DBL Technology GoIP Operation & User’s Manual

Operation & User’s Manual for DBL Technology GoIP Gateway (63 pages)

Specifications:

777/777563-goip.pdf file (30 Nov 2023)
  • Manufacturer: DBL Technology
  • Category of Device: Gateway
  • Document: GoIP, File Type: PDF Operation & User’s Manual
  • Updated: 30-11-2023
  • Count of Pages: 63
Download GoIP Manual (63 pages)

Read DBL Technology GoIP Document Online:

Data: UPD 30th November 2023

DBL Technology GoIP Gateway PDF Operation & User’s Manual (Updated: Thursday 30th of November 2023 08:18:23 PM)

Rating: 4.5 (rated by 40 users)

Compatible devices: Meraki Go, HG-3000, InfinityLink ILC410, e-2-s, GoIP-1, CMD300, DLOS8, AR-727.

Recommended Documentation:

Text Version of DBL Technology GoIP Operation & User’s Manual (Summary of Contents)

(Ocr-Read of the DBL Technology GoIP Document (Main Content), UPD: 30 November 2023)
  • 1, DBL Technology GoIP GoIP User Manual http://www.dbltek.com Sales: [email protected] Support: [email protected] GoIP User Manual VoIP GSM Gateways -Models- GoIP GoIP-4/4I GoIP-8/8I GoIP-16 GoIP-32 Revision: 1.4B 2014/3/04 …

  • 2, GoIP User Manual http://www.dbltek.com 1 Content 1 General............................................................................................................................................................ 3 1.1 Introduction.......................................................................…

  • 3, GoIP User Manual http://www.dbltek.com 2 3.4.9 Reboot..............................................................................................................................................52 Appendix A. Special SMS Commands.........................................................................…

  • 4, GoIP User Manual http://www.dbltek.com 3 1 General 1.1 Introduction GoIP is the abbreviated from GSM over IP. It is a new type of VoIP gateway that allows call terminations from a VoIP network to a GSM network and vice versa. Call connections between IP networks and GSM networks are now bridged seamles…

  • 5, GoIP User Manual http://www.dbltek.com 4 1.2 Protocols  TCP/IP V4 (IP V6 automatic adaptive)  Dual VoIP protocols: ITU-T H.323 V4, IETF SIP V2.0  Multiple Codecs: ITU-T G.711 Alaw/ULaw, G.729A, G.729AB, G.723.1 and GSM  H.2250 V4  H.245 V7  H.235 (MD5, HMAC-SHA1)  RFC188…

  • 6, DBL Technology GoIP GoIP User Manual http://www.dbltek.com 5  Call Management and Routing 1.5 Package Content Use care when unpacking the device package in order to avoid damage to the main unit and the packing materials. Retain the packing materials in case the unit is to be transported in the future. Please insp…

  • 7, DBL Technology GoIP GoIP User Manual http://www.dbltek.com 6 2. AC/DC Power Adapter:  GoIP1: 12V/500mA  GoIP4: 12V/2A  GoIP8: 12V/3A  GoIP16: 12V/4A  GoIP32: 12V/4.5A 3. 1 x Ethernet CAT5 Cable (2M) 1.6 LED Indicators LED indicators (shown above for GoIP-8) are used to show the current status of the …

  • 8, DBL Technology GoIP GoIP User Manual http://www.dbltek.com 7 Channel “x” Each GSM channel has its own status LED and its color is green. 1. It blinks at a rate of every 100ms (Fast blink) when the corresponding GSM channel is not yet registered to a GSM network. 2. It blinks at a rate of every second (Slow blink) when th…

  • 9, GoIP User Manual http://www.dbltek.com 8 2. The LAN port is intended for intranet or internet connection. Depending on your network environment, it can be connected various type of network equipment, such as network router, network switch / Hub, xDSL/Cable modem, etc. 3. The PC port is intended for…

  • 10, DBL Technology GoIP GoIP User Manual http://www.dbltek.com 9 3 Configuration The device can be configured via its built-in http web server or via an Auto Provision Server. Auto Provision Server is a free utility supporting both Window and Linux OS. This utility is developed by DBL Technology for the sole purpose of automating the …

  • 11, GoIP User Manual http://www.dbltek.com 10 3.2 Status There are four pages under the Status category and they are Summary, General, GSM, and SIM Call Forward. Each page is refreshed every 5 seconds; however, this feature is not supported when the Firefox browser is used. Sample pages shown in this section ar…

  • 12, DBL Technology GoIP GoIP User Manual http://www.dbltek.com 11 d. DIALING <phone number> - This occurs when the GoIP is dialing out a phone number via the corresponding GSM channel or The DIALING status shows that a number is being dialed out via the corresponding GSM channel or a VoIP line. The phone number dialed is a…

  • 13, GoIP User Manual http://www.dbltek.com 12 a) S/N – This field shows the serial number of the device. b) Firmware – This field shows the current firmware version. c) Model – This field shows the model number of the device d) Local Time - This shows the current system time. It is a good indication for no…

  • 14, GoIP User Manual http://www.dbltek.com 13 3.2.3GSM The GSM page shows the current GSM channels status and information on the GSM modules and the SIM cards inserted. The top table shows a number of GSM parameters which are useful to determine if the GSM channels in the gateway are working properl…

  • 15, GoIP User Manual http://www.dbltek.com 14 1. Module - The model number of the GSM module. 2. Firmware Ver - The version number of the firmware installed in the module. 3. SIM Number - The GSM number that is assigned to the SIM card. User must enter this number manually. 4. IMEI - International Mobile Station E…

  • 16, DBL Technology GoIP GoIP User Manual http://www.dbltek.com 15 3.3 Configuration Click “Configuration” on the left hand column to display the Configuration page and the following submenu. 1. Preference 2. Network 3. Basic VoIP 4. Advance VoIP 5. Media 6. Call Out 7. Call Out Auth. 8. Call In 9. Call In Auth. 10. …

  • 17, GoIP User Manual http://www.dbltek.com 16 3.3.1Preference The preference page shown above consists of the following system level parameters and options as shown in the table below. Parameter (Preference) Description Default Value 1. Language This sets the webpage and voice prompts language. Currently, only En…

  • 18, GoIP User Manual http://www.dbltek.com 17 4. Auto-provision  Provision Server  Provision Interval The auto provision is optional. When this option is enabled, the device downloads its configuration from the Auto Provision Server at start up or at the time interval specified by the Provision Interval. T…

  • 19, DBL Technology GoIP GoIP User Manual http://www.dbltek.com 18 9. Auto Reboot  Reboot Time This option allows the device to reboot itself at the time defined by Reboot Time. This parameter specifies the time to reboot the device. Two formats are supported: 1. HH:MM - When this is specified with a valid 24-hr time format (00:…

  • 20, GoIP User Manual http://www.dbltek.com 19 traffics for the device installed when all lines are used simultaneously. In order to get external network access, the LAN port must be configured according to the network environment to be connected. LAN Port There are 3 access methods available to configure the LAN po…

  • 21, GoIP User Manual http://www.dbltek.com 20 protocol supported is PPTP with no encryption or 40-bit encryption which is defined on the VPN server. In general, this option is used to avoid VoIP blockings. 3.3.3Basic VoIP The GoIP can support both SIP and H.323 VoIP protocols. For GoIP-1, both protocol …

  • 22, DBL Technology GoIP GoIP User Manual http://www.dbltek.com 21 a) All Routing Prefixes are set - Try to match the number received for making an outgoing call against the Routing Prefix of each channel. If only one match is found, the corresponding channel is used to make the outgoing call. If more than one matches are…

  • 23, GoIP User Manual http://www.dbltek.com 22 7. Re-register Period (s) Register to the SIP Server at an interval specified by this parameter. 60 8. Outbound Proxy The address of the Outbound Proxy used for VoIP communication is specified here. 9. Home Domain Home Domain is used in SIP identification. It should be …

  • 24, DBL Technology GoIP GoIP User Manual http://www.dbltek.com 23 When a GSM channel receives an incoming call, the call can either be answered by the device or forwarded to a SIP extension or IVR. For more details, please see Section 3.3.8 for Call In configuration. Please note that the parameters defined in this mode are for …

  • 25, GoIP User Manual http://www.dbltek.com 24 4. Trunk Gateway Mode (for all models except GoIP-1) This mode offers a seamless interface with the SIP Trunk configuration in a SIP server. In general, SIP registration is not required in this mode; this is an advantage for a SIP system that requires a license per regist…

  • 26, GoIP User Manual http://www.dbltek.com 25 Gateway3) specified and then dial out the call via an Idle channel that is used the least (in terms of the number of calls dialed). The last part of the SIP Trunk Gateway IP addresses can be specified as "X" or "x" to represent that the wh…

  • 27, GoIP User Manual http://www.dbltek.com 26 The table below summaries all the parameters defined in this section. Parameter (Advanced VoIP) Description Default Value 1. SIP Listening Port Mode  Port Number SIP Local port defines the network port number that the device listens for incoming SIP messages…

  • 28, GoIP User Manual http://www.dbltek.com 27 receive audio packets. Since it may take a few to over 10 seconds for a ringback tone is returned from the GSM network, the caller may hear a long silent period 3. Call OUT Auth. Mode This setting defines how incoming VoIP calls are authenticated when the devic…

  • 29, DBL Technology GoIP GoIP User Manual http://www.dbltek.com 28 9. Signaling NAT Traversal This setting is not required if the target SIP server / PBX supports NAT traversal. However, if your ISP blocks VoIP traffics, you could try to use Relay Proxy setting. Depending on how your ISP blocks VoIP traffics, the Relay Ser…

  • 31, GoIP User Manual http://www.dbltek.com 30 3.3.6Media This section allows the user to program various settings for media (voice) transmission and format. Depending on your network environment and condition, you may or may not need to change these settings. Please see the parameter table below for…

  • 32, DBL Technology GoIP GoIP User Manual http://www.dbltek.com 31 3. Jitter Buffer  Delay  Min. Delay (ms)  Max. Delay (ms) A jitter buffer is designed to remove the effects of jitter from the decoded voice stream, buffering each arriving packet for a short interval before playing it out. This substitutes additional delay a…

  • 33, GoIP User Manual http://www.dbltek.com 32 5. G.729AB (with Silence Compression and Voice Activity Detection (VAD) 8K ~39K 6. G.723.1 5.3K / 6.4K ~26K / 27K Note: Time per packet = 30ms is used for all bandwidth calculations. For more calculations with other conditions, please visit the VoIP…

  • 34, GoIP User Manual http://www.dbltek.com 33 3.3.7Call OUT The Call Out page defines how each GSM channel handles calls when they are routed from VoIP. This section MUST Be defined properly in order to enable each GSM channel to dial out calls based on your requirements. In general, you can achieve the followings…

  • 35, GoIP User Manual http://www.dbltek.com 34 in this case. Please note that how this line is selected depends on the Config Mode and the Callee Number received. The Callee Number is defined as the phone number specified in the “To:” field of an INVITE message. Please refer to Section 3.3.3.1 for more informat…

  • 36, GoIP User Manual http://www.dbltek.com 35 then append “86” to the beginning of the number. If the Callee Number is 913601234567, the actual number dialed is 8613601234567. 5. Restricted Dial Plan This option forces the GoIP to only dial out the phone numbers that match the rules defined in the dia…

  • 37, DBL Technology GoIP GoIP User Manual http://www.dbltek.com 36 3.3.9Call IN This page defines how incoming calls to each GSM channel are handled. GSM incoming calls can either be answered and prompted for second dial or forwarded to a phone extension or IVR in the VoIP network connected. The parameters in the Call In Page are divide…

  • 38, GoIP User Manual http://www.dbltek.com 37  CID Prefix 1. Disabled – Incoming GSM caller ID is not transmitted to SIP. 2. Use Remote Party ID – This enables the Remote-Party-ID field is sent as part of the INVITE message. The incoming GSM caller ID is specified as part of this field. 3. Use …

  • 39, DBL Technology GoIP GoIP User Manual http://www.dbltek.com 38 When there is no match, the incoming GSM call is handled as if the Forward Number is blank. 4. Dial Plan The Dial Plan specifies rules to process a number dialed after the call is answered. This number is referred as a second dial number. This enables a…

  • 40, GoIP User Manual http://www.dbltek.com 39  Backup Host Address  Host Address incoming calls. If it is set to Busy, then the Host channel will always to be used to answer an incoming call whenever it is available. Setting this parameter enables Hunt Group Sharing feature. This parameter must…

  • 41, DBL Technology GoIP GoIP User Manual http://www.dbltek.com 40 4. Whitelist + Password – Both Whitelist and password are used to authenticate incoming GSM calls. 5. Blacklist – Calls with caller IDs that are listed on the Blacklist are not answered by the channel selected. 2. Whitelist / Blacklist Call screen list c…

  • 42, DBL Technology GoIP GoIP User Manual http://www.dbltek.com 41 The parameters for this section are described in details in the table below. Parameter (SIM Card) Description Default Value 1. GPRS Registration This enables the GPRS registration mode for all GSM channels. Enable 2. SIP Registration when Talk Time Limit …

  • 43, GoIP User Manual http://www.dbltek.com 42 10. Billing Increment (s) This is a call duration measurement unit expressed in seconds. Depending on your service provider, some services are measured and billed in sixty second increments (one minute) or the billing increment may be in durations of six or even ten secon…

  • 44, GoIP User Manual http://www.dbltek.com 43 1. Unconditional Call Forward  Forward Num Forward all incoming calls unconditionally to the number specified. This specifies the phone number to receive forwarded calls under this condition. Not Set 2. Call Forward Busy  Forward Num Forward calls when the…

  • 45, DBL Technology GoIP GoIP User Manual http://www.dbltek.com 44 3.3.14 SMS This page covers parameters that are related to SMS. The top parameter (SMS to VoIP) is a general setting for all channels. This defines how received SMS messages are used for Call Back or Forward functions which are described in details in the…

  • 46, GoIP User Manual http://www.dbltek.com 45 Next, the parameters defined below are channel dependent. Please make sure that the desired channle is selected before making changes. Parameter (SIM Card) Description Default Value 1. SMS Server  SMS Server IP  SMS Server Port  SMS Client I…

  • 47, DBL Technology GoIP GoIP User Manual http://www.dbltek.com 46 The *Auto Config. Other Line button is provided to facilitate the programming of each channel. After the parameters for the CH1 SIM are set, clicking this button automatically duplicates the same settings to all other channels with the exception that the SMS C…

  • 48, DBL Technology GoIP GoIP User Manual http://www.dbltek.com 47 Three modes for base station selection are available: 1.Auto - This mode uses the default GSM base selection mechanism. 2.Poll - This mode limits the number and the list of base stations (BTS) that could be selected. Either Whitelist or Blacklist method can be used…

  • 49, DBL Technology GoIP GoIP User Manual http://www.dbltek.com 48 3.4 Tools Click “Tools” on the left hand menu to access the submenu as shown below. Please note the available options under the Tools menu. 3.4.1Online Upgrade Click [Online Upgrade] to upgrade the device firmware. The current version is displayed as well as the …

  • 50, GoIP User Manual http://www.dbltek.com 49 Contact us or your local agent/supplier for the latest firmware version. Enter the firmware link (URL) and then click “Start” to begin firmware upgrade. Once the firmware upgrade is completed, the device will reboots itself automatically. Please wait patient…

  • 51, DBL Technology GoIP GoIP User Manual http://www.dbltek.com 50 The procedures to send an USSD command are: a) Select the Line (GSM channel) that you want to send an USSD command to the service provider. The line status and the SIM (GSM) number are displayed. The last option "All Lines" means that all chann…

  • 52, DBL Technology GoIP GoIP User Manual http://www.dbltek.com 51 . The procedures to send a SMS are: a) Select the Line (GSM channel) that you want to send a SMS. The line status and the SIM (GSM) number are displayed. The last option "All Lines" means that all channels are selected and the same SMS is sent…

  • 53, DBL Technology GoIP GoIP User Manual http://www.dbltek.com 52 3.4.7Backup / Restore The device configuration can be backup or restore via this page. Click [Backup / Resotre Confguration] to access the page shown below. To backup the device configuration, just click [Save] in the Backup Configuration section. If a password is require…

  • 54, DBL Technology GoIP GoIP User Manual http://www.dbltek.com 53 3.4.9 Reboot Click [Reboot] to restart the device. Click [OK] in the pop up window shown below to confirm this action. The reboot process will take couple of mins. …

  • 55, GoIP User Manual http://www.dbltek.com 54 Appendix A. Special SMS Commands In order to manage the device, special SMS commands can be sent to anyone of the GSM channel in order to read the LAN IP, reset the device and reboot the device. The table below summarizes the SMS command syntax. “<” and “>” …

  • 56, GoIP User Manual http://www.dbltek.com 55 Appendix B. SMS To VoIP The device receives SMS messages from both GSM and VoIP networks and they are handled according to the modes defined below. 1. Call Function – In this mode, a received SMS is used to implement the “Call Back” function. The …

  • 57, GoIP User Manual http://www.dbltek.com 56 the Call OUT via GSM parameter of the device must be enabled and the Forward Number associated with this parameter is set to the phone number of the SMS sender. To achieve the Call Back function, the SIP server calls the called party via its phone network and the…

  • 58, GoIP User Manual http://www.dbltek.com 57 Allow: INVITE, ACK, BYE, CANCEL, OPTIONS, NOTIFY, REFER, REGISTER, MESSAGE, INFO, SUBSCRIBE Content-Type: application/sdp Content-Length: 226 2. Forward Function – This mode supports SMS forwarding from GSM to SIP and from SIP to GSM. a) Received GSM SMS messages are fo…

  • 59, GoIP User Manual http://www.dbltek.com 58 format. The first line must contain a valid GSM number and then the text message begins at the second line and must meet the restrictions imposed by a normal GSM SMS. A sample of a SIP MESSAGE sent from SIP device is shown below. Example: A SIP SMS is sent…

  • 60, GoIP User Manual http://www.dbltek.com 59 Appendix C. Custom Network Tones This section describes how to define custom network tones. The “Custom” selection allows the following tones to be defined as shown on the right. 1. Dial Tone – When an incoming call is answered, this tone is generated to indicate to…

  • 61, DBL Technology GoIP GoIP User Manual http://www.dbltek.com 60 Appendix D. GSM Group Mode The GSM Group mode is designed to simulate the function of one GSM number with multiple lines. The idea is to form a GSM group with one number being the "Server". Only this GSM number is announced to the public. Calls to this …

  • 62, GoIP User Manual http://www.dbltek.com 61 Appendix E. CID Call Forward For incoming GSM calls, the phone number of the caller can be displayed at the called party (SIP terminal). The device supports the following two methods. Unfortunately, not all SIP servers support one or both methods. Pleas…

  • 63, GoIP User Manual http://www.dbltek.com 62 Appendix F. Volume Adjustment The volume adjustment of the device can be accessed via the URL below. http://<device address>/en_US/gaim.html The <device address> is the IP address or domain name of the device. The volume levels of the audio streams from …

DOC-2edc963d:

Recommended:
GLC3630L20, 2000, STERILIZERUV AS-5W, 40732-17-16

Additional Information:
# Brand Model Document Type/File Pages File Size Last Checked
1 THOMSON
TG784-SIP
946 2.99 Mb 13/10
2 Draytek
Vigor3900
30 0.84 Mb 14/11
3 HRW
HPE-BNMBUS
24 03/12
4 C-Bus
5200PG
50 23/10
5 OpenVox
DGW-100XR
60 27/09
6 Sercomm
NA503S-4G
10 28/10
Product Types by DBL Technology:

Popular Right Now:

# Brand Model Document (PDF) Pages Size Check Date
1 Sanyo
VM-PS12
16 16.09.2023
2 Epson
AcuLaser MX20DN series
2 1.77 Mb 26.11.2023
3 Whirlpool
3RLER5437KQ0
6 0.56 Mb 23.11.2023
4 Samsung
J1455AV
22 0.42 Mb 07.09.2023
5 Bazooka
RSW1024
8 0.52 Mb 26.10.2023
6 HP
DL974B
4 21.08.2023
7 HHB
DRM85
2 0.49 Mb 02.10.2023
Operating Impressions, Questions and Answers: