-
1, OPERATION & INSTALLATION MANUAL BAPTISTRY HEATER AND CONTROL SYSTEM BES6000-HC & BES6000T-HC SERIES 5.5KW BES6005-HC & BES6005T-HC SERIES 11.0KW HYDROQUIP – 510A N. SHERIDAN ST. – CORONA, CA 92880 85-0130 REV.10 05/11
…
-
2, TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS 2 PRODUCT FEATURES 5 INSTALLATION/OPERATING CONSIDERATIONS 6 ELECTRICAL INSTALLATION 7 COMPONENT CONNECTIONS 8 FLOAT SWITCH PLUMBING DIAGRAM 9 PRESSURE SWITCH PLUMBING DIAGRAM 10 SYSTEM INTERFACE MODULE 11 PLUMBING TIPS 12 EQUIPMENT DESCRIPTION 13 START UP 15 OPERATION 16 PROBLEM SOLVING 18 WARRANTY 19 HYDROQUIP PART NUMBERS HQ PART NUMBER DESCRIPTION BES-6005-HC 11KW HEATER SYSTE…
-
3, HydroQuip BES6000-HC Series IMPORTANT SAFETY INSTRUCTIONS WHEN INSTALLING AND USING THIS EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING: READ AND FOLLOW ALL INSTRUCTIONS INSTALLATION CONSIDERATIONS 1. A bonding lug has been provided on the outside of the equipment system electrical controls box. This lug permits the connection of a No. 8 AWG solid copper bonding conductor between the equipment system and all other electrical eq…
-
4, 8. WARNING - TO REDUCE THE RISK OF INJURY A. The water in a tub should never exceed 100f (38c). Before entering the tub the user should measure the water temperature with an accurate thermometer, since the tolerance of water temperature-regulating devices may vary as much as +/- 5 f (3c). A water temperatures of 100f (38c) is considered safe for a healthy adult. Lower water temperatures are recommended fo…
-
5, HydroQuip BES6000-HC Series 10. WARNING - the equipment system may be equipped with a ground fault circuit interrupter (GFCI), mounted on the electrical control box. This GFCI protects against electrical shock hazard by sensing electrical fault conditions and interrupting the electric power applied to the equipment system. Before each use of the tub the GFCI, if provided, should be tested in the following manner: Turn electric power on, P…
-
6, HydroQuip BES6000-HC Series PRODUCT FEATURES 1. GROUND FAULT CIRCUIT INTERRUPTER – This device is required for portable tubs as specified in the national electrical code article 680. The GFCI is designed to protect against potential electrical shock hazard should a ground fault occur. 2. THERMOSTAT - The thermostat regulates the water temperature of your tub. 3. TIMECLOCK (Optional): Provides timer control over heating and filtering cycles 4. PUMP RECEPTACLE – Connect pump here. 5. POWER …
-
7, HydroQuip BES6000-HC Series INSTALLATION AND OPERATING CONSIDERATIONS The equipment control system must be protected from the elements by installing it in a weather-tight enclosure. The equipment should be installed so that there is safe access for servicing and routine maintenance procedures. The single-speed circulation pump must be installed below the water level unless it is a self-priming pump. Connections between the tub and equipment control system should include shut off valves for servicing and only no…
-
8, 240 VOLT INSTALLATION - Permanently Connected Units 1. Remove the faceplate from the control box to allow access to the input wiring. 2. Connect input wiring to the terminal block as shown below. A three wire electrical service plus ground is required for a 208-240-volt connection (line 1, line 2, neutral, and ground). Failure to connect a neutral line will cause the control box to malfunction and may void the warranty. 3. Reinstall th…
-
11, PRESSURE SWITCH LEVEL KIT PLUMBING DIAGRAM 85-0130 REV.10 5/11 10
…
-
12, SYSTEM INTERFACE MODULE SEE NEXT PAGE FOR IMPORTANT TIPS 85-0130 REV.10 5/11 11
…
-
13, PLUMBING AND AUTO-FILL TIPS PLUMBING TIPS: • MEASURE TWICE DRILL ONCE • DRY-FIT PLUMBING BEFORE HOLES ARE DRILLED • FLEXIBLE PVC SHOULD BE USED BETWEEN EQUIPMENT AND BAPTISTRY • ALWAYS USE COMPATIBLE ADHESIVES AND PRIMERS AUTO-FILL VALVE TIPS: • MAY BE INSTALLED ANYWHERE • VALVE ASSY CAN BE EFFECTED BY WEIGHT, SUPPORT IF NECESSARY • FILL ASSY CAN BE PLUMBED VERTICALLY OR HORIZONTALLY • TO BYPASS FILL VALVE LOSSEN SMALL BLACK SCREW NEXT TO SOLENOID AU…
-
14, EQUIPMENT DESCRIPTION 15” RAIN/FILL ONTROL) Control plugs into the receptacle on the side of the control box. ide protection against potential electrical shock hazard n lled at the electrical service panel, a separate sub panel, or built into the FCI before each use and at least monthly when the tub is not being used WIDTH = 30” HEIGTH = 13” DEPTH = CONTROL BOX The control box contains all the ele…
-
15, Test the GFCI as follows: 1. With the power on, push the test button; the reset button should pop out. aution - If the GFCI fails to operate in this manner, do not use the tub until a qualified has corrected the problem. HERMOSTAT hen the equipment is operating, the thermostat will control the heater. Initially, adjust er ming e length of time it takes the water to reach desired temperature depends on several only. hey do not reflec…
-
16, SYSTEM INTERFACE RECEPTACLE & MODULE ystem Interface Module is stalled. SYS These indic rs system. • HEATE • PUMP “ inated whenever the system pump is activated. • HIG L ripped o trips repeatedly do not use until corrective service is performed Illuminated when the system has been mis-wired o This is an indication the 120V has been sent up the Neutral line and is a IMECLOCK (IF EQUIPPED) Pro sh the teet s …
-
17, HydroQuip BES6000-HC Series OPERATION tivate and water should begin flowing. Allow pump to run until all air is purged from the unit unit should illuminate. tion (Indicator will light l nce air is purged from the system (pressure sired lied. 1. 2. s Fill/Drain ssure switch 4. pplied. . ss the Fill/Drain button once. After the unit is drained press On/Off button once to insure that no inadvertent filling or draining can take place. Operating consi…
-
18, Operating considerations for BES with Remote Control Auto Fill/Drain (option D): 1. Insure that SYSTEM INTERFACE MODULE (DRAIN/FILL CONTROL) option is securely plugged into BES receptacle and that Auto-Drain valve cord is installed. Install one set of air tubing and air button from Remote Control on the On/Off air BES and Remote Control are set to minimum (fully CCW). If y. ay require se until the heat light on the Remote applied. . Onc…
-
19, HydroQuip BES6000-HC Series PROBLEM SOLVING Equipment system will not operate: 1. Make sure the Power Air Switch is turned “ON” 2. Check the Ground Fault Circuit Interrupter, if equipped, to see if the reset button has popped out. If it has, press reset button inward. If the GFCI trips repeatedly, contact a service technician to correct the problem. 3. Check the main circuit breaker panel. If the circuit breaker has tripped reset the breaker. If the circuit breaker trips repeatedly, contact a service …
-
20, HydroQuip BES6000-HC Series Limited Warranty Hydroquip, Inc. warrants these products to be free from defects in material and workmanship for a period of 1 year from the date of purchase (DOP), under the following provisions: From DOP to date of installation (Not to exceed 10 working days after DOP), products suspected of failure at time of installation may receive a replacement of component or like product if evaluated by Hydroquip Technical Support with an authorized service professional at the job site. …
-
21, _______________________________________________________________________ 510A SHERIDAN ST ~ CORONA, CA 92880 WARRANTY REGISTRATION PURCHASED BY: (PLEASE PRINT) Name _________________________________________________________________ Address _______________________________________________________________ City ___________________________________ State _________ Zip ______________ Telephone ( ) ____________________ DEALER: Name ___________________________________________…
