Specifications:46/46006-u857au.pdf file (11 Mar 2024)
|
Audio Technica unipoint U857AU Microphone PDF Specifications (Updated: Monday 11th of March 2024 08:17:45 PM)
Rating: 4.7 (rated by 21 users)
Compatible devices: ATM450, PRO 31, 3000 Series, PROPOINT PRO 40Q, PRO 49Q, ES961RC, UniLine U853RU, AT3035.
Recommended Documentation:
• Designed for high-quality sound reinforcement, professional recording and broadcasting • UniLine ™ polar pattern provides narrow 90° acceptance angle • Superior off-axis rejection for maximum gain before feedback • UniGuard ™ RFI-shielding technology offers outstanding rejection of radio frequency interference (RFI) • Easy-to-adjust, rugged, small-diameter, alternating gooseneck with virtually no “memory” permits quick positioning into desired shape • UniSteep ® filter provides a steep low-frequency attenuation to improve sound pickup without affecting voice quality • Accepts interchangeable elements to permit angle of acceptance from 90º to 360º • Two-stage foam windscreen yields dramatically improved resistance to P-pops and other breath blasts • Direct mounts to any 5 / 8 "-27 stand, or to included threaded mounting flange • Operates on battery or phantom power The U857AU requires 11-52V DC phantom power or a 1.5V AA battery for operation. A battery need not be in place for phantom po wer operation. Battery installation: Remove the cap from the top of the power module. Insert a fresh 1.5V AA battery (“+” end toward the cap release button), then reassemble the power module. Alkaline batteries are recommended for longest life. Remove the battery during long-term storage. Output from the power module’s XLRM-type connector is low impedance (Lo-Z) balanced. The signal appears across Pins 2 and 3; Pin 1 is ground (shield). Output phase is “Pin 2 hot” – positive acoustic pressure produces positive voltage at Pin 2. An integral 80 Hz high-pass UniSteep ® filter provides easy switching from a flat frequency response to a low-end roll-off. The roll-off position reduces the microphone’s sensitivity to popping in close vocal use. It also reduces the pickup of low-frequency ambient noise (such as traffic, air-handling systems, etc.), room reverberation and mechanically coupled vibrations. The U857AU features a 9.8' (3.0 m) permanently attached miniature cab le. It connects to the provided AT8531 power module via a special TA3F-type connector designed to optimize RFI immunity. Cable exit is from the bottom of the microphone. The included pass-through adapter, designed for use with desk stands and microphone stands, provides a side-exit for the cable. Avoid leaving the microphone in the open sun or in areas where temperatures exceed 110° F (43° C) for extended periods. Extremely high humidity should also be avoided. NOTE: Audio-Technica has developed a special RFI-shielding mechanism, which is an integral part of the connectors in the UniPoint line. If you remove or replace the connector, you may adversely affect the unit's RFI immunity. Fréquence - Hertz LÉGENDE 12" ou plus sur l'axe Pente de diminution Réponse en Fréquence Réponse - dB 8 kHz 200 Hz 1 kHz 5 kHz Directivité ÉCHELLE: 5 dB PAR DIVISION LÉGENDE Audio-Technica U.S., Inc., 1221 Commerce Drive, Stow, Ohio 44224 Audio-Technica Limited, Old Lane, Leeds LS11 8AG Angleterre www.audio-technica.com P51688 ©2005 Audio-Technica U.S., Inc. Imprimé aux E.U. 8 kHz Polar Pattern SCALE IS 5 DECIBELS PER DIVISION LEGEND 200 Hz 1 kHz 5 kHz F requency in Hertz LEGEND 12" or more on axis Roll-off Frequency Response Response in dB Audio-Technica U.S., Inc., 1221 Commerce Drive, Stow, Ohio 44224 Audio-Technica Limited, Old Lane, Leeds LS11 8AG England www.audio-technica.com P51688 ©2005 Audio-Technica U.S., Inc. Printed in U.S.A. U857AU UNILINE ™ CONDENSER GOOSENECK MICROPHONE U857A U SPECIFICATIONS† ELEMENT Fixed-charge back plate per manently polarized condenser POLAR P ATTERN Line Cardioid FREQ UENCY RESPONSE 30-20,000 Hz LO W FREQUENCY ROLL-OFF 80 Hz, 18 dB/octa ve OPEN CIRCUIT SENSITIVITY –38 dB (12.5 mV) / (Phantom / Batter y) –39 dB (11.2 mV) re 1V at 1 Pa* IMPED ANCE (Phantom / Batter y) 200 ohms / 270 ohms MAXIMUM INPUT SOUND LEVEL 130 dB / 120 dB SPL, (Phantom / Batter y) 1 kHz at 1% T.H.D. DYNAMIC RANGE (typical) 110 dB / 100 dB, (Phantom / Batter y) 1 kHz at Max SPL SIGNAL-T O-NOISE RATIO 1 74 dB , 1 kHz at 1 Pa* PHANT OM POWER REQUIREMENTS 11-52V DC , 2 mA typical B ATTERY TYPE 1.5V AA/UM3 BATTERY CURRENT/LIFE 0.4 mA / 1200 hours typical (alkaline) SWITCH Off , on-flat, on-roll-off WEIGHT MICR OPHONE 5.0 oz (141 g) PO WER MODULE 4.9 oz (139 g) DIMENSIONS MICR OPHONE 16.81" (427.0 mm) long, 0.48" (12.2 mm) head diameter PO WER MODULE 3.31" (84.0 mm) H x 2.48" (63.0 mm) W x 0.87" (22.0 mm) D OUTPUT CONNECTOR Integral 3-pin XLRM-type (power module) CABLE 9.8' (3.0 m) long (per manently attached to microphone), 0.13" (3.2 mm) diameter , 2-conductor shielded cab le with TA3F-type connector OPTIONAL INTERCHANGEABLE UE-C cardioid (120°); ELEMENTS UE-H h ypercardioid (100°); UE-O omnidirectional (360 °) A CCESSORIES FURNISHED A T8531 power module; AT8154 tw o-stage foam windscreen; A T8663 A-mount flange; AT8664 A-mount cable pass-through adapter; battery † In the interest of standards development, A.T.U.S. offers full details on its test methods to other industry professionals on request. *1 P ascal = 10 dynes /cm 2 = 10 microbars = 94 dB SPL 1 Typical, A-weighted, using Audio Precision System One. Specifications are subject to change without notice. • Conçu pour le renforcement sonore, l’enregistrement professionnel et la radiodiffusion de haute qualité • Directivité UniLine ™ fournissant un angle d’acceptance étroit de 90° • Rejet hors axe supérieur pour un gain avant accrochage maximal • Excellent rejet des interférences rf • Col de cygne de faible diamètre, robuste et facile à régler pour un positionnement rapide dans la forme voulue • Filtre UniSteep ® pour une forte atténuation des basses fréquences ; améliore la prise de son sans affecter la qualité de la voix • Peut recevoir des capsules interchangeables, ce qui permet d’avoir un angle d’acceptance allant de 90° à 360° • Bonnette anti-vent en mousse double épaisseur, offrant une très haute résistance aux plosives et bruits de souffle en général • Fixation directe à tous les pieds filetés 5 / 8 "-27 ou à la bride filetée de fixation fournie • Fonctionne sur pile ou alimentation fantôme Pour faire fonctionner l’U857AU, il faut soit une alimentation fantôme de 11 à 52V CC, soit une pile de 1,5V AA. Quand on utilise une alimentation fantôme, il n’est pas nécessaire de mettre une pile. Installation de la pile : enlever le couvercle qui est sur le dessus du module d’alimentation, insérez une pile neuve de 1,5 Volts, de type AA (le + du coté du bouton d’ouverture du couvercle), puis refermer le module d’alimentation. Il est conseillé d’utiliser des piles alcalines car elles durent plus longtemps. Retirez la pile en cas de non-utilisation prolongée. La sortie du module d’alimentation est symétrique basse impédance, elle se fait sur une embase XLRM 3 broches. Le signal symétrique est entre les broches 2 et 3, le point chaud est en deux (la tension positive sur le point chaud est générée par une pression acoustique positive sur la capsule). La masse (blindage) est sur la broche 1. Un filtre passe-haut 80 Hz intégré UniSteep ® permet de passer facilement de la réponse en fréquences plate à l’atténuation des graves. La position passe-haut sert à rendre le microphone moins sensible aux “pops” quand il est utilisé en proximité sur voix. Elle sert également à réduire la sensibilité aux bruits ambiants de basse fréquence (dus au trafic, aux installations de ventilation, etc.), à la réverbération de la pièce et aux vibrations couplées mécaniquement. Le U857AU présente un câble miniature de 3,0 m (9,8 pi) fixé en permanence. Il se connecte au module d'alimentation AT8531 fourni par l'intermédiaire d'un connecteur spécial de type TA3F conçu pour optimiser l'immunité vis-à-vis du brouillage radioélectrique. La sortie de câble s'effectue à la base du microphone. L'adaptateur pass-through inclus, conçu pour une utilisation avec des pieds pour table et des pieds pour microphone, permet une sortie latérale du câble. Evitez de laisser le microphone en plein soleil ou dans des endroits où la température est supérieure à 43°C (110°F) pendant une durée prolongée. Une trop forte humidité doit également être évitée. REMARQUE : Audio-Technica a développé un dispositif spécial d'écran RFI faisant intégralement partie des connecteurs dans la ligne UniPoint. Si vous retirez ou replacez le connecteur, vous pouvez affecter l'immunité vis-à-vis du brouillage radioélectrique. U857AU MICROPHONE COL DE CYGNE À CONDENSATEUR UNILINE ™ U857AU CARACTÉRISTIQUES TECHNIQUES † TYPE Condensateur polarisé en permanence avec plaque fixe à charge fixe DIRECTIVITÉ Cardioïde-ligne RÉPONSE EN FRÉQUENCE 30-20 000 Hz ATTÉNUATION DES GRAVES 80 Hz, 18 dB/octave NIVEAU DE SORTIE –38 dB (12,5 mV) / (Fantôme / Pile) –39 dB (11,2 mV) réf 1V/Pa* IMPÉDANCE (Fantôme / Pile) 200 ohms / 270 ohms NIVEAU DE PRESSION 130 dB / 120 dB SPL, ACOUSTIQUE MAXIMAL 1 kHz à 1% T.H.D. (Fantôme / Pile) DYNAMIQUE (typique) 110 dB / 100 dB, (Fantôme / Pile) 1 kHz à SPL max. RAPPORT SIGNAL/BRUIT 1 74 dB, 1 kHz/Pa* ALIMENTATION FANTÔME 11-52V CC, 2 mA typiques TYPE DE PILE 1,5V AA/UM3 COURANT / DURÉE DE VIE 0,4 mA / 1200 heures typiques DE LA PILE (alcaline) COMMUTATEUR Off, on-plat, on-atténuation POIDS MICROPHONE 141 g (5,0 oz) MODULE D'ALIMENTATION 139 g (4,9 oz) DIMENSIONS MICROPHONE Longueur 427,0 mm (16,81 po), diamètre de la tête 12,2 mm (0,48 po) MODULE D'ALIMENTATION Hauteur 84,0 mm (3,31 po) x largeur 63,0 mm (2,48 po) x profondeur 22,0 mm (0,87 po) CONNECTEUR DE SORTIE Type XLRM 3 broches intégré (module d'alimentation) CÂBLE Câble blindé à 2 conducteurs, de 3,2 mm de diamètre (0,13 po) et 3,0 m de long (9,8 pi) (solidaire du microphone), avec connecteur de sortie TA3F CAPSULES INTERCHANGEABLES UE-C cardioïde (120°); EN OPTION UE-H hypercardioïde (100°); UE-O omnidirectionnel (360°) ACCESSOIRES FOURNIS AT8531 module d'alimentation ; AT8154 bonnette anti-vent en mousse double épaisseur ; AT8663 bride montée en A ; AT8664 adaptateur pass-through câble monté en A ; pile † Afin de contribuer au développement des normes, A.T.U.S. fournit tout renseignement sur ses méthodes de test aux professionnels de l’industrie qui en font la demande. *1 Pascal = 10 dynes/cm 2 = 10 microbars = 94 dB SPL 1 Typique, pondéré en A, mesuré avec l’Audio Precision System One. Les caractéristiques techniques sont soumises à des changements sans préavis.
FLS625 Speakers - #735536
FLS625, 6, intex/fls625.pdf
Lawn Mower maverick 4800 Instruction, #M718PD
maverick 4800, 64, bad-boy/maverick-4800.pdf
#V4DT78: 8943 Guidance
8943, 13, dukane/8943.pdf
Scale Health o meter BFM955 Guidance, #QE69BY
Health o meter BFM955, 2, sunbeam/health-o-meter-bfm955.pdf
Enviro User Guide Pellet stove EF2 (#C3ZJER)
EF2, 9, enviro/ef2.pdf
Ibanez Guide Musical Instrument Amplifier TA25 (#UE22QD)
TA25, 5, ibanez/ta25.pdf
Tutorial (WLL3120, #QS6653)
WLL3120, 76, askey/wll3120.pdf
#7JY22O: APC-3228A Document
APC-3228A, 96, aplex/apc-3228a.pdf
Smartcode 910 Locks - #3ID47F
Smartcode 910, 4, kwikset/smartcode-910.pdf
Yamaha User Manual: CLP-100 (#M553WU)
CLP-100, 108, yamaha/clp-100.pdf
TECHNICAL SUPPORTTel: 0191 224 3174Fax: 0191 224 4938Email: [email protected]: www.videxuk.comSERIES3000DOOR OPENPRIVACY ONDOOR OPENPRIVACY ON3125 3000 Series Audiophone QUICK GUIDEQG_3125_V.1.0_03/17Door Open buttonHandset speakerHandset microphoneAudiophoneHandsetHandset cordFront cover retain ...
Model & Doc Type: 3000 Series 2
TG I56c deutsch TG I56c english TG I56c françaisSie haben sich für das Kondensatormikrofon TG I56c von beyerdynamic entschieden. Vielen Dank für Ihr Ver trauen.Nehmen Sie sich bitte einige Minuten Zeit und lesen Sie dieseProdukt information vor Inbetriebnahme aufmerksam dur ...
Model & Doc Type: TG I56c 2
Introductionank you and congratulations on your purchase of the Miktek PM9 , Performance Series handheld stage microphone. You work hard to give a better than average performance, so you demand a better than average microphone to reproduce the sound of your voice. Miktek Performance Series hand ...
Model & Doc Type: PM9 2
Technical Support Should you have any questions regarding your SR25 microphone please contact us: e-mail: [email protected] phone: 1-603-654-6427 (9a.m. – 5p.m. ET) For warranty and product return/exchange information please refer to the back of the enclosed Calibration Chart. ...
Model & Doc Type: SR25 2
# | Brand | Model | Document Type/File | Pages | File Size | Last Checked |
---|---|---|---|---|---|---|
1 | ICON ProAudio | Definitor air Series |
18 | 06/10 | ||
2 | iRig | Mic Cast 2 |
10 | 09/02 | ||
3 | Shure | VR300 |
2 | 0.08 Mb | 13/10 | |
4 | Shure | 206 |
2 | 0.43 Mb | 21/02 | |
5 | Sennheiser | SKP 500 G2 |
29 | 0.42 Mb | 22/09 | |
6 | Sony | ECM-T140 |
8 | 24/11 | ||
7 | Sennheiser | ew 100 G4 |
2 | 17/09 | ||
8 | Nuvo | aea n22 |
14 | 06/11 | ||
9 | Sennheiser | ME 34 |
36 | 1.41 Mb | 04/01 | |
10 | Shure | 545D |
3 | 0.07 Mb | 05/01 |
# | Brand | Model | Document (PDF) | Pages | Size | Check Date |
---|---|---|---|---|---|---|
1 | MK Diamond Products | MK-370 EXP |
6 | 10.11.2023 | ||
2 | Samsung | HT-H5500W |
48 | 10.22 Mb | 27.10.2023 | |
3 | Roberts | RT100 |
20 | 22.02.2024 | ||
4 | Sony | KV-BZ212 |
20 | 15.01.2024 | ||
5 | Jensen | A1000 |
6 | 11.11.2023 | ||
6 | Meridian | 3100 |
8 | 06.10.2023 | ||
7 | Arrive | ViewPoint 2240 |
58 | 09.02.2024 | ||
8 | Makita | JS1600 |
24 | 23.02.2024 | ||
9 | Panasonic | ES-2113 |
16 | 01.02.2024 | ||
10 | Mirage | HDMIRAGE10 |
18 | 11.03.2024 |