Teltonika FMB110 Manual 

2, 2 FMB110 | Wiki Table of Contents Know your device .......................................................................... 3 Pinout ................................................................................................. 4 Wiring scheme ................................................................................... 5 Set up your device ............................................................…

4, 4 FMB110 | Wiki Pinout Table 1 FMB110 2x6 socket pinout Pin number Pin name Description 1 VCC (10-30)V DC (+) Power supply (+10-30 V DC). 2 AIN 1 Analog input, channel 1. Input range: 0- 30 V DC. 3 AIN 2 / DIN 3 Analog input, channel 2. Input range: 0- 30 V DC / Digital input, channel 3. 4 DIN 2 Digital input, channel 2. 5 DIN 1 Digital input, channel 1. 6 INPUT 6 TX EXT (LVCAN – TX). 7 GND (-) Digital output, channel 1. Open collector output. Max. 3,3 A DC. 8 DOUT 1 Digital output, channel 1. Open collector…

5, 5 FMB110 | Wiki Figure 3 FMB110 Wiring scheme Wiring scheme 1 Automotive relay 1 …

6, Teltonika FMB110 6 FMB110 | Wiki Set up your device How to insert Micro-SIM card 1. Gently remove FMB110 cover using plastic pry tool from both sides. 2. Insert Micro-SIM card as shown with PIN request disabled or read our Wiki how to enter it later in Configurator. Make sure that Micro-SIM card cut-off corner is pointing forward to slot. 3. Attach device cover back. 4. Device is ready to be connected. Figure 4 Cover removal Figure 5 Micro-SIM card insert Figure 6 Attaching cover back Figure 7 Device is ready …

7, Teltonika FMB110 7 FMB110 | Wiki PC Connection (Windows) 1. Power-up FMB110 with DC voltage (10 – 30 V) power supply using supplied power cable. LED’s should start blinking, see “LED indications”. 2. Connect device to computer using Micro-USB cable or Blue- tooth connection: • Using Micro-USB cable ▬ You will need to install USB drivers, see “How to install USB drivers (Windows)” • Using Blue-tooth �…

8, 8 FMB110 | Wiki Configuration process begins by pressing on connected device (Figure 9 Device connected via USB). After connection to Configurator Status window will be displayed (Figure 10 Configurator Status window). Various Status window tabs display information about GNSS, GSM, I/O, Maintenance and etc. FMB110 has one user editable profile, which can be loaded and saved to the device. After any modification of configuration the changes need to be saved to device using S…

9, Teltonika FMB110 9 FMB110 | Wiki Mounting recommendations • Connecting wires ▬ Wires should be connected while the module is not plugged in. ▬ Wires should be fastened to stable wires or other non- moving parts. Any heat emitting and/or moving objects should be kept away from the wires. ▬ There should be no exposed wires. If factory isolation was removed while connecting the wires, the isolation material should be applied. ▬ If the wires are placed in the exterior or in places whe…

10, 10 FMB110 | Wiki LED indications Table 3 Navigation LED indications Behaviour Meaning Permanently switched on GNSS signal is not received Blinking every second Normal mode, GNSS is working Off GNSS is turned off because: Device is not working or Device is in sleep mode Blinking fast constantly Device firmware is being flashed Table 4 Status LED indications Behaviour Meaning Blinking every second Normal mode Blinking every two seconds Sleep mode Blinking fast for a short time Modem activity Off Device is not working or D…

11, 11 FMB110 | Wiki Power Input voltage range 10 - 30 V DC with overvoltage protection Power consumption At 12V < 5 mA (Ultra Deep Sleep) At 12V < 6 mA (Deep Sleep) At 12V < 7 mA (Online Sleep) At 12V < 17 mA (GPS Sleep) At 12V < 35 mA (nominal) Blue-tooth Specification 4.0 + LE Supported peripherals Temperature and Humidity sensor, Headset, OBDII dongle Interface Digital Inputs 3 Digital Outputs 2 Analog Inputs 2 LV-CAN Inputs 1 1-Wire 1 GNSS antenna Internal High Gain GSM an…

12, 12 FMB110 | Wiki Electrical characteristics Table 6 Electrical characteristics Characteristic description Value Min. Typ. Max. Unit Supply Voltage Supply Voltage (Recommended Operating Conditions) +10 +30 V Digital Output (Open Drain grade) Drain current (Digital Output OFF) 120 µA Drain current (Digital Output ON, Recommended Operating Conditions) 0.1 0.5 A Static Drain-Source r…

13, 13 FMB110 | Wiki Safety information This message contains information on how to operate FMB110 safely. By following these requirements and recommendations, you will avoid dangerous situations. You must read these instructions carefully and follow them strictly before operating the device! • The device uses SELV limited power source. The nominal voltage is +12 V DC. The allowed voltage range is +10..+30 V DC. • To avoid mechanical damage, it is advised to trans…

14, 14 FMB110 | Wiki Certification and Approvals • FMB110 EAC • FMB110 REACH • FMB110 Declaration of IMEI assignment This sign on the package means that it is necessary to read the User‘s Manual before your start using the device. Full User‘s Manual version can be found in our Wiki. This sign on the package means that all used electronic and electric equipment should not be mixed with general household waste. …