Data: UPD 8th September 2023
X10 SR731 Other PDF Installation And Operating Instructions (Updated: Friday 8th of September 2023 01:26:57 PM)
Rating: 4.8 (rated by 38 users)
Compatible devices: TR16A, XX11A, VA11A, SS15A, VK73A, MS12A, PR511, LM465.
Recommended Documentation:
Text Version of X10 SR731 Other Manual (Summary of Contents)
(Ocr-Read of Document's Main Page, UPD: 08 September 2023)
X10 Wireless Technology, Inc. Limited One Year Warranty
X10.com, a division of X10 Wireless Technology, Inc. (X10) warrants X10
products to be free from defective material and workmanship for a period of one
(1) year from the original date of purchase at retail. X10 agrees to repair or replace,
at its sole discretion, a defective X10 product if returned to X10 within the warranty
period and with proof of purchase. If service is required under this warranty:
Call 1-800-442-5065, visit www.x10.com, or e-mail [email protected].
For help or more information on setup, please visit:
http://www.x10.com/support
RF Smart Repeater
Model SR731
INSTALLATION AND OPERATING INSTRUCTIONS
The RF Smart Repeater is designed to increase the range of X10 wireless
remote controls, motion sensors, and security products that operate at 310
MHz. It does this by boosting and retransmitting RF signals it receives from
those products. You should locate the RF Smart Repeater somewhere centrally
between the product you are transmitting from and the product you want to
receive the repeated commands. In some instances you might need to
experiment with the location so that the receiver doesn’t see the repeated
commands as well as the original commands, although in most instances this is
not likely to be a problem.
INSTALLING THE REPEATER
1. Find a suitable location, preferably at least 3 feet above the ground and
centrally located between the transmitter and the receiver.
2. Plug the Smart Repeater into an AC outlet. Extend the antenna.
3. Set the codewheel on the Smart Repeater to any letter between A and D. If
you are using more than one repeater, set each one to a different sequential
letter. Install each repeater at least 50 ft. apart. Experiment with placement.
Note, ABCD is the same as EFGH, or IJKL or MNOP.
TESTING THE SMART REPEATER
1. Set the housecode on an X10 Transceiver to M (its Unit Code is always 1).
2. Press the TEST button on the Smart Repeater. The Transceiver clicks on
and off for each successive press.
SR731-10/02
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT
TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL
INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
This equipment generates and uses radio frequency energy, and if not installed and used properly,
that is, in strict accordance with the manufacturers instructions, it may cause interference to radio
and television reception. It has been type tested and found to comply with the limits for remote
control devices in accordance with the specifications in Sub-Parts B and C of Part 15 of FCC Rules,
which are designed to provide reasonable protection against such interference in a residential
installation. However, there is no guarantee that interference will not occur in a particular installa-
tion. If this equipment does cause interference to radio or television reception, which can be
determined by unplugging the equipment, try to correct the interference by one or more of the
following measures.
• Reorient the antenna of the radio/TV experiencing the interference.
• Relocate the equipment with respect to the radio/TV.
• Move the equipment away from the radio/TV.
• Plug the equipment into an outlet on a different electrical circuit from the radio/TV
experiencing the interference.
• If necessary, consult your local Dealer for additional suggestions.
NOTE: Modifications to this product will void the user's authority to operate this equipment.
Recommended:
FC3-HD, 55345-MV, Electric oil filled radiator, AC1000
EXPRESS - IRON, 52PFL5604H, OC-150, DGIPOD-1563, CFD-V35 Operating Instructions (primary manual), MPIII
-
Video InVideo OutCaption/ControlSettings52431Control Port( )( )12 VDC Pwr In100 mA maxPwrLEDContemporaryResearchVCCClosed Caption DecoderCR System ToolsCCRSH09/28/04PRODUCT DRAWINGCLOSED CAPTION DECODERNONE1 1950-5053CST-VCCCST-VSCC_PD.DWGUNLESS OTHERWISE SPECIFIED:DECIMAL ...
Model & Doc Type: VCC 1
-
MPIII Battery Change Quick Start Guide 1 Clean and dry the data logger, making sure that the surfaces are clear of contaminants or debris. Then, loosen the battery cap with the logger gripper provided by holding the logger in one hand with the probe facing toward the ground, and twisti ...
Model & Doc Type: MPIII 2
-
DATASHEETENCOUNTER DIGITAL IMPLEMENTATION SYSTEM Cadence® Encounter® Digital Implementation System refines and redefines digital implementation, helping customers deliver differentiated products to their end market, achieve predictable time to market with the highest quality silico ...
Model & Doc Type: ENCOUNTER DIGITAL IMPLEMENTATION SYSTEM 5
-
TM The 300Mbps Wireless Easy-N-Upgrader upgrades your old, perfectly functioning router, to high speed wireless n. Enjoy up to 12 times the speed and 6 times the coverage of a wireless g networkEliminate wireless dead spots, seamlessly surf the Internet and help the environment b ...
Model & Doc Type: TEW-637AP - 300Mbps Wireless Easy-N-Upgrader 2
Operating Impressions, Questions and Answers:
