-
23, 21 V. TEST RUN 1. Adjust the lower speed (See Fig.33) Users can adjust the descending speed according to their needs. Adjust the throttle valve core clockwise. At this time, the descending speed becomes slower, and vice versa. Clockwise to decrease the down speed Counterclockwise to increase the down speed Fig.33 Throttle valve Throttle valve
…
-
22, 20 220V 60Hz manual power unit breakdown list Item Part# Description QTY Item Part# Description QTY 1 81400180 Rubber pad 2 21 41030055 AC connector 1 2 81400130 Start capacitor 1 22 81400287 Cover of Motor Terminal Box 1 3 81400088 Running capacitor 1 23 71111104 AMGO Sticker 1 4 10420148 Screw, Washer 4 24 81400560 Throttle valve 1 5 81400066 Cover of capacitor 2 25 81400266 Relief valve 1 6 81400363 Motor connecting shaft 1 26…
-
20, 18 Item Part# Description QTY Item Part# Description QTY 1 11207027 Piston Rod 1 8 11207029 Adjustment Tube Cylinder 1 2 11207028 Piston 1 9 10217078 Dust Ring 1 3 10206069 O-Ring 1 10 10520058 O-Ring 1 4 10620053 Support Ring 1 11 11207030 Head Cap 1 5 10620054 Y-Ring 1 12 10201034 silencer 1 6 10630027 O-ring 1 13 10207031 O-Ring 1 7 10206071 Hex Nut 1 14 11207032 Cylinder Tube 1 4.5 Chain Pulley Support Assy. （ 11207681 ） exploded view ： Item Part# Description QTY 1…
-
5, 3 II. INSTALLATION REQUIREMENT A. TOOLS REQUIRED Rotary Hammer Drill(Φ19) Carpenter’s Chalk Hammer Screw sets Level Bar Tape Measure(7.5mm) English Spanner(12″) Pliers Wrench set：(10 ＃ 、13 ＃ 、14 ＃ 、12 ＃ Socket Head Wrench：(4 ＃ 、5 ＃ 、6 ＃ ) 17 ＃ 、19 # 、24 ＃ 、30 ＃ ) Fig.3
…
-
25, 23 8. Turn on the power and push the button , raise the lift until the rubber pad full contact the car and ensure it’s safe. 9. Continue raise the vehicle to the desired height and make sure the vehicle is steady when the lift is rising, then release the button. 10. Press the pressure relief handle of the hydraulic station and lower the lift to the safety lock position. Only after confirming that the safety device is in a normal working state before car maintaining. Note: In order to extend the service life of the cy…
-
10, AMGO SL-6 8 3. Fix column to the base plate. (See Fig.12) 4. Fix lifting platform to carriage. (See Fig.13) 23 30 25 26 27 27 26 50 49 Fig. 12 Fig. 13
…
-
11, AMGO SL-6 9 E. Install safety device, power unit, oil hose and wire holder (See Fig.14) Note: Tighten the oil hose fitting and power unit fitting to avoid oil leakage; Pay attention to the direction of power unit fitting. Fig.14 Tighter the screw with 19# wrench set after install power unit fitting. 67 4 9 12 17 14 15 16 18 5 68 13
…
-
2, CONTENTS I. PRODUCT FEATURES AND SPECIFICATIONS ............................................................................................... 1 II. INSTALLATION REQUIREMENT ....................................................................................................................... 3 III. STEPS OF INSTALLATION ................................................................................................................................ 5 IV. EXPLODED VIEW ................................…
-
14, 12 I. Tighten all the hydraulic fittings, and fill the reservoir with hydraulic oil. Note: In consideration of Hydraulic Power Unit’s durability and keep the equipment running in the perfect condition, please use Hydraulic Oil 46#. J. Using level to measure and adjust the column to be vertical. K. Fix the anchor bolts 1. Prepare the anchor bolts (See Fig. 22). 2. Using the prescribed rotary hammer drill, and drill all the anchor holes and…
-
16, 14 PARTS LIST FOR SL-6 Item Part# Description QTY. Note 1 11101013 Top Plate assembly 1 2 10206023 Self-Locking Nut M12 4 3 10217069 Hex Bolt 4 4 10209009 Cap Head Bolt 6 5 10209012 （φ3.2）Spring Pin 1 6 11203002 Power Side Safety Device 1 7 10209007 Safety Spring 1 8 11209008 Safety Cover 1 9 11217048 wire clip 2 10 11206002 Safety stop pin 1 11 10206003A Rubber handle sleeve 1 12 11203013 Coupling 1 13 81513019 Power unit 1 14…
-
3, AMGO SL-6 1 I. PRODUCT FEATURES AND SPECIFICATIONS CHAIN-DRIVE SINGLE POST MODEL SL-6 FEATURES · Compact design. · Hydraulic cylinders, designed and made on ANSI standard, utilizing NOK oil seal in cylinder. · Self-lubricating UHMW Polyethylene sliders and bronze bush. · Manual release safety lock, two-stage lock system · Super-symmetric arms design with 3-stages front arms and 2-stages rear arms. · Stackable and screwed type rubber pad. Fig.1 MODEL SL-6 SPECIFI…
-
8, 6 2.Take off the packaging on the machine. Take off the packing rack. 3.Move aside the parts and check the parts according to the shipment parts list. (See Fig.6 & 7) Fig.6 4. Check the parts of the parts bag according to the parts bag list (See Fig.8) Part box （65） Fig.7 Fig.8 65
…
-
12, 10 NO NO A2A2 A1 T1 T2 T3L3 L2 L1 M ～ G N L 外 接 电 源 按钮开关 F. Install plastic barrier (See Fig.15) G. Connect the power source according to the data on plate of power unit Note: For the safety of operators, the power wiring must contact the floor well Single phase motor (See Fig. 27) 1. Connecting the two power supply lines (active wire L and neutral wire N) to terminals of AC contactor marked L1, L2 respectively. 2. Connecting the two motor wires to terminals of AC contactor marked T1, T2. 3. Connecting A2 to L2 of AC contactor. 4. …
-
7, 5 III. STEPS OF INSTALLATION A. Location of installation Check and insure the installation location (concrete, layout, space size etc.) is suitable for lift installation. B. Check the parts before assembly 1. Packaged lift and hydraulic power unit (See Fig. 5) Column Power Unit Base Carriage Fig.5
…
-
21, 19 4.6 Exploded view of manual power unit Manual Power Unit 110V/60Hz/1 Phase Item Part# Description QTY Item Part# Description QTY 1 81400180 Rubber pad 2 21 41030055 AC connector 1 2 81400130 Start capacitor 1 22 81400287 Cover of Motor Terminal Box 1 3 81400088 Running capacitor 1 23 71111182 AMGO Sticker 1 4 10420148 Screw, Washer 4 24 81400560 Throttle valve 1 5 81400066 Cover of capacitor 2 25 81400266 Relief valve 1 6 81400363 Motor connecting 1 26 81400284 Plug 1 7 814…
-
19, 17 4.3 Inside Arm Assembly （ 10101034 ） exploded view ： 4.4 Cylinder Assy.（10207010）exploded view： Item Part# Description QTY 1 10209032 M8*25 Hex bolt M8*25 6 2 10209034 washerφ8 6 3 10209033 washerφ8 6 4 10209035 Moon gear 2 5 11203101 Inside Outer arm assy. 2 6 10201149 M8*12 Screw 2 7 11102006 Inside Inner arm assy. 2 Cylinder Explode View Fig.28 2 1 3 4 5 7 6 Fig.27
…
-
24, AMGO SL-6 22 2. Test with loading After finishing the above adjustment, test running the lift with loading. Run the lift in low position for several times firstly, make sure the lift can rise and lower without abnormal phenomena. And then test run the lift to the top completely. If there are anything improper, repeat the above adjustment. NOTE: It may be vibrated when lifting at start, please lifting it with load for several times, the air would be bled and the…
-
13, AMGO SL-6 11 H. Install lifting arms (see Fig.17); Lowing the carriages down to the lowest position, then use the 6# wrench to loosen the nut (See Fig. 18) Adjust the arm lock as arrow direction (See Fig. 19). Adjust moon gear and arm lock to make it to be good engagement, then tighten the nut of arm lock (See Fig. 20). Adjust the screw and arm lock Tighten the screw Fig.20 Fig.17 Fig.18 Snap Ring Loosen the screw Fig.19
…
