Data: UPD 28th December 2023
Casio TQ-309 Clock PDF Operation Manual (Updated: Thursday 28th of December 2023 03:33:08 PM)
Rating: 4.8 (rated by 95 users)
Compatible devices: 2322, PQ-60, DQD-110B, DQ-683, DIVAR AN 3000, DQ-745S, 1675, ID-17.
Recommended Documentation:
Text Version of Casio TQ-309 Clock Manual (Summary of Contents)
(Ocr-Read of Document's Main Page, UPD: 28 December 2023)
Operation Guide TQ-309
1
MA0411-EA
• A sticker is affixed to the glass of this clock when you purchase it. Be sure to remove the sticker before using the
clock.
• Depending on its model number, the appearance of your clock may differ somewhat from that shown in the
illustration.
GENERAL GUIDE
11
11
1 Light/Snooze button
• Hold down to illuminate the display.
• Pressing this button while the alarm is sounding stops the alarm.
22
22
2 Hour hand
33
33
3 Minute hand
44
44
4 Second hand
55
55
5 Alarm hand
66
66
6 Alarm ON/OFF switch
77
77
7 Time/Alarm setting knob
• Press in and rotate to set the alarm.
• Pull out and rotate to set the time.
88
88
8 Battery
99
99
9 Catch
00
00
0 Battery cover
12
1
2
3
4
5
6
7
8
9
10
11
ON
OFF
1
2
ILLUSTRATION
SETTING THE TIME
1. Load the battery, making sure its ends are facing as shown in the illustration.
2. Remove the battery to stop the Second hand (4) at 12 o’clock position.
3. Pull out the Time/Alarm setting knob (7) and rotate it to set the time.
• Note that this clock does not distinguish between AM and PM times.
4. After setting the time, push the Time/Alarm setting knob (7) back to its original position.
5. Replace the battery at a time signal to restart the Second hand (4) on the correct second.
• The start of Second hand (4) may be delayed depending on when you load the battery.
USING THE ALARM
When the alarm is turned on, the alarm sounds for 60 minutes at the preset time each day. Once the alarm starts to
sound, you can switch it off by pressing the Alarm ON/OFF switch (6).
Setting the Alarm Time
1. Making sure the Time/Alarm setting knob (7) is not pulled out, rotate the knob to move the Alarm hand (5)
counterclockwise to the setting you want.
2. Raise the Alarm ON/OFF switch (6) to turn on the alarm.
• Note that this clock does not distinguish between AM and PM times. If you set an alarm to wake up to in the
morning, the alarm will sound again at the same time in the evening if you leave the Alarm ON/OFF switch (6)
raised.
Stopping the Alarm
While the alarm is sounding, press the Light/Snooze button (1) to stop it.
• The snooze alarm remains activated for about 60 minutes. During that time, the alarm will sound again about four
or five minutes after you press the Light/Snooze button (1) to stop the current alarm.
• Pressing the Light/Snooze button (1) also turns on display illumination.
The alarm will not sound if the Alarm ON/OFF switch (6) is in the OFF position.
LUMINOUS FACE
Special plastic is used for numerals and face markings to make them appear to glow.
BATTERY REPLACEMENT
Low battery power is indicated when timekeeping slows or stops completely. Should either of these symptoms
occur, replace the battery as soon as possible. Do not leave a low or dead battery in the clock.
1. Open the Battery cover (0) as shown in the illustration.
2. Remove the old battery.
3. Load a new battery. Make sure that its positive (+) and negative (–) ends are facing correctly.
4. Replace the Battery cover (0).
Battery precautions
• Keep batteries out of the reach of small children. If a battery is accidentally swallowed, contact your physician
immediately.
• Be sure to load the battery with its positive (+) and negative (–) ends facing correctly.
• Never charge the battery that comes with the clock.
• Should a battery ever leak while in the clock, wipe out the fluid with a cloth, taking care not to let any get onto
your skin.
• Replace the battery at least once a year, even if the current battery is working normally.
• The battery that comes with the clock loses some power during transport and storage.
Recommended:
SM5-MV5003G3, ST-III Series, JBC Series, FTB-500
Global Series, 3216, CT-714, Glass photo clock, 513-1918S
-
1GBINTRODUCTIONCongratulations on your purchasing the RM318P RF Pro-jection Clock. The RM318P is a feature-packed devicewhich automatically synchronizes its current time and datewhen it is brought within an approximate 1500km radius ofthe radio signal generated from Frankfurt, Germany ...
Model & Doc Type: rm318p 8
-
Instruction ManualSAVE THIS MANUAL FOR FUTURE REFERENCE.Questions? Contact Customer Support at (877) 221-1252 or visit www.AcuRite.com.CONTENTSUnpacking Instructions ........... 2Package Contents .................. 2Product Registration ............... 2Features & Benets ............. ...
Model & Doc Type: 75127 8
-
21 Pre-Installation 1. Verify network infrastructure with Network Administrator. • Power over Ethernet (PoE) solution • Dynamic Host Conguration Protocol (DHCP) settings 2. Plan Digital PoE Clock locations and cabling routes Unpack the box • Remove the components f ...
Model & Doc Type: Global Series 2
-
1. How to set Vibration Speed, Beep Volume and Number of Beeps. Vibration Speed (1 = low, 2 = medium, 3 = high), Beep Volume (1-3), Number of beeps (1-6). (Factory settings are Vibration = 3; Beep volume = 3; Beep number = 3) 2. How to set the Time and Date (The Invisibl ...
Model & Doc Type: Invisible ClockoII 4
Operating Impressions, Questions and Answers:
