-
1, PRINTED IN JAPAN TOSHIBA REMOTE RECEIPT PRINTER TRST-A10 SERIES Document No. EO10-13009A Original Nov., 2007 (Revised Feb., 2008) Product Descri p tion
…
-
2, Toshiba TRST-A10 SERIES EO10-13009A TABLE OF CONTENTS Page 1. OUTLINE -------------------------------------------------------------------------------------------------1- 1 1.1 FEATURES OF THE PRINTER -----------------------------------------------------------------------1- 1 1.2 DESCRIPTION OF MODEL NUMBER --------------------------------------------------------------1- 2 1.3 OVERVIEW AND DIMENSIONS ---------------------…
-
3, Toshiba TRST-A10 SERIES 1. OUTLINE EO10-13009A 1.1 FEATURES OF THE PRINTER 1-1 1. OUTLINE 1.1 FEATURES OF THE PRINTER 1) This printer is a single station printer for 80 mm width receipt and is equipped with the RS-232C serial interface, USB interface or parallel interface (option), conforming to the ESC/POS commands. 2) Paper drop-in mechanism realizes easy paper loading and head cleaning. When setting or replacing the paper roll, only load it into the printer and close the cover. 3) This printer performs in thermal direct method at high spe…
-
4, 1. OUTLINE EO10-13009A (Revision Date: Feb. 06, 2008) 1.2 DESCRIPTION OF MODEL NUMBER 1-2 1.2 DESCRIPTION OF MODEL NUMBER Model name description TRST-A1 - - - …
-
5, 1. OUTLINE EO10-13009A 1.3 OVERVIEW AND DIMENSIONS 1-3 1.3 OVERVIEW AND DIMENSIONS 1.3.1 Front View/Rear View 1.3.2 Connectors 1 [DC24V] (Socket connector) The built-in AC adapter supplies +24V power to the printer through this connector. Do not connect anything other than the Toshiba TEC Specified AC adapter. 2 [Serial interface connector] An interface cable which connects the printer to a POS terminal or Personal Computer is connected to this co…
-
6, 1. OUTLINE EO10-13009A 1.3 OVERVIEW AND DIMENSIONS 1-4 3 [USB interface connector] An interface cable which connects the printer to a POS terminal or Personal Computer is connected to this connector, a USB I/F (V2.0 Full Speed) is needed for this connector. 4 [Drawer interface Connector] [CDKO] (6 pin modular connector) A drawer cable which connects the printer to a drawer is connected to this connector. To this connector, a Toshiba drawer can be connected. Do not connect anything other than the connectable drawer. 5 [Parallel …
-
7, 1. OUTLINE EO10-13009A 1.3 OVERVIEW AND DIMENSIONS 1-5 Error Status Table Green LED Blinking (Slow) Problem What to Do Where to Go Receipt paper is low* There are about 4 ½ meters, ± 3 meters, (15 feet, ± 10 feet) of paper left. Change the paper soon to avoid running out of paper part way through a transaction. Green LED Blinking (Fast) Problem What to Do Where to Go Receipt paper is out Change the paper now. Do not run a transaction without paper as…
-
8, 1. OUTLINE EO10-13009A 1.3 OVERVIEW AND DIMENSIONS 1-6 1.3.4 Datascope Mode Datascope Mode allows the user to test the printer’s communications. When in Datascope Mode the printer receives all communications, but instead of executing the commands it prints them out on receipt paper as hexadecimal numbers in the order received. For example, the ASCII character “A” is printed as the hexadecimal number 41 an so on. To run the Datascope Mode: After you have enabled the Data sc…
-
9, 1. OUTLINE EO10-13009A 1.4 SYSTEM CONFIGURATION 1-7 1.4 SYSTEM CONFIGURATION Serial or Parallel Interface Drawer Interface (Drawer Kick Specification) DC 24V TOSHIBA TEC DRAWER (DRWST-51A-8MVG-QM-R,etc.) POS Terminal (ST-A10 series, etc.) AC Adapter
…
-
10, 1. OUTLINE EO10-13009A (Revision Date: Feb. 06, 2008) 1.5 BASIC SPECIFICATIONS 1-8 1.5 BASIC SPECIFICATIONS Item Description Printing method Line thermal dot printing method Printing width (Font Size 1) 80 mm (576 dots) 58 mm (432 dots) (Font Size 2) 80 mm (560 dots) 58 mm (424 dots) Resolution 203.2 dpi x 203.2dpi Printing speed Max. 9 ips max (225 mm/sec) for 75W, 55W mode 2 color printing Max 50 mm/s…
-
11, 1. OUTLINE EO10-13009A 1.6 ELECTRONIC SPECIFICATIONS 1-9 1.6 ELECTRONIC SPECIFICATIONS 1.6.1 CPU ............................... UP0703111A 1.6.2 Serial Interface (RS232) 1. Specification (1) Synchronization method: Asynchronous (2) Baud rate: 9600, 19200, 38400,57600,115200 BPS (selectable) (3) Transmission parameter: Start bit: 1 bit Word length: 7 bit or 8 bit (selectable) Parity: None, even, odd (selectable) Stop bit: 1,2 bits selectable (4) Signal level: Transmitter: MARK = “1” (-5…
-
12, 1. OUTLINE EO10-13009A 1.6 ELECTRONIC SPECIFICATIONS 1-10 RS232 9 Pin to 9 Pin Cable 9 Pin Female 9 Pin Female 1 DCD DCD 1 2RxD RxD 2 3TxD TxD 3 4DTR DTR 4 5 LGND LGND 5 6DSR DSR 6 7RTS RTS 7 8CTS CTS 8 9 SHLD SHLD 9 Applicable connector: D-sub connector Printer side: 1002-09MS4G-L (CHUFON or equivalent) Cable side: DB9 RS232 F/F serial cable NOTE: The RS-232C signal is according to EIA RS-232C. 3. I/…
-
13, Toshiba TRST-A10 SERIES 1. OUTLINE EO10-13009A 1.6 ELECTRONIC SPECIFICATIONS 1-11 (4) DSR When the DTR/DSR control is selected, the printer confirms this signal is SPACE and then sends the status data. When it is not selected, the data is sent without DSR. (5) SG Signal ground. (6) CTS Clear to send. This is asserted by host terminal to acknowledge RTS and allow printer to transmit. Pin 2 - Transmitted Data (TxD) This signal is active when data is transmitted from the DTE (computer) device to the DCE (printer)device. When no data is transmitte…
-
14, Toshiba TRST-A10 SERIES 1. OUTLINE EO10-13009A 1.6 ELECTRONIC SPECIFICATIONS 1-12 4. Error detection If a parity error, framing error, and overrun error is detected, the data is stored into the buffer as “? (1) Framing error: This error occurs when no stop bit is found in the frame. The data is stored into the buffer as “?”. (2) Parity error: When an error is detected at the parity check, the data is stored into the buffer as “?”. (3) Overrun error: When this error is detected, the data is stored into the buffer as “?”. 5. Rece…
-
15, 1. OUTLINE EO10-13009A 1.6 ELECTRONIC SPECIFICATIONS 1-13 5Kohm DTR (RxIN) DSR, DCD (RxOUT) 5Kohm TxD (RxIN) RxD (RxOUT) 5Kohm RTS ( RxIN ) CTS (RxOUT) RxD (TxOUT) TxD (TxIN) DSR,DCD ( TxOUT ) DTR (TxIN) CTS (TxOUT) RTS (TxIN) 7. Electric specification For RS232, SP3243E or equivalent Input signal (RxD, DSR, CTS) [ Printer side ] [ Host side ] Where x denotes 1, 2…
-
16, 1. OUTLINE EO10-13009A 1.6 ELECTRONIC SPECIFICATIONS 1-14 1.6.3 USB Interface 1. Specification Version 2.0 full speed. 2. Connector description Pin Signal Description 1 VCC +3.3Vdc 2 D- Data – (Differential pinout) 3 D+ Data +(Differential pinout) 4 SG Signal Ground 3. I/O signal USB is a serial bus. It uses 4 shielded wires: two for power (+3.3V & GND) and two for differential data signals (labelled as D+ and D- in pino…
-
17, 1. OUTLINE EO10-13009A 1.6 ELECTRONIC SPECIFICATIONS 1-15 -Interrupt Transfers are used when moderate amounts of data have to transfer within a specific amount of time. -The ML60851E requests interrupts to the local MCU, etc., by asserting the -INTR pin. -Transfer of handshake packet in a direction opposite to that of the data packet. When packet transfer is completed normally, an ACK packet is returned and the operation proceeds to the next packet transfer. The ML60851E requests…
-
18, 1. OUTLINE EO10-13009A 1.6 ELECTRONIC SPECIFICATIONS 1-16 Normally condition 3 will not occur so we will look at cases 1 and 2. If 64 byte packets are continually sent back to the host, then it will continue to read the data to match the block size requested before it sends the block back to the driver. If a small amount of data is sent, or the data is sent slowly, then the latency timer will take over and send a short packet back to the host which will terminate…
-
19, 1. OUTLINE EO10-13009A 1.6 ELECTRONIC SPECIFICATIONS 1-17 1.6.4 Parallel Interface (i) Compatibility Mode (Host to Printer: Conforming to Centronics interface) (1) Data input method: 8-bit parallel (2) Synchronization method: nStrobe signal externally supplied (3) Hand shake: nAck signal and Busy signal (4) Signal level: All signals are TTL compatible. (ii) Reverse Mode: (Printer to Host) Status data is transmitted fro…
-
20, 1. OUTLINE EO10-13009A 1.6 ELECTRONIC SPECIFICATIONS 1-18 (iii) Connector Description Pin Source Compatibility mode Nibble Mode 1 Host Nstrobe HostCLK 2 Host/Ptr Data0(LSB) Data0(LSB) 3 Host/Ptr Data1 Data1 4 Host/Ptr Data2 Data2 5 Host/Ptr Data3 Data3 6 Host/Ptr Data4 Data4 7 Host/Ptr Data5 Data5 8 Host/Ptr Data6 Data6 9 Host/Ptr Data7 Data7 10 Printer Nack PtrClk 11 Printer Busy PtrBusy/Data3.7 12 Printer Perror AckDataReq/Data2.6 13 Printer Select…
-
21, 1. OUTLINE EO10-13009A 1.6 ELECTRONIC SPECIFICATIONS 1-19 (iv) Input/Output signal (1) Input signal to the printer • DATA: 8-bit parallel signal (positive logic) • STB: Strobe signal to capture 8-bit data (negative logic) • RESET: A signal to reset the printer (negative logic) • SELECT IN: A signal which goes high when the printer is transmitted to IEEE1284 mode (2) Output signal from the printer • ACK: 8-bit data r…
-
22, Toshiba TRST-A10 SERIES 1. OUTLINE EO10-13009A 1.6 ELECTRONIC SPECIFICATIONS 1-20 (3) Condition of input/output The input signal DATA1Ω8 are pulled up by 10KΩ, and other input signals are by 10KΩ, respectively. [ Printer side ] [ Host side] The output signal DATA1Ω8 are pulled up by 10KΩ, and other output signals are by 2.2KΩ,respectively. [ Printer side ] [ Host side] (vi) Receive control When the BUSY signal is low level, the data output from the host can b…
-
23, 1. OUTLINE EO10-13009A (Revision Date: Jan. 18, 2008) 1.7 DRAWER INTERFACE 1-21 1.7 DRAWER INTERFACE 1.7.1 Drawer Kick Drive Signal This signal outputs a pulse specified by ESCp. The SW (+) status can be checked by the connector pin #34 for the parallel interface, and by DLE, EOT, GSa, GSr commands for the serial/parallel interface. 1.7.2 Electric Characteristics 1) Drive voltage: DC24V 2) Drive current: Max. 1.5A (within 510ms) 3) SW signal: Signal level “L” = 0 ∼ 0.5V “H” = 3 ∼ 5V …
-
24, Toshiba TRST-A10 SERIES 1. OUTLINE EO10-13009A (Revision Date: Jan. 18, 2008) 1.7 DRAWER INTERFACE 1-22 1.7.4 Drive Circuit
…
-
25, Toshiba TRST-A10 SERIES 1. OUTLINE EO10-13009A 1.8 DC POWER CONNECTOR 1-23 1.8 DC POWER CONNECTOR The DC power connector of the AC adapter is shown below. Connector Description No. Function 1 +24V 2 GND 3 N.C SHELL F.G Applicable connector: TCS7960-53-2010 (HOSHIDEN) or equivalent. Adaptable connector: TCP8927-63-1100 (HOSHIDEN) or equivalent. TCP8927-53-1100 (HOSHIDEN) or equivalent. GA1009-38TINI (WIESON) or equivalent. 1.9 POSITION OF CUTTER 17.5mm …
-
26, 1. OUTLINE EO10-13009A 1.10 SENSORS 1-24 1.10 SENSORS 1) Cover open sensor This sensor performs synchronizing with the printer cover’s open/close at the paper roll replacement, and adopts a mechanical switch. The thermal head is also opened/closed together with the printer cover. When the printer cover is opened, the printer stops all performance. 2) Paper End Sensor (P.E. Sensor) This sensor detects presence or absence of the paper just before the thermal …
-
27, Toshiba TRST-A10 SERIES 2. SUPPLY SPECIFICATIONS EO10-13009A 2.1 EFFECTIVE PRINTING AREA 2-1 2. SUPPLY SPECIFICATIONS 2.1 EFFECTIVE PRINTING AREA 80mm paper Front Page Rear Page C D Printable Area A =4mm+/- 1mm Printable Area B=4mm+/- 1mm C=16.8 mm +/-1mm D=52.5mm +/-1mm E=72mm F= Depend on Print data condition ( recommendation 2mm ) F F A E B A E B The above shows the printing area for the first transaction. Printable area for the second transaction onwards is as follows. Front Page Rear Page 17.5 mm Logo / …
-
28, 2. SUPPLY SPECIFICATIONS EO10-13009A 2.1 EFFECTIVE PRINTING AREA 2-2 58mm paper Front Page Rear Page C D Printable Area A =4mm+/- 1mm Printable Area B=4mm+/- 1mm C=16.8 mm +/-1mm D=52.5mm +/-1mm E=72mm F= Depend on Print data condition ( recommendation 2mm ) F F A E B A E B Front Page Rear Page 17.5 mm Logo / Information print Logo / Information print 52 Printable Area Printable Area A = 2 mm +/-1 mm B = 2 mm +/-1 mm C = 17.5mm +/-1 mm E = 54mm F = Depend on print data condition (recommendation 2mm) The abov…
-
29, Toshiba TRST-A10 SERIES 2. SUPPLY SPECIFICATIONS EO10-13009A 2.2 DESIGN OF PAPER ROLL 2-3 2.2 DESIGN OF PAPER ROLL Use only paper which meets the following specification. Paper type Thermal paper rolled with the print side facing outside Width (W1) 80 +/ -1.0 mm Width (W2) 58 +0/ -1.0 mm (With optional 58 mm paper guide) Outer diameter (D) 76 +/-2.0 mm Paper thickness (T) 0.065 +/- 0.005 mm Weight 53 g/m 2 Outer core diamet…
