Data: UPD 1st November 2023
Art HeadTAP Music Equipment PDF Specifications (Updated: Wednesday 1st of November 2023 10:48:43 PM)
Rating: 4.7 (rated by 8 users)
Compatible devices: ARTcessories DUAL RP, DUALXDIRECT, AUDIOMATIC, Nor275, MX624, CleanBOX II, PDB, X100.
Recommended Documentation:
Text Version of Art HeadTAP Music Equipment Manual (Summary of Contents)
(Ocr-Read of Document's Main Page, UPD: 01 November 2023)
Sometimes floor monitors are a problem. There isn’t enough room
for them onstage or someone sits in and can’t hear the monitors
or the drummer can’t hear them well enough. Or perhaps it’s a
pick-up gig or a rehearsal and you didn’t have enough time to set
them up. In any case,sometimes it would be preferable just to
put on headphones and somehow connect them to the PA. That’s
where the HeadTAP comes in.
The HeadTAP is a passive device with an input to connect the
PA or monitor amplifier and an output to connect the headphones.
A volume control regulates the headphone level and internal
resistors keep the unit’s impedance high enough to protect the
headphones. It also protects the amplifier from encountering
too low a load impedance while powering tap units,the speaker
system or several tap units by themselves. A good tap will also
work with a stereo headphone amplifier for use in recording
situations when you want to add headphones for additional
performers.
Specifications:
• The HeadTAP provides quick and convenient tapping facilities to
permit powering headphones directly from an amplifier.
• Dual parallel 1/4”stereo/mono input jacks permit daisy-chaining
taps and/or speakers.
• Stereo/mono input selector button.
• Dual 1/4” stereo/mono headphone jacks.
• Level control
• Power:Passive device (requires no batteries or power adapter.)
• Dimensions: 3.75 x 2.875 x 1.5 inches (95mm x 74mm x 40mm)
• Weight :0.7lb (317g)
Usage:
a.) If the power source is mono (i.e. one channel of a PA power
amp or mixer/amp), connect a speaker cable either from the
amp or a spare jack on a speaker to the input jack on the
HeadTAP. Now set the pushbutton to Mono (down).
b.) If the power source is a stereo headphone amplifier or the
headphone output on a mixer, plug a stereo or balanced 1/4”
to 1/4” patch cord directly into the headphone output. Connect
the other end of the cable to the HeadTAP’s Input jack and set
the pushbutton for Stereo (out).
c.) Connect headphones to either of the Headphone Output jacks
on the HeadTAP or both of them if you are connecting two
headphone sets.
d.) Adjust the Volume control as desired. Remember to also turn
up the volume of the amp,mixer,headphone amp,etc., so that
there will be sufficient power to drive the HeadTAP(s).
e.) To add another HeadTAP to the circuit, simply run a stereo or
mono (depending on the usage) 1/4” to 1/4” patch cable from
the Parallel Output jack on the HeadTAP to the Input jack on
the next HeadTAP. Multiple HeadTAP's and headphones can
be interconnected this way.
March 2003
HeadTAP
Headphone Tap
Creative audio solutions in cool little boxes.
ARTcessories
™
DESIGNED & DISTRIBUTED BY:APPLIED RESEARCH AND TECHNOLOGY • 215 Tremont Street• Rochester, New York 14608 • USA
For Customer Service,please call: 585.436.2720 • Email:[email protected] • www.artproaudio.com • ART-ARTcs-03/03
90 DAY
WARRANTY
Recommended:
CZ109, DC Receiver, M-1900, Flaunt DB13000
RARE EARTH -, R-1 Remote, V-ACCORDION FR-7, Record Cleaning Machine, MusicTurner FM-1R, RSA 27
-
9720 VCO 1010321Model 9720Assembly and Using ManualDual VCO w/Modulator(c) 2000 PAiA Electronics, Inc.The 9720 Dual VCO w/Modulator features two independent VCOs,each with a chromatic range of 10 octaves from 16Hz to 16kHz at a+/- 1cent pitch error. Total range of each oscillator ...
Model & Doc Type: 9720 28
-
FRONT PANEL CONNECTIONS & CONTROLSGETTING STARTEDIMPRINTKOMA Elektronik GmbH is a subsidiary company of KOMA Elektronik B.V.Vertretungsberechtigte Geschäftsführer / Managing Director: Christian Zollner & Wouter JaspersSitz der Gesellschaft / Registered Office: Berlin, Germany ...
Model & Doc Type: BD 101 2
-
Your OPT-4 Speaker Selector-Volume Control is designed to operate with up to 4 pairs ofloudspeakers of 4, 8, and 16 Ohms impedance in any combination. It can be used with one or two stereoamplifiers, or with 4 Channels of a surround-sound type sound system. Each of the 4 output controlcha ...
Model & Doc Type: OPT-4 2
-
Quintet Tone Curve PedalInstructionsRevised 01/01/08®The THD Quintet™ Tone Curve Pedal is a new type of tone control pedal designed to give 5 new sounds from each of your existing pickups combinations. As it inter-acts differently with different pickups, it will give a different ...
Model & Doc Type: Quintet 1
Operating Impressions, Questions and Answers:
