Kenmore 721.80402 Installation Instructions Manual

Installation Instructions Manual for Kenmore 721.80402 Microwave Oven (19 pages)

Specifications:

494/494352-72180402.pdf file (09 Apr 2024)
  • Manufacturer: Kenmore
  • Category of Device: Microwave Oven
  • Document: 721.80402, File Type: PDF Installation Instructions Manual
  • Updated: 09-04-2024
  • Count of Pages: 19
Download 721.80402 Manual (19 pages)

Kenmore 721.80402: Read PDF Manual Online

Data: UPD 9th April 2024

Kenmore 721.80402 Microwave Oven PDF Installation Instructions Manual (Updated: Tuesday 9th of April 2024 03:35:12 AM)

Rating: 4.2 (rated by 79 users)

Compatible devices: 767. 8505, 40180099010, 592.85600-0, 721.60109, 204.73772610, 592-857130, 767.8541000, 911.49485.

Recommended Documentation:

Kenmore 721.80402: Text of Installation Instructions Manual

(Ocr-Read Version Summary of Contents, UPD: 09 April 2024)
  • lVlodeis/lVlodelos

    721.80402

    721.80403

    721.80404

    721.80409

    72t.80522

    721.80523

    721.80524

    721.80529

    721.80414

    721.80419

    721.80413

    721.80412

    Read and save these

    installation instructions.

    Lea y guarde estas

    instrucciones de

    instalaci6n

    iNSTALLATIONINSTRUCTIONSI

    I

    I

    1

    ®

    icrowaveHood Combination

    Combinaci6n

    icroondasCampana

    m

    Z

    t"

    m

    g_

    z

    m

    {n

    Z_

    0

    t"

    Part No. 3828W5U0437 Sears, Roebuck and Co., Hoffman Estates, IL. 60179 U.S.A www.sears.com.

  • YOUR SAFETY FIRST

    BEFORE YOU START

    * Proper installation is the installer's responsibility!

    - Read the entire manual before you begin.

    - The model number label is located on the oven front. See Figure 1.

    - Mounting plate is located on back side of microwave oven, See Figure 2.

    BE SURE TO READ THE FOLLOWING SAFETY iNSTRUCTiONS:

    Model Number Label Mountinc Plate

    m

    Z

    t"

    m

    Z

    Back of oven

    Figure I Figure 2

    Ak WARNING Ak

    FOR YOUR SAFETY:

    o You will need TWO people to install this oven. It is heavy and could cause personal injury if not handled

    properly. The dimensions of the oven are as follows:

    Height : 16-7/16 inches

    Width :29-15/16 inches

    Depth : 15-3/8 inches

    Weight : 54 pounds

    o AVOID ELECTRICAL SHOCK!

    - Before you drill into the wall, note where electrical outlets are and where electrical wires might be

    concealed behind the wall.

    YOU COULD GET AN ELECTRIC SHOCK it you contact electrical wires with your drill bit.

    - Locate and disconnect the power of any electrical circuits that could be affected by installing this oven.

    IF YOU DO NOT DISCONNECT THE POWER, YOU COULD GET AN ELECTRIC SHOCK.

    ,, ELECTRICAL RATING OF THIS OVEN : 120V, 60Hz.

    - You need a 120V, 60Hz, AC only, 20A, fused electrical supply (located in the cabinet above the

    microwave as close as possible to the microwave circuit) serving only the microwave.

  • YOUR SAFETY FIRST

    • THIS APPLIANCE MUST BE GROUNDED!

    - If there is an electrical short circuit, grounding reduces the risk of electrical shock by providing an escape

    wire for the electric current. This appliance is equipped with a cord having a grounding wire with a

    grounding plug.

    PROPERLY POLARIZED AND

    • Place the plug into a properly installed and grounded GROUNDED OUTLET

    outlet. See Figure 3.

    • Do not use an extension cord.

    • Keep the power cord dry and do not pinch or crush it.

    • DO NOT, UNDER ANY CIRCUMSTANCES, REMOVE

    THE POWER SUPPLY CORD GROUNDING PRONG!

    This appliance MUST be grounded!

    Three-Pronged (Grounding) plug

    Figure 3

    Ak WARNING

    If you use the grounding plug improperly, you risk electric shock!

    - Check with a qualified electrician if you are not sure whether the oven is properly grounded or if you do

    not completely understand the grounding instructions.

    DO NOT USE A FUSE IN THE NEUTRAL OR GROUNDING CIRCUIT.

    ¢}

    Ul

    3:

    Zk WARNING

    Improper grounding could result in electric shock or other personal injury.

    SAVE THESE INSTRUCTIONS FOR THE LOCAL ELECTRICAL INSPECTOR'S USE.

    • DO NOT EXPOSE YOURSELF TO EXCESSIVE MICROWAVE ENERGY!

    - DO NOT try to operate the microwave oven with the door open.

    - DO NOT tamper with or defeat the safety interlocks.

    - DO NOT place objects between the microwave oven front face and the door.

    - DO NOT allow soil or cleaner residue to build up on the flat surfaces around the microwave oven door.

    - DO NOT operate the microwave oven if it is damaged.

    - The microwave oven door must close properly to operate safely.

    - DO NOT use the microwave oven:

    • If the door is bent.

    • If the hinges or latches are broken or loose.

    • If the door seals, sealing surfaces or glass is broken.

    - DO NOT attempt to adjust or repair the oven yourself!

    It should be adjusted and repaired by a qualified technician who can check for microwave leakage after

    repairing the oven.

    WARNING A

    If you do not use the microwave oven as instructed, you could be exposed

    to excessive microwave energy.

  • YOUR SAFETY FIRST

    • MAKE SURE YOU HAVE ENOUGH SPACE AND SUPPORT.

    - Mount the oven against a flat, vertical wall, so that it is supported by the wall. The wall should be

    constructed of minimum 2" x 4" wood studding and 3/8" thick drywall or plaster/lath.

    - ATTACH AT LEAST ONE of the two lag screws supporting the oven to a vertical, 2" x 4" wall stud.

    - DO NOT mount the microwave oven to an island or peninsula cabinet.

    - BE SURE the upper cabinet and rear wall structures are able to support 150 Ibs., plus the weight of any

    items you place inside the oven or upper cabinet.

    - Locate the oven away from strong draft areas, such as windows, doors, and strong heating vents.

    - BE SURE you have enough space. See Figure 4 below for minimum vertical and horizontal clearance.

    WARNING

    If you do not mount the oven as instructed, you risk personal injury and/or

    property damage.

    30"rain, cabinet openingwidth'

    30" rain, clearancefrom bottom

    of cabinetto cookingsurface

    or countertop

    (Use templates included

    /Grounded Plug

    (inside upper cabinet)

    Power Supply

    Cord Hole

    with installation instructions)

    Figure 4

    CAUTION

    • Before you begin installing the oven, PLACE A PIECE OF THE CARTON OR OTHER HEAVY MATERIAL

    (a blanket) over the countertop or cooktop to protect it. Do not use a plastic cover.

    Failure to protect these surfaces could result inproperty damage.

  • PARTS, TOOLS, MATERIALS

    THE FOLLOWING PARTS ARE SUPPLIED WITH THE OVEN:

    NOTE: Depending on your ventilation requirements, you may not use all of these parts.

    Damper/duct connector

    (for roof vented or wall vented installation)

    Not Actual Size

    One power cord clamp and

    One dark-colored mounting screw

    (to hold the power cord)

    Actual Size

    One power cord clamp bushing - Actual Size (for the cord hole in a metal upper cabinet)

    Four 1/4" x 2" lag screws - Actual Size

    (for wall stud holes)

    Four 1/4" x 3" toggle bolts - Actual Size

    (for drywall holes)

    61

    01

    Two 1/4" x 3" bolts - Actual Size

    (for securing to the upper cabinet)

    OR

    Four spring toggle heads - Actual Size

    (for the toggle bolts)

    Two tapping screws - Actual Size

    (for attaching the damper duct connector)

    One upper cabinet template - Not Actual

    Size

    D

    One rear wall template- Not Actual Size

    I

    REAR WALI_ TEMPLATE :

    NOTE: You need to install at least one lag screw into a 2" x 4" stud and four anchor bolts into the wall,

    and the mounting area must meet the 150 Ibs. weight requirement.

  • PARTS, TOOLS, MATERIALS

    YOU WILL NEED THE FOLLOWING TOOLS AND MATERIALS FOR THE

    INSTALLATION:

    Carton or other heavy material for covering the counter top.

    Clear Tape

    (for taping the templates to the wall)

    Stud Finder or Thin Nail

    Saber Saw (for cutting vent holes for roof

    or wall vending)

    Phillips Screwdriver (for the screws)

    Pencil

    Flat Blade Screwdriver (for the toggle bolts)

    Measuring Tape (metal preferred)

    Keyhole Saw (for the power cord hole)

    1/2" and 3/16"

    drill bits ,,.,,=,=====

    Plumb Line

    Duct Tape

    Small Side Cutters or Tin Snips

    Caulking gun

    * If you have brick or masonry walls, you need special hardware and tools.

    * The ductwork you need for the installation is not included. All wall and roof caps must have a back-draft

    damper.

  • STEP 1: PREPARE THE

    ELECTRICAL CONNECTIONS

    _, WARNING A

    AVOID ELECTRICAL SHOCK! THIS APPLIANCE MUST BE GROUNDED!

    1. Locate the grounded electric outlet for this oven in the

    cabinet above the oven, as shown in Figure 4 Detail.

    NOTE: The outlet should be on a circuit dedicated to the

    microwave oven 120V, 60Hz., AC only, with a

    20ampere fused electrical supply.

    IMPORTANT: If you do not have the proper wall outlet,

    you MUST have one installed by a qualified

    electrician.

    2. You will cut the power-supply-cord hole (shown in

    Figure 4 Detail) later when you prepare the wall and

    upper cabinet in Step 4.

    NOTE: Do not use an extension cord.

    Keep the power cord dry and do not pinch or crush it.

    Upper I

    Cabinet : :';

    Grounded Outlet

    Q

    T

    Power-Supply-Cord Hole

    Figure 4 Detail

    61

    _, WARNING _,

    Improper grounding could result in electric shock or other personal injury.

    • DO NOT, UNDER ANY CIRCUMSTANCES, REMOVE THE POWER SUPPLY

    CORD GROUNDING PRONG!

    • This appliance MUST be grounded!

  • STEP 2:

    PREPARE THE VENTING S YSYTEM

    NOTE: The ductwork you need for outside ventilation is not included with your oven. The standard ductwork

    fittings and length are shown in Figure 9, page 9.

    WARNING - FIRE HAZARD

    THIS OVEN MUST BE PROPERLY VENTED!

    You may vent your oven in one of three ways:

    Roof Venting If your oven is located on an outside wall near the roof, as in Figure 6 (3-1/4" x 10" duct) and

    Figure 8 (6" round duct.)

    Wall Venting If your oven is located on an outside wall on the first floor of your house, as in

    Figure 5 (3-1/4" x 10" duct) and Figure 8 (6" round duct.)

    Room Venting If your oven is located on an inside wall of your house, as in Figure 7.

    NOTE: If you choose the rear exhaust method (roof or wall venting), be sure there is enough clearance within

    the wall for the exhaust duct.

    cabinet

    .,

    Wall venting

    Wall Venting

    /

    3-1/4"xl 0"

    duct

    Figure 5

    wall cap

    through-the-wall

    cabinet

    .-

    Roof venting

    Roof Venti ng

    duct [_

    through-the-roof

    Figure 6

    REMEMBER AS YOU INSTALL THE VENTING:

    * Keep the length of the ductwork and the

    number of elbows to a minimum to

    ventilate your oven efficiently.

    See examples on page 9.

    • Keep the size of the ductwork the same. cabinet

    • Do not install two elbows together.

    • Use duct tape to seal all joints in the duct

    system.

    • Use caulking to seal the exterior wall or

    roof opening around the cap.

    Room Venting

    ove

    Figure 7

    roof cap

    6" min. wall cap

    diameter

    round

    elbow

    3-1/4" to round ,/

    duct transition

    3-1/4" to round

    ductworktransition

    Figure 8

  • STEP 2:

    PREPARE THE VENTING S YSYTEM

    STANDARD FITTINGS

    NOTE: If the existing duct is round, you must use a rectangular-to-round adapter, with a rectangular 3" extension

    duct installed between the damper assembly and the adapter to prevent the exhaust damper sticking.

    DUCT LENGTH

    The total length of the duct system, including straight duct, elbows, transitions, wall or roof caps must not

    exceed the equivalent of 140 feet.

    For best performance, do not use more than three 90 degree elbows.

    Below are the standard fittings and their equivalent length in feet.

    3 1/4"x 10" to 6" = 5 ft.

    >

    3 1/4" x 10" roof cap = 24 ft

    3 1/4" x 10"900elbow = 25 ft

    3

    90°elbow = 10 ft

    3 1/4" x 10" wall cap

    = 40 ft

    45°elbow = 5 ft

    Figure 9

    3 1/4" x 10" flat elbow

    = 10ft

    61

    To calculate the equivalent length of each duct piece used, see the examples below.

    I

    Examples

    For 3 1/4" x 10" SYSTEMS For 6" ROUND SYSTEMS

    3-1/4"x10" 14----- 6ft. --_1 _[3wall cap

    90°elbow _\

    H,

    2ft.

    1-3 1/4" X 10" 90 ° elbow =

    1-Wall Cap =

    8 feet straight duct =

    TOTAL LENGTH =

    25 ft.

    40 ft.

    8ft.

    73 ft.

    90° elbows _---- 6ft. --_[_/wall cap

    transi_

    1-transition = 5 ft.

    2-90 ° elbows = 20 ft.

    1-Wall Cap = 40 ft.

    8 feet straight = 8 ft.

    TOTAL LENGTH = 73 ft.

  • STEP 3:

    PREPARE THE VENTING BLOWER

    Your microwave oven is shipped with the blower assembled for room venting (recirculating). You need to adjust

    the blower if you want wall vented or roof vented installation.

    Ak WARNING Ak

    ELECTRICAL SHOCK HAZARD! UNPLUG UNIT BEFORE WORKING ON IT.

    o DO NOT PULL OR STRETCH THE BLOWER WIRING! Pulling and stretching the blower wiring could result

    in electrical shock.

    REMOVE THE MOUNTING PLATE:

    1. Remove any shipping materials and parts from inside

    the microwave oven.

    2. Cover the counter top or cooktop with a thick,

    protective covering to protect it from damage and dirt.

    See Figure 10.

    NOTE: If you have a free-standing range, disconnect

    it, move it onto a piece of cardboard or

    hardboard and pull it away from the wall, so

    that you can get closer to the upper cabinet

    and back wall for easier measuring and

    drilling.

    3,

    4,

    5,

    6,

    Remove mounting plate 2 screws from the mounting

    plate as shown and discard them.

    (See Figure 11.)

    This plate will be used as the rear mounting plate.

    (It will be used to locate and mark the mounting holes

    on the rear wall.)

    Locate exhaust adaptor, grease filters and hardware

    packet.

    At this point, remove any adhesive tape (if there is

    any), on the exhaust adaptor, the grease filters and

    the power supply cord.

    ROOM VENTED INSTALLATION:

    Go to STEP 4, PREPARE THE WALL AND UPPER

    CABINET FOR INSTALLATION located on page 13.

    Figure 10

    Control panel side

    Figure 11

    10

  • STEP 3:

    PREPARE THE VENTING BLOWER

    WALL VENTED INSTALLATION:

    1. Remove one blower unit mounting screw and

    two blower plate screws. Remove the blower

    plate from cabinet. See Figure 12.

    2. Carefully lift the blower unit out of the microwave

    oven. Disconnect the blower wire from

    connector. See Figure 13.

    3. Use side cutters or tin snips to cut and remove

    knockouts "B" from Back plate. Discard

    knockouts. Be careful not to distort the plate.

    See Figure 14.

    4. Rotate the unit so that the exhaust ports face the

    rear of the cabinet. See Figure 15. Before you

    insert blower unit, blower wire must be like

    Figure 15.

    5. Reassemble the blower wire into the connector.

    6. Place blower unit back into cabinet. Check that

    the exhaust ports face towards the rear of the

    cabinet. See Figure 16.

    7. Reattach the blower plate to the top of the

    cabinet as it was originally assembled. Attach

    with one blower unit mounting screw and then

    two blower plate mounting screws.

    See Figure 17.

    8. Go to STEP 4, PREPARE THE WALL AND

    UPPER CABINET FOR INSTALLATION

    located on page 13.

    blower unit

    Knockouts "B"

    blower plate

    •connector

    -- back plate

    blower plate

    mounting screws

    blower unit

    mounting screw

    Figure 12

    .blowerwire

    Figure 13

    61

    Knockouts Parts "B"

    blower

    unit

    exhaust

    ports

    Figure 14

    exhaust

    ports

    Figure 15

    blower plate

    mounting

    screws

    blower unit

    mounting screw

    Figure 16 Figure 17

    11

  • STEP 3:

    PREPARE THE VENTING BLOWER

    ROOF VENTED INSTALLATION:

    1. Remove one blower unit mounting screw and

    two blower plate screws. Remove the blower

    plate from cabinet. See Figure 18.

    blower plate

    mounting

    screws

    2. Carefully lift the blower unit out of the

    microwave oveR.

    3. Rotate blower unit 90° so the exhaust ports

    face the top of the cabinet. See Figure 19.

    4. Place blower unit back into microwave oven.

    5,

    Use side cutters or tin snips to cut and remove

    knockouts "A" from blower plate. Discard

    knockouts. Be careful not to distort the plate.

    See Figure 20.

    6.

    Reattach blower plate to microwave oven.

    Attach with the one blower unit mounting

    screw and then the two blower plate mounting

    screws. See Figure 21.

    blower plate -o_

    blower unit

    mounting screw

    Figure 18

    blower

    unit

    Figure 19

    Knockouts "A"

    blower plate

    Figure 20

    blower unit _ _ blower plate

    __-_ _ mounJ_ng

    blower plate blower unit

    mountingscrews

    Figure 21

    12

  • STEP 4: PREPARE THE WALL AND

    UPPER CABINET FOR INSTALLATION

    MEASURE AND TACK / TAPE UP THE

    TEMPLATE

    1. Using a plumb line and (metal) measuring tape, find

    and mark the vertical center line __

    ,_/_on the back

    wall, as in Figure 22.

    2. Find and mark one or two points where the studs

    are on the wall (Studs are normally 16 inches apart.)

    and then measure and mark the stud locations. If

    you cannot find any wall stud, consult a local

    building contractor.

    CAUTION A

    DO NOT ATTEMPT TO INSTALL THE

    MICROWAVE OVEN IF YOU CANNOT FIND A

    WALL STU D.

    3. Line up the plumb line on the wall with the center

    line on the mounting plate.

    NOTE: Be sure the minimum width is 30 inches and

    the distance from the top of the mounting

    plate to the range or counter top is at least

    30 inches. See Figure 4 on page 4.

    4. Center mounting plate in opening by lining up the

    plumb line on wall with centerline on mounting plate.

    Make sure the minimum width is 30 inches and that

    the top of the mounting plate is located a minimum

    of 30 inches above the cooking surface.

    See Figure 23.

    NOTE: If the front edge of the cabinet is lower than

    the back edge, adjust the mounting plate to

    be level with the cabinet front.

    5. Measure the bottom of the upper cabinet frame.

    Trim the edges "A", "B" and "C" on the upper

    cabinet template so that the template will fit on the

    bottom of the upper cabinet. If upper cabinet has a

    recessed frame, trim template so that it fits inside

    the recessed area. Align the centerline of the upper

    cabinet template with the centerline of the mounting

    plate; then securely tape or tack the upper cabinet

    template in place. See Figure 23.

    ©

    Figure 22

    Figure 23

    ©

    13

  • STEP 4: PREPARE THE WALL AND

    UPPER CABINET FOR INSTALLATION

    DRILL THE HOLES IN THE WALL AND UPPER CABINET.

    Zk WARNING

    BE VERY CAREFUL WHEN DRILLING HOLES INTO THE WALL.

    Electrical wires could be concealed behind the wall covering and if the drill hits them you

    could get an electric shock.

    1,

    2,

    3,

    Find the points on the mounting plate labeled "A", "B", "C" and "D". Drill a 3/16" diameter hole at any of

    these points that are in front of a wall stud. Drill a 3/4" diameter hole at any of these points that are over

    drywall.

    Drill a 3/8" hole at points "J" and "K" on the upper cabinet template.

    NOTE: If the bottom of the upper cabinet is recessed 3/4" or more, you will need 2"x2" filler blocks (not

    included) to provide additional support for the bolts. See Figure 24.

    • Mark the center of each filler block and drill a 3/8" diameter hole at the mark.

    • Align filler blocks over the two openings in the top of the microwave oven cabinet and attach to cabinet with

    masking tape. See Figure 25.

    Cut or drill a 2" diameter hole at the area marked "M", "power supply cord hole" on the upper cabinet template.

    If the upper cabinet is metal, you will need to cover the edge of the hole with the power supply cord bushing

    (supplied) to prevent damage to the cord from the rough metal edge.

    WARNING

    YOU MUST COVER THE EDGE OF

    THE POWER SUPPLY CORD HOLE

    IN A METAL CABINET WITH THE

    POWER SUPPLY CORD BUSHING.

    FAILURE TO DO SO COULD

    RESULT IN DAMAGE TO THE CORD

    AND ELECTRIC SHOCK.

    cabinet front filler block

    Figure 24

    cabinet

    bottom shelf

    4. Cut out the venting areas (with the saber saw):

    • Roof Venting: cut out the shaded area marked "L"

    on the upper cabinet template.

    • Wall or Room Venting (Recirculating): go to STEP

    5, INSTALL THE MOUNTING PLATE, located on

    page 15.

    5. Use caulking compound to seal the exterior wall or

    roof opening around the wall cap or roof cap.

    filler

    block

    Figure 25

    14

  • STEP 5: INSTALL THE MOUNTING

    PLATE TO THE WA LL

    THE OVEN MUST BE CONNECTED

    TO AT LEAST ONE WALL STUD.

    1. Draw a vertical line on the wall at the center of the

    30" wide space.

    Use the mounting plate as the template for the

    rear wall. Place the mounting plate on the wall,

    making sure that the tabs are against the bottom

    of the cabinet. Line up the notch and center line

    on the mounting plate to the center line on the

    wall.

    2. While holding the mounting plate with one hand,

    draw circles on the wall at holes "A", "B", "C"

    and "D". Four holes must be used for mounting. If

    the holes are not used, the installation will not be

    secure. Installer must use these holes for proper

    installation. Use toggle bolts through these holes

    unless one of them lines up with a stud. Use a

    wood screw for studs. See Figure 26.

    NOTE: Draw a fifth circle inside area "E", through

    one of the holes to match the location of a

    stud.

    For wall vented: The oven requires a rear wall

    cutout opening for the rear wall duct and the

    exhaust adaptor must be attached to the Back of

    oven. See the next page on how to prepare the rear

    wall cutout opening and the exhaust

    adaptor/mounting plate for wall vented.

    3. Drill holes through the circles. If there is a stud,

    drill a 3/16" hole for lag screws. Two or preferably

    four lag screws at holes "A" and "C", or "B" and

    "C" must be used to secure mounting plate to

    wall. If there is no stud, drill a 3/4" hole for toggle

    bolts. Make sure to use at least 1 lag screw at

    holes of area "E" in a stud, and 4 toggle bolts at

    holes "A", "B", "C" and "D" in the drywall or the

    plaster.

    4. Attach the plate to the wall. To use spring toggle

    head bolts: Remove the toggle wings from the

    bolts. Insert the bolts into the mounting plate and

    replace the spring toggle heads to 3/4" past the

    bolt ends. Insert the spring toggle heads into the

    holes in the wall to mount the bracket. You may

    pull forward on the bracket to help in tightening

    the toggle bolts. Tighten all bolts. See Figure 27.

    3/16" Hole on Studs

    3/zl" Hole on Drywall Only

    Minimum 66" ]

    rom the Floor/ I I

    I I PorWa,-

    I I/ ve°ted°°'

    I '

    I I;ioC _-- --_ DQ'il

    I p:,/zW...... J_-_'4

    / _' J I ',k

    m

    o ; Draw Lines i _

    / / on Studs I_ _

    t _ t

    , I _ Draw _ _

    _l/ [ Center Line I_q _

    Mounting =

    IIHE/_ Plate _ I I

    , []

    IIII/,'[]Centerhine= 1 D_ Io I

    l = =1_- J t

    SupportTab SuppertTab

    Figure 26

    ;11_;I_ Space More Than Wall Thickness

    I Toggle Wings

    Mounting III I"

    Plate_l I::11 ,, Toggle BoltN/..!L,

    qlHi,iX _ _ IIl_\

    Bolt

    End

    Figure 27

    15

  • STEP 5: INSTALL THE MOUNTING

    PLATE TO THE WA LL

    TO PREPARE THE REAR WALL

    CUTOUT OPENING AND EXHAUST

    ADAPTOR/MOUNTING PLATE FOR

    WALL VENTING AND ROOF VENTING:

    NOTE: If room vented installation is used, skip this

    step.

    1. Place the mounting plate against the rear wall as

    described in step 5 item 1 (page 15).

    2. Use the wall template to determine the location and

    size of the box cutout for the rear wall duct. See

    Figure 28.

    Attach the exhaust adaptor to the rear mounting

    plate by sliding it into the guides at the top center

    of the plate on the wall side. Push in securely until

    it is past the top locking tabs and in the lower

    locking tabs. Take care to assure the damper

    hinge is installed so that it is at the top and that the

    damper swings freely.

    Carefully guide the exhaust adaptor, now attached

    to the Back of oven, into the house duct, before

    using the screws to attach the plate to the wall.

    This will assure proper alignment for installation.

    See Figure 29.

    Return to step 5, item 3 (page 15) to continue.

    After completing the installation of the Back of

    oven, again check the rear damper for free

    movement to assure it will operate properly.

    t

    I

    REAR WALL TEMPLATE

    C ± J

    Figure 28

    Exhaust Adaptor ._

    Slide exhaust

    adaptor into

    guides on I

    rear panel. I

    Locking

    Tabs

    Damper

    (hinge side up)

    Back of oven

    (wall side)

    Guides

    Figure 29

    16

  • STEP 6:

    ATTACH THE OVEN TO THE WALL

    _, WARNING

    You will need two people to lift this

    microwave. Failure to use more

    than one person could result in

    personal injury.

    1. Carefully lift microwave oven and hang it on support

    tabs (See Figure 26) at the bottom of the mounting

    plate. Reaching through upper cabinet, thread

    power supply cord through the power supply cord

    hole in the bottom of the upper cabinet.

    See Figure 30.

    2. Rotate the microwave oven upward so the top of

    oven is against the bottom of the upper cabinet or

    cabinet frame.

    ffl

    Figure 30

    3. Then insert a bolt down through each hole in the

    upper cabinet bottom. See Figure 31.

    Tighten the bolts until the gap between the upper

    cabinet and microwave oven is closed.

    4. If wall vented or room vented installation is used, go

    to No. 7 on the next page.

    Figure 31

    17

  • STEP 6:

    ATTACH THE OVEN TO THE WALL

    5. Roof vented installation: See Figure 32.

    Install ductwork through the vent opening in the

    upper cabinet. Complete the venting system through

    the roof according to the method needed. See

    "PREPARE THE VENTING SYSTEM," STEP 2 on

    the page 8. Use caulking to seal exterior roof

    opening around the exhaust cap. See Figure 6 on

    page 8.

    6. Use power supply cord clamp to bundle the power

    supply cord. Install the power supply cord clamp,

    using a screw as shown in Figure 33, to inside of

    the cabinet.

    7. To install the grease filter: Slide it into the slide slot,

    then push up and toward oven center to lock.

    See Figure 34.

    8. Plug in the power supply cord.

    9. Read your Owner's Manual, then check the

    operation of your microwave oven.

    i damper Ji_l

    Figure 32

    i I I 1-':-1 !_\lil I ,,power

    i I I1©1 }_WI supply

    i I I_=_ J J/ I cord

    clamp

    Figure 33

    L..j

    Figure 34

    18

  • MEMO

    19

  • Kenmore 721.80402 User Manual
  • Kenmore 721.80402 User Guide
  • Kenmore 721.80402 PDF Manual
  • Kenmore 721.80402 Owner's Manuals

DOC-d8a06cc:

Recommended for Kenmore 721.80402 Owners: SoundStyle AVF302, DCC-FMT50U, ZTL75, CS071AE

Kulinarisk, DE68-01931A-01, 700-06050, BMC253SS, KOG-37A50S
  • 23R-890N(S)/(W)QUICK START GUIDE1 DIGITAL DISPLAY2 MULTI COOK pad3 CONVENIENCE/PIZZA pad4 MORE, LESS pads 5 GRILL pad6MIXpad 7 NUMBER ANDTEMPERATURE pads8 STOP/CLEAR pad9 EASY DEFROST pad10 HELP pad11 CONVEC pad12 PREHEAT pad13 POWER LEVEL pad14 CLOCK pad15INSTANT COOK/START pad16 INSTANT ACTION pa ...

    Model & Doc Type: R-890N 1

  • Write the model and serial numbers here:Model # _________________Serial # _________________You can find them on a label when the door is open.GE is a trademark of the General Electric Company. Manufactured under trademark license.ESPAÑOLPara consultar una version en español de este manual de inst ...

    Model & Doc Type: JES1109 48

  • ULTIMA COOK™ SPEED OVENUse & Care GuideFor questions about features, operation/performance, parts accessories or service, call: 1-800-422-1230www.kitchenaid.comTable of Contents............................................................................................................2Model ...

    Model & Doc Type: ULTIMA COOK KHHS179L 24

  • Microwave Oven Model CE2139MO INSTRUCTION MANUAL PLEASE SAVE THESE INSTRUCTIONS Dear Valued Customer Thank you for purchasing a CASCADE appliance. We understand the importance of your purchasing decision, and appreciate your final choice to introduce ...

    Model & Doc Type: CE2139MO 10

  • ZE2160SF – GE Monogram® Microwave OvenDimensions (in inches)Note: JX2127SH or JX2130SH kit is required for in-cabinet installation. The trim frame protrudes forward of cabinetry to allow airflow from the top, bottom and sides of the frame. Allow 1" clearance beyond the edge of the trim frame ...

    Model & Doc Type: ZE2160SF 2

  • MODEL: D80D20ESLRIII-B7 CONVECTION MICROWAVE OVEN M i c r o w a v e O v e n O w n e r ' s M a n u a l Please read these instructions carefully before installing and operating the oven. Record in the space below the SERIAL NO. found on the nameplate on your oven a ...

    Model & Doc Type: D80D20ESLRIII-B7 12

  • INSTALLATION INSTRUCTIONS27" (68.6 CM) AND 30" (76.2 CM) ELECTRICBUILT-INMICROWAVE OVEN. INSTRUCTIONS D'INSTALI.A,TIpNFOUR A MICRO-ONDES ENCASTREELECTRIQUEDE 27" (68,6 CM) ET30" (76,2 CM)TableofContents/Tabledes mati@resBUILT-IN MICROWAVE OVEN SAFETY ............. ...

    Model & Doc Type: KBHS109SSS04 12

  • OWNER’S MANUALMicrowave OvenISMW11 001 2 3;i&j\7PP,J1. Read these instructions carefully before installing and operating theoven. Keep them for future reference.2. Record in the space below the SERIAL NO. found on the nameplate onour oven and retain this information for future reference.SERI ...

    Model & Doc Type: SMW1100 16

  • B2310Samsung� ...

    Model & Doc Type: B2310 72

  • Navodila za uporabo Upute za uporabu Uputstvo za upotrebu Упатства за употребаInstruction manualGebrauchsanweisungNotice d'utilisationHasználati utasításInstrukcja obsługiNávod na obsluhuNávod na použití Инструкции за употребаIИнструкци ...

    Model & Doc Type: GMO 20 DGW 148

Additional Information:

# Brand Model Document Type/File Pages File Size Last Checked
1 Silvercrest
SMW 900 EDS B4
172 03/04
2 Smeg
SF4390MCX
3 12/06
3 Haier
MWM10100SS - 1.0 cu. Ft. 1000W Microwave Oven
19 0.7 Mb 22/03
4 Whirlpool
MWF 863
22 25/05
5 Toshiba
ML-EM45P
20 22/05
6 Sanyo
EM-X680
24 01/05
7 Candy
CMW 2070S
84 26/03
8 IKEA
FRAMTID MW6
22 18/03
9 IKEA
GRÄNSLÖS
32 30/03
10 Samsung
MS11J5023A
112 23/01
11 AEG
MICROMAT 21T-d/w
28 0.63 Mb 11/03
12 Bosch
Vision 500 Series WTVC533
68 19/01
13 Samsung
MS22M8054A Series
140 17/12
14 Caple
CM103
20 0.2 Mb 24/03
15 Kuppersbusch
EMWK 1030.0E
60 19/05
16 GE
JE1530
24 11/03
17 ETNA
CM125HRVS
97 06/04
18 Smeg
MM181N
15 0.23 Mb 29/02
19 Cylinda
IM 80 MG RF
44 03/01
20 Hitachi
MSU23
17 0.22 Mb 29/03
Popular Right Now:
# Brand Model Document (PDF) Pages Size Check Date
1 Moffat
MSF 610
8 25.04.
2 Sony Ericsson
W205
42 1.5 Mb 14.04.
3 Vertex Standard
VX-4600 Series
45 23.03.
4 IKEA
LUFTIG
28 03.01.
5 Philadelphia Scientific
HydroPure PS-300
2 21.12.
6 Graco
PRO 3500WB
48 11.06.
7 andrews
WH42
64 26.04.
8 Bras
B3
56 30.12.
9 fakro
ZWS12
8 06.06.
10 Pioneer
DDJ-T1
96 17.06.
11 Asus
E3060 WiFi-AP Solo
59 23.12.
12 Clay Paky
PIPER MS HTI 150
3 04.01.
13 Lenovo
ThinkPad SL500
2 19.04.
14 Jireh
Circ-it
48 13.06.
15 ABB
MegaFlex UL S1 Series
86 15.05.
16 NEC
PX803UL
12 22.01.
17 JVC
TM-H1375SU - Color Video Monitor
16 08.12.
18 Polytron
TSM 32 HD
20 20.06.
19 Indesit
IWB 61051
72 11.12.
20 Remington
SMOOTH AND SILKY WDF-4840
10 12.05.
21 Superabrasive
LAVINA 30G-X
34 15.04.
22 Gigaset
sl930 a
2 14.12.
23 Audio Technica
ES933H
2 0.13 Mb 11.02.
Operating Impressions, Questions and Answers: