrity Control 368 Read Mode 369 Configuration Files 369 File SSD Indicator 369 SSD Control Block 370 Startup Configuration File 370 Running Configuration File 371 Backup and Mirror Configuratio…
-
225, VLAN Management Voice VLAN Cisco Small Business 300 Series Managed Switch Administration Guide 208 12 • Voice VLAN ID—The identifier of the current voice VLAN. • CoS/802.1p—The advertised or configured CoS/802.1p values that are used by the LLDP-MED as a voice network policy. • DSCP—The advertised or configured DSCP values that are used by the LLDP-MED as a voice network policy. • Best Local Source—Displays whether this voice VLAN was used by the device. The f…
-
87, Cisco Small Business 300 Administration: General Information Traceroute Cisco Small Business 300 Series Managed Switch Administration Guide 70 5 A page appears showing the Round Trip Time (RTT) and status for each trip in the fields: • Index—Displays the number of the hop. • Host—Displays a stop along the route to the destination. • Round Trip Time (1-3)—Displays the round trip time in (ms) for the first through third frame and the status of …
-
78, Administration: General Information Console Settings (Autobaud Rate Support) 61 Cisco Small Business 300 Series Managed Switch Administration Guide 5 • Host Name—Select the host name of this device. This is used in the prompt of CLI commands: - Use Default—The default hostname (System Name) of these switches is: switch123456, where 123456 represents the last three bytes of the device MAC address in hex format. - User Defined—Enter the …
-
383, Security: Secure Sensitive Data Management SSD Properties Cisco Small Business 300 Series Managed Switch Administration Guide 366 18 The default rules can be modified, but they cannot be deleted. If the SSD default rules have been changed, they can be restored. SSD Default Read Mode Session Override The system contains sensitive data in a session, as either encrypted or plaintext, based on the read permission and the default read mode of the user. The default read mode can be temporarily overridden as long it does not conflict with the SSD read …
-
459, Quality of Service Managing QoS Statistics Cisco Small Business 300 Series Managed Switch Administration Guide 442 22 Viewing Aggregated Policer Statistics To view aggregated policer statistics: STEP 1 Click Quality of Service > QoS Statistics > Aggregate Policer Statistics. This page displays the following fields: • Aggregate Policer Name—Policer on which statistics are based. • In-profile bytes—Number of in-profile packets that were received. • Out-of-profile bytes—Number of out-of-profile packets that were received. STEP …
-
79, Administration: General Information Rebooting the Device Cisco Small Business 300 Series Managed Switch Administration Guide 62 5 After Auto Detection is enabled in the Console Settings page, it can be activated by connecting the console to the device and press the Enter key twice. The device detects the baud rate automatically. To enable Auto Detection or to manually set the baud rate of the console: STEP 1 Click Administration > Console Settings. STEP 2 Select one of the following: • Auto Detect…
-
309, IP Configuration IPv6 Management and Interfaces Cisco Small Business 300 Series Managed Switch Administration Guide 292 16 In Layer 3 system mode, click IP Configuration > IPv6 Management and Interfaces > IPv6 Default Router List. This page displays the following fields for each default router: • Default Router IPv6 Address—Link local IP address of the default router. • Interface—Outgoing IPv6 interface where…
-
201, 12 Cisco Small Business 300 Series Managed Switch Administration Guide 184 VLAN Management This section covers the following topics: • VLANs • Configuring Default VLAN Settings • Creating VLANs • Configuring VLAN Interface Settings • Defining VLAN Membership • GVRP Settings • VLAN Groups • Voice VLAN • Access Port Multicast TV VLAN • Customer Port Multicast TV VLAN VLANs A VLAN is a logical group of ports that enables devices associated with it to communicate with each other over the Ethernet MAC layer, regardless of the physi…
-
97, Administration: Time Settings Configuring System Time Cisco Small Business 300 Series Managed Switch Administration Guide 80 6 Configuring the SNTP Mode The device can be in active and/or passive mode (see SNTP Modes for more information). To enable receiving SNTP packets from all servers on the subnet and/or to enable transmitting time requests to SNTP servers: STEP 1 Click Administration > Time Settings > SNTP Multicast/Anycast. STEP 2 Select from the following op…
-
1, Cisco Small Business 300 Series Managed Switch Administration Guide Release 1.3 ADMINISTRATION GUIDE
…
-
18, 1 Cisco Small Business 300 Series Managed Switch Administration Guide 1 Getting Started This section provides an introduction to the web-based configuration utility, and covers the following topics: • Starting the Web-based Configuration Utility • Quick Start Device Configuration • Interface Naming Conventions • Window Navigation Starting the Web-based Configuration Utility This section describes how to navigate the web-based switch configuration utility. If you …
-
183, Smartport Built-in Smartport Macros Cisco Small Business 300 Series Managed Switch Administration Guide 166 10 # smartport storm-control broadcast level 10 smartport storm-control include-multicast smartport storm-control broadcast enable # spanning-tree portfast # @ no_printer [no_printer] #macro description No printer # no switchport access vlan no switchport mode # no port security no port security mode # no smartport storm-control broadcast e…
-
179, Smartport Configuring Smartport Using The Web-based Interface Cisco Small Business 300 Series Managed Switch Administration Guide 162 10 corrections have been made prior to clicking Reapply. See the workflow area in Common Smartport Tasks section for troubleshooting tips. • Reapply a Smartport macro to an interface. In some circumstances, you may want to reapply a Smartport macro so that the configuration at an interface is up to date. For instance, reapplying a switch Smartport macro at a device interfa…
-
353, Cisco Small Business 300 Security Configuring 802.1X Cisco Small Business 300 Series Managed Switch Administration Guide 336 17 • Authentication Method—Select the authentication method for the port. The options are: - 802.1X Only—802.1X authentication is the only authentication method performed on the port. - MAC Only—Port is authenticated based on the supplicant MAC address. Only 8 MAC-based authentications can be used on the port. - 802.1X and MAC—…
-
5, Cisco Small Business 300 Series Managed Switch Administration Guide 4 Contents Displaying LLDP Neighbors Information 108 Accessing LLDP Statistics 112 LLDP Overloading 113 Configuring CDP 115 Setting CDP Properties 115 Editing CDP Interface Settings 118 Displaying CDP Local Information 119 Displaying CDP Neighbors Information 121 Viewing CDP Statistics 123 Chapter 9: Port Management 124 Configuring Ports 124 Setting Port Configuration 125 Co…
-
216, VLAN Management Voice VLAN 199 Cisco Small Business 300 Series Managed Switch Administration Guide 12 From a VLAN perspective, the above models operate in both VLAN-aware and VLAN-unaware environments. In the VLAN-aware environment, the voice VLAN is one of the many VLANs configured in an installation. The VLAN-unaware scenario is equivalent to a VLAN-aware environment with only one VLAN. The device always operates as a VLAN-aware switch. The device supports a single voice VLAN…
