Husqvarna Viking CA 150 Operator's Manual

1, GG GG BB BB FF FF RR RR EE EE SS SS Cultivator attachment CA 150 Accessoire de cultivateur CA 150 Accesorio de cultivador CA 150 Operator ′ s manual Manuel d’utilisation Manual de instrucciones . …

2, 2 – English KEY TO SYMBOLS Symbols WARNING! The machine can be a dangerous tool if used incorrectly or carelessly, which can cause serious or fatal injury to the operator or others. Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. Always wear: • Approved hearing protection • Protective goggles or a visor This product is in accordance with applicable EC directives. Warning: rotating cutter. Keep hands and feet clear. Warning: the cutter continues to rotate …

3, English – 3 CONTENTS Contents Note the following before starting: Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the design and appearance of products without prior notice. Long-term exposure to noise can result in permanent hearing impairment. So always use approved hearing protection. Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. These instructions supplement the instructions that were included w…

4, Husqvarna Viking CA 150 4 – English SAFETY INSTRUCTIONS Personal protective equipment GLOVES Gloves should be worn when necessary, e.g., when fitting cutting attachments. HEARING PROTECTION Wear hearing protection that provides adequate noise reduction. EYE PROTECTION Always wear approved eye protection. If you use a visor then you must also wear approved protective goggles. Approved protective goggles must comply with standard ANSI Z87.1 in the USA or EN 166 in EU countries. BOOTS Wear sturdy, non-slip boots. CLOTHING Wear cl…

5, Husqvarna Viking CA 150 English – 5 SAFETY INSTRUCTIONS General safety precautions • Never allow children to use the machine. • Ensure that no-one comes closer than 15 m while you are working. • Never allow anyone else to use the machine without first ensuring that they have understood the contents of the operator’s manual. Safety instructions before starting work • Inspect the working area. Remove all loose objects, such as stones, broken glass, nails, steel wire, string, etc. that could be thrown out or become wrap…

6, Husqvarna Viking CA 150 6 – English SAFETY INSTRUCTIONS General working instructions Basic safety rules 1 Look around you: - To ensure that people, animals or other things cannot affect your control of the machine. - To ensure that people, animals, etc., do not come into contact with the cutting attachment or loose objects that are thrown out by the cutting attachment. 2 Do not use the machine in bad weather, such as dense fog, heavy rain, st…

7, English – 7 WHAT IS WHAT? What is what on the cultivator attachment? 1 2 3 4 5 6 7 8 1 Blade guard 2 Shaft 3 Blades 4 Split pin 5 Cotter pin 6 Grease filler cap, bevel gear 7 Bevel gear 8 Operator ′ s manual …

8, 8 – English ASSEMBLY Fitting the bevel gear • Assembling the angle gear on the shaft. Turn the shaft so that the splines on the drive axle mate in the angle gear. • First tighten the screw H and then the screw M. Assembling the guard. • Remove the four screws C and the two screws F from the bracket A. • Place the rubber sleeve D on the shaft E. The rubber sleeve should sit between the arrow markings on the shaft. • Place the bracket A around the rubber sleeve and fit the screws F loosely. • Guide the gua…

9, English – 9 STARTING AND STOPPING Check before starting For safety reasons follow these recommendations! • Inspect the working area. Remove any objects that could be thrown out. • Check that the machine is in perfect working order. Check that all nuts and screws are tight. • Check the tines and tine guard to ensure they are undamaged and show no signs of cracking. Replace the tine and tine guard if they have been exposed to impact or are cracked. …

10, Husqvarna Viking CA 150 10 – English MAINTENANCE Bevel gear The bevel gear is filled with the right quantity of grease at the factory. However, before using the machine you should check that the bevel gear is filled three-quarters (40g) full with grease. Use HUSQVARNA special grease. CAUTION! The gear housing must not be filled completely with grease. The grease expands as the machine heats up during operation. If the gear housing was complet…

11, English – 11 TECHNICAL DATA Technical data Technical data CA 150 Weight Weight, Lbs/kg 2,9 Blades Diameter tines, mm 220 Working width, mm 150 Tine speed at engine speed 10,500 r/min 215 …