-
13, Omega Engineering 100/200 Series OMB-DaqBook User’s Manual 10-29-02 Setup and Startup 2-3 JP2 – DAC Reference Voltage and SSH (Simultaneous Sample and Hold) JP2 selects an Internal (default) or External reference voltage for the two separate analog outputs. JP2 also selects SSH (default) for applications using one or more of the following: DBK2, DBK4, DBK5, DBK7, DBK17, DBK50, or DBK51. We recommend that you leave these jumpers at the factory defau…
-
49, Appendix A – Specifications, DaqBooks 02-14-02 A-3 Analog Outputs Channels: 2 Connector: DB37 male, P1 Resolution: 12 bits Voltage Ranges: 0 to 5 VDC with built-in reference; 0 up to ±10 VDC with external reference Maximum Output Current: 10 mA General Purpose Digital I/O for DaqBook/100, /120, /200, & /260 24 I/O channels, expandable up to 192 Connector: DB37 male, P2 Device: 82C55 Output Voltage Levels Minimum �…
-
31, Omega Engineering 100/200 Series OMB-DaqBook User’s Manual 01-23-02 DaqBook Hardware 3-15 A. Use the DBK Power Requirements Worktable to calculate the power requirements of your system’s DBK cards. B. Use the Available Power Chart to determine your system’s power availability. C. If the required power in step 5A is more than the available power in step 5B, you need an additional power card. There are two auxiliary power supply cards: • DBK32A – For use wi…
-
1, omega.com e-mail: [email protected] For latest product manuals: omegamanual.info Shop online at User’s Guide OMB-457-0906 rev 1.1 OMB-DAQBOOK 100 & 200 Series Data Acquisition for Notebook, Desktop, and Tower PCs
…
-
28, 3-12 DaqBook Hardware 01-23-02 OMB-DaqBook User’s Manual DaqBook/260 The DaqBook/260 is a combination of a DaqBook/200 and a DBK60 expansion chassis. The DaqBook sits on an upper shelf within the enclosure. Below it, a card drawer can hold three analog DBK cards and provide termination panels with connectors for various sensors. J1 J3 connects to P1 on by internal cable. DaqBook J3 P1 External DB37 To Sensors JP1 Pin 1 (+5V) Pins 2-37 JP2 DaqBook/260 Block Diagram 1 of 3 user-supplied DBK cards (all 3 must be all anal…
-
47, Omega Engineering 100/200 Series Appendix A – Specifications, DaqBooks 02-14-02 A-1 Specifications, DaqBooks A General Power Consumption DaqBook/100, & /120: 510 mA @ 12 VDC DaqBook /112: 360 mA @ 12 VDC DaqBook /200: 620 mA @ 12 VDC DaqBook /216: 600 mA @ 12 VDC DaqBook /260*: 620 mA @ 12 VDC *(Does Not Include internal DBK options) Operating Temperature: 0° to 50°C Storage Temperature: 0° to 70°C Humidi…
-
9, Omega Engineering 100/200 Series OMB-Daq Systems 10-29-02 Overview 1-3 DBK output signals can be bipolar, e.g., -5 to +5 V, or unipolar, e.g., 0 to 10 V. The user can select a range of relevant values to correspond to the lowest signal (e.g., -5 or 0 V) and the highest signal (e.g., 5 or 10 V) signal. This type of range selection guarantees the highest resolution in 12-bit or 16-bit conversion. DBK modules share the same footprint as the DaqBook and a typical notebook PCs; allowing for convenient stacking. The majority of these modules have their own …
-
7, OMB-Daq Systems 10-29-02 Overview 1-1 Daq Systems, a Brief Overview 1 Daq Systems, the Modular Concept …… 1-1 DaqBooks and DaqBoards …… 1-2 Using DBK Cards and Modules for Signal Conditioning ….. 1-2 Daq Software ……1-3 Daq Systems, the Modular Concept Daq equipment and software form a modular, interrelated family of products that provide great flexibility in data acquisition system design. This flexibility allows for the development of custom systems that are unique to the user, an…
-
51, WARRANTY/DISCLAIMER OMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and workmanship for a period of 13 months from date of purchase. OMEGA’s WARRANTY adds an additional one (1) mont h grace period to the normal one (1) year product warrant y to cover handling and shipping time. This ensures that OMEGA’s customers receive maximum coverage on each product. If the unit malfunctions, it must be returned to the factory for evaluation. OMEGA’s Customer Service Department will …
-
10, Omega Engineering 100/200 Series 1-4 Overview 10-29-02 OMB-Daq Systems Reference Notes: The software document modules, DaqView, DaqViewXL, and Post Acquisition Data Analysis User’s Guide, are not included as part of the hardcopy manual, but are available in PDF version. See the PDF Note, below. Programming topics are covered in the Programmer’s User Manual (p/n OMB-1008-0901). As a part of product support, this manual is automatically loaded onto your hard drive during sof…
-
36, pg. 2, OMB-DBK Basics 02-19-02 Daq Systems Reference Notes: During software installation, Adobe ® PDF versions of user manuals will automatically install onto your hard drive as a part of product support. The default location is in the Programs directory, which can be accessed from the Windows Desktop. Refer to the PDF documentation, especially the DBK Option Cards and Modules User’s Manual (p/n OMB-457-0905) for details regarding bot…
-
32, Omega Engineering 100/200 Series 3-16 DaqBook Hardware 01-23-02 OMB-DaqBook User’s Manual 11 – Connect internal signals Connect signal inputs from DBK cards to termination panels. DBK cards connect to the termination panels in various ways (see the following figure). Refer to the DBK options manual (p/n 457-0905) as needed. • Single-ended connections use analog common. • Differential connections require the proper polarity, typically red-to-red for high (+) and black-to-black for low (-). • For thermo…
-
19, OMB-DaqBook User’s Manual 01-23-02 DaqBook Hardware 3-3 Front and Rear Panels Excluding DaqBook/260 The following illustrations show the relative locations of connectors, power switches, indicator LEDs, and the expansion slot, as applicable. DaqBook/260 is treated separately in an upcoming section. Reference Note: DaqBook/260 users should refer to page 3-12 for information specific to that product. Front Panel of DaqBook/112/216 Re…
-
12, 2-2 Setup and Startup 10-29-02 OMB-DaqBook User’s Manual (1) Set Jumpers (a) Place the unit on a flat, stable surface. Ensure no power or signal lines are connected. (b) Remove cover screw(s), and slide the top cover plate free of the device. All jumpers are accessible from above the board, and no further disassembly is required. (c) Set jumpers JP1 through JP4 as needed for your application. Jumper configuration options follow shortly. Note that jumpers are clearly labeled on…
-
43, Daq Systems 02-19-02 OMB-DBK Basics, pg. 9 Calculating Your System’s Power Needs Use the chart below and the worktable on the next page to ensure your system will have sufficient power. If the load (calculated in the worktable) exceeds available power (from the chart at the right), you must add a power card or a module such as a DBK32A or DBK33. Available Power Chart—Supply Product Available Power LogBook +5 VDC @ 0.10 A from P1-1, P2-18, P2-20, P3-20…
-
44, pg. 10, OMB-DBK Basics 02-19-02 Daq Systems DBK Power Requirement Worktable—Demand DBK Voltage Reference Calculation Options +15 VDC -15 VDC +5 VDC Quantity × mW = Sub Total DBK1 0 0 0 0 DBK2 18 mA 18 mA 5 mA 565 DBK4 95 mA 80 mA 25 mA 2750 DBK5 2 mA 2 mA 15 mA 135 DBK7 14 mA 8 mA 18 mA 420 DBK8 15 mA 15 mA <1 mA 455 DBK9 21 mA 16 mA <1 mA 560 DBK11A 0 0 0 0 DBK12 15 mA 1…
-
26, 3-10 DaqBook Hardware 01-23-02 OMB-DaqBook User’s Manual DaqBook P2 Pinout Digital I/O This P2 interface is available on the DaqBook/100, /120, /200, and /260. 1 9 G N D P O R T A 0 3 7 P O R T A 1 3 6 P O R T A 2 3 5 P O R T A 3 3 4 P O R T A 4 3 3 P O R T A 5 3 2 P O R T A 6 3 1 P O R T A 7 3 0 P O R T C 0 2 9 P O R T C 1 2 8 P O R T C 2 2 7 P O R T C 3 2 6 P …
-
39, Daq Systems 02-19-02 OMB-DBK Basics, pg. 5 1. The end use of the acquisition data should be used to determine how you set up and program your acquisition system. Prior to creating the system you should understand its layout and know how you are going to assign the channels. If you can answer the following questions you are off to a good start. If not, you need to find the answers. • What engineering units, ranges, sampling rates, etc. are best for your data? • Will the data b…
-
2, Omega Engineering 100/200 Series Servicing North America: U.S.A.: One Omega Drive, P.O. Box 4047 ISO 9001 Certified Stamford, CT 06907-0047 TEL: (203) 359-1660 FAX: (203) 359-7700 e-mail: [email protected] Canada: 976 Bergar Laval (Quebec) H7L 5A1, Canada TEL: (514) 856-6928 FAX: (514) 856-6886 e-mail: [email protected] For immediate technical or application assistance: U.S.A. and Canada: Sales Service: 1-800-826-6342 / 1-800-TC-OMEGA ® Customer Service: 1-800-622-2378 / 1-800-622-BEST ® Engineering Service: 1-800-872-9436 / 1-800-USA-WHEN ® Mexico: En Espan˜ol: (001) 2…
-
22, 3-6 DaqBook Hardware 01-23-02 OMB-DaqBook User’s Manual Bipolar or Unipolar A/D Operation (JP3)* *Hardware Setting For DaqBook/100, DaqBook /112, and DaqBook /120 Only The A/D converter in the DaqBook can be operated in two modes, bipolar or unipolar. In the bipolar mode (default setting), input voltages up to ±5 VDC can be applied (on the ×1 gain range). In the unipolar mode, positive voltages up to 1…
-
18, 3-2 DaqBook Hardware 01-23-02 OMB-DaqBook User’s Manual Performance Factors DaqBooks are flexible when it comes to analog input capabilities. The A/D maximum sample rate is 100 kHz (divide by number of channels for scan rate) with a 16-channel multiplexer and a programmable- gain input amplifier. Users can expand channel capacity to 256 analog inputs via expansion modules for multiplexing RTDs, thermocouples, strain gages, anti-aliasing filters, and simul…
-
29, OMB-DaqBook User’s Manual 01-23-02 DaqBook Hardware 3-13 The rear panel is made of three termination panels with connectors for the various sensors. Hardware Setup WARNING Electrical Shock Hazard! To avoid injury or equipment damage, turn off power to all connected equipment during setup. CAUTION Use ESD tools, containers, and procedures during setup of DBK cards. Electrostatic discharge can damage some of the components. To prevent pin damage…
-
25, OMB-DaqBook User’s Manual 01-23-02 DaqBook Hardware 3-9 DaqBook P1 Pinout Analog I/O (compatible with Metrabyte DAS-16) 1 9 L L S E N S E G N D C H 0 H I I N 3 7 C H 1 H I I N 3 6 C H 2 H I I N 3 5 C H 3 H I I N 3 4 C H 4 H I I N 3 3 C H 5 H I I N 3 2 C H 6 H I I N 3 1 C H 7 H I I N 3 0 L L G N D 2 9 L L G N D 2 8 D / A 1 O U T 2 7 S S H / D / A 1 R E F I N 2 6 I P 0 / T R I G 0 2 5 I P 2 / C T R 0 G A T E 2 4 0 P 0 / C …
-
34, 3-18 DaqBook Hardware 01-23-02 OMB-DaqBook User’s Manual Using T-Cables CAUTION Turn power OFF to the Daq devices and externally connected equipment while connecting cables and setting configuration jumpers and switches or before opening the lid. Electrical shock or damage to equipment can result even under low-voltage conditions. T-Cables are available in different lengths and can be used for linking two or more compatible devices together via the device’s 37-pin digital I/O conne…
