-
7, Cisco IAD2430 vii Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide OL-4234-06 Preface This preface describes the audience, organization, and conventions of this publication, and describes how to obtain additional documentation. Audience This publication is designed for people who have some experience installing networking equipment such as routers, servers, and switches. The person installing Cisco IAD2430 series integrated access devices (IADs) should be familiar with networks and telephony equipment as well as with electronic c…
-
3, Cisco IAD2430 iii Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide OL-4234-06 CONTENTS Preface vii Audience vii Organization vii Conventions viii Safety Warnings viii Warning Definition ix Product Serial Number Location xiv Accessibility xv Related Documentation xvi Obtaining Documentation and Submitting a Service Request xvi CHAPTER 1 Overview of Cisco IAD2430 Series IAD…
-
82, 4-10 Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide OL-4234-06 Chapter 4 Powering On Cisco IAD2430 Series IADs Troubleshooting Ta b l e 4-1 Troubleshooting the Cisco IAD Symptom Possible Cause Corrective Action Power LED and fan are off Power source turned off Turn on power source. Faulty power cable Check/replace power cable. Faulty power source Check/correct input power. Faulty internal power supply Contact Cisco…
-
11, xi Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide OL-4234-06 Preface Safety Warnings
…
-
79, 4-7 Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide OL-4234-06 Chapter 4 Powering On Cisco IAD2430 Series IADs Initial Configuration Procedures Configuring a T1/E1 Port for a WAN Connection The T1/E1 port supports balanced T1/E1 according to ANSI T1.403 and has a built-in CSU/DSU. To configure basic T1/E1 controller settings to support Point-to-Poing Protocol (PPP), High-Level Data Link Control (HDLC), or Frame Relay (FR), follow these steps, beginning in global configurat…
-
60, 3-24 Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide OL-4234-06 Chapter 3 Installing Cisco IAD2430 Series IADs Connecting Cables WAN and Voice Cables Warning For connections outside the building where the equipment is installed, the following ports must be connected through an approved network termination unit with integral circuit protection. FXS/T3/E3 Statement 1044 Note The following warning also applies to Cisco IAD2430 units that have…
-
81, Cisco IAD2430 4-9 Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide OL-4234-06 Chapter 4 Powering On Cisco IAD2430 Series IADs Troubleshooting Troubleshooting This section describes possible mechanical problems and corrective actions. If there appears to be a malfunction, first check all cables and connections. If these are in order, see Table 4-1 for specific problems and solutions. For problems with the configuration, see the Cisco IAD2430 Series Software Configuration Guide at the following URL: …
-
41, 3-5 Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide OL-4234-06 Chapter 3 Installing Cisco IAD2430 Series IADs Unpacking and Inspection – Eight wood screws or other fasteners for installing the chassis on a wall. An additional starter screw can be used to facilitate wall-mounting (does not include Cisco IAD2435 IAD). – For Cisco IAD2435 IAD—two number-six, 3/4-inch (M3.5 x 20-mm) screws. • ESD-preventive wrist strap In addition, you might need the following external equipment: • Console terminal, or…
-
39, 3-3 Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide OL-4234-06 Chapter 3 Installing Cisco IAD2430 Series IADs Site Log • Look carefully for possible hazards in your work area, such as moist floors, ungrounded power extension cables, and missing safety grounds. • If an electrical accident occurs, proceed as follows: – Use caution; do not become a victim yourself. – Turn off power to the system. – If possible, send another person…
-
25, 1-9 Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide OL-4234-06 Chapter 1 Overview of Cisco IAD2430 Series IADs Chassis Grounding Chassis Grounding Chassis grounding is provided through the power cable, which uses a standard grounding plug. The chassis is also equipped with two 4 x 0.7 screw terminals for chassis grounding. The accessory kit contains a crimp-type ground lug that attaches to the two screw terminals. For m…
-
46, Cisco IAD2430 3-10 Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide OL-4234-06 Chapter 3 Installing Cisco IAD2430 Series IADs Wall-Mounting the Chassis Caution Be sure to use the correct screws and plastic washers for this mounting option. (See Table 3-1 on page 3-7.) Figure 3-9 Attaching the Brackets for Wall-Mounting Step 2 Attach the second bracket to the opposite side of the chassis. Step 3 Attach the router to the wall using the brackets previously attached and u…
-
42, 3-6 Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide OL-4234-06 Chapter 3 Installing Cisco IAD2430 Series IADs Rack-Mounting the Chassis Inspect all items for shipping damage. If anything appears damaged, or if you encounter problems when installing or configuring your system, contact a customer service representative. (See the “Obtaining Documentation and Submitting a Service Request” section on page xvi.) Rack-Mounting the Chassis Your chassis ship with a pair of…
-
56, 3-20 Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide OL-4234-06 Chapter 3 Installing Cisco IAD2430 Series IADs Connecting Cables Figure 3-17 LAN and Administrative Access Connections Figure 3-18 LAN, Administrative Access, and Connections (Cisco IAD2435 IAD) 1 Fast Ethernet port 2 Console port 3 AUX port 4 Fast Ethernet (straight-through) 5 RJ-45-to-DB-9 console cable 6 RJ-45-to-DB-25 auxiliary cable…
-
30, 1-14 Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide OL-4234-06 Chapter 1 Overview of Cisco IAD2430 Series IADs Deployment Options Figure 1-14 T1/E1 WAN Interface with Analog FXS User Interfaces Figure 1-15 WAN Interface with Analog FXS and FXO User Interfaces Figure 1-16 T1/E1 with T1/E1 Interface to PBX IAD WAN T1 RJ-21 Ethernet Analog telephones Distribution panel 88998 Cisco IAD model number: IAD2431-8FXS IAD2431-16FXS IAD2432-24FXS I…
-
71, 3-35 Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide OL-4234-06 Chapter 3 Installing Cisco IAD2430 Series IADs Connecting Backup Power Note UPS functionality is not available on the Cisco IAD2435 IAD. Figure 3-32 shows a setup using a UPS. Note Figure 3-32 shows one possible setup; please review your UPS documentation before you set up your system. Figure 3-32 Connecting a UPS to an AC-Powered Cisco IAD 95251 IAD2431-8FXS Cisco IAD 2430 series…
-
2, THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS. THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET TH…
-
20, 1-4 Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide OL-4234-06 Chapter 1 Overview of Cisco IAD2430 Series IADs Overview Figure 1-4 Cisco IAD2431-8FXS Chassis Cisco IAD2431-16FXS The Cisco IAD2431-16FXS IAD (Figure 1-5) provides sixteen analog FXS ports with two 10/100BASE-T ports and two T1/E1 WAN ports. The chassis has the following interfaces: • RJ-21 analog voice interface • One T1/E1 port • Two 10/100BAS…
-
67, 3-31 Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide OL-4234-06 Chapter 3 Installing Cisco IAD2430 Series IADs Ports, Connectors, and Pinouts Figure 3-29 Digital Voice Connection Step 2 Connect the RJ-48 jack to the digital telephone equipment (PBX). Ports, Connectors, and Pinouts Table 3-5 summarizes the cable connections between Cisco IADs and the network and user interfaces. Remote Terminal Connections (If Applicable) If you are configuring a Cisco IAD from a remote location, connec…
-
78, 4-6 Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide OL-4234-06 Chapter 4 Powering On Cisco IAD2430 Series IADs Initial Configuration Procedures Enter your selection [2]: 2 Building configuration... Use the enabled mode 'configure' command to modify this configuration. Press RETURN to get started! RETURN The user prompt is displayed. Router> Step 13 Verify the initial configuration. See the �…
-
9, ix Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide OL-4234-06 Preface Safety Warnings Warning Definition Warning IMPORTANT SAFETY INSTRUCTIONS This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. To see translations of the warnings that appear in this publication, refer to the translated safety warnings that accompanied th…
-
48, Cisco IAD2430 3-12 Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide OL-4234-06 Chapter 3 Installing Cisco IAD2430 Series IADs Wall-Mounting the Chassis Caution If you are mounting the router on drywall, use two hollow-wall anchors (1/8 inch with 5/16-inch drill bit, or M3 with 8-mm drill bit) to secure the screws. If the screws are not properly anchored, the strain of the network cable connections could pull the router from the wall. Figure 3-11 Screw Holes for Wall-Mounting the IAD2435 The follo…
-
83, IN-1 Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide OL-4234-06 INDEX Numerics 19-Inch Rack Installation—Front Panel Forward 3-7 19-Inch Rack Installation—Rear Panel Forward 3-7 A AC power requirements 2-3, 3-21 analog voice ports 3-29 ASCII terminal, connecting 3-32 auxiliary port 3-23 B backup battery 3-33, 3-34 brackets 3-6, 3-9, 3-10 C cable distance limitations 2-4 to ?? cable use reference table 3-31 caution messages exceeding EIA/TIA-449 distance limitations 2-…
-
17, CHAPTER 1-1 Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide OL-4234-06 1 Overview of Cisco IAD2430 Series IADs This chapter provides a brief description of Cisco IAD2430 series integrated access devices (IADs) and contains the following sections: • Overview, page 1-1 • Physical Description, page 1-6 • LEDs, page 1-7 • Chassis Grounding, page 1-9 • Memory, page 1-9 • Port Numbering Conventions, page 1-9 • Specifications, page 1-10 • Software Elements, pag…
-
6, Contents vi Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide OL-4234-06 Remote Terminal Connections (If Applicable) 31 Connecting to a Modem 32 Connecting to a Remote PC 32 Connecting to a Remote ASCII Terminal 32 Connecting Backup Power 33 Connecting a Backup Battery to a DC-Powered IAD 33 Connecting an Uninteruptible Power Supply UPS to an AC-Powered Cisco IAD2430 Series IAD 34 CHAPTER 4 Powering On Cisco IAD2430 Series IADs 1 Checklist for Power-On 1 Power-On Procedur…
-
35, Cisco IAD2430 2-5 Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide OL-4234-06 Chapter 2 Planning Your Installation Distance Limitations for Interface Cables Caution EIA/TIA-232 is often used at greater distances than specified in Table 2-2 on page 2-4. If you understand the electrical problems that can arise and can compensate for them, you might still obtain good results; however, we recommend that you keep your cable runs within the standard-defined distances. Table 2-3 shows the standard relationship between signa…
-
45, 3-9 Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide OL-4234-06 Chapter 3 Installing Cisco IAD2430 Series IADs Wall-Mounting the Chassis Caution Make sure to use the correct screws for this mounting option (see Table 3-1 on page 3-7). Screws are included for attaching the brackets to the chassis, but not for installing the chassis in a rack or on a wall. You need four additional machine screws to install the chassis in a rac…
-
18, Cisco IAD2430 1-2 Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide OL-4234-06 Chapter 1 Overview of Cisco IAD2430 Series IADs Overview Figure 1-1 Cisco IAD2430 Series IADs Front Panel Figure 1-2 Cisco IAD2435 Series IADs Front Panel The Cisco IAD2430 series IADs support the following interfaces: • 10/100BASE-T LAN connection • T1/E1 port connections • RJ-21 analog voice interface • WAN interface card/voice interface card (WIC/VIC) options • External/internal flash memory The Cisco IAD2430 series IADs…
-
23, Cisco IAD2430 1-7 Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide OL-4234-06 Chapter 1 Overview of Cisco IAD2430 Series IADs LEDs Figure 1-10 Cisco IAD2435 Series IAD Back Panel Function Options Note A Kensington security slot is located on the router back panel. To secure the router to a desktop or other surface, use the Kensington lockdown equipment. Note The FE built-in switch ports provide connections to 10/100BASE-T (10/100-Mbps) Fast Ethernet networks. LEDs T…
