Manual, Operating Instructions for Fire-Lite MS-9050UD series Control Panel, Smoke Alarm (1 pages)
Data: UPD 12th April 2024
Fire-Lite MS-9050UD series Control Panel, Smoke Alarm PDF Operating Instructions (Updated: Friday 12th of April 2024 09:09:05 AM)
Rating: 4.2 (rated by 78 users)
Compatible devices: 411, XRM-24, M301, FACP, BG-12LA, CHG-120F, ACM-16ATF, MS-9200UDLS/E.
Recommended Documentation:
Text Version of Fire-Lite MS-9050UD series Control Panel, Smoke Alarm Manual (Summary of Contents)
(Ocr-Read of Document's Main Page, UPD: 12 April 2024)
WHEN AUDIBLE DEVICES ARE SOUNDING -
FOR A FIRE ALARM
1. Evacuate the protected area
2. Notify the monitoring service and/or the Fire Department immediately. Tell them briefly what happened and what
your current status is.
Phones: ____________________________ _________________________________
Fire Department Monitoring Service
3. If the Fire Department is responding, be prepared to provide directions to arriving firefighters.
FOR TROUBLE, SUPERVISORY, AND EMERGENCY ALARMS
1. Notify the monitoring service and/or applicable first responders if this panel is connected to either one, and tell them
what is happening.
2. Silence audible devices by unlocking and opening the panel and pressing the ACKNOWLEDGE/STEP button. The
applicable indicator will remain illuminated. Contact authorized service personnel immediately! (See Below).
WARNING!
DO NOT ALLOW TROUBLE CONDITIONS TO REMAIN LOGGED IN THE SYSTEM. THE PROTECTION
THAT THE SYSTEM OFFERS HAS BEEN COMPROMISED, OR ELIMINATED WHEN A TROUBLE
CONDITION EXISTS.
To return to normal after an alarm
1. Do not enter the protected area until safe to do so.
2. Clear all initiating devices. Smoke detectors will not reset
if there is still smoke in the area.
3. Reset the control panel (PRESS the RESET button)
Power failure or brownout
If AC power drops too low or fails, AC POWER indicator will
extinguish, the system TROUBLE indicator will turn on yellow, and
the panel buzzer and any other audible trouble devices will sound.
Contact authorized service personnel immediately. See below.
Manual activation (Fire Drill or otherwise)
Notification Appliance Circuits (NACs) can be activated by
pressing and holding the DRILL button for at least two
seconds.
NOTE: You may want to disconnect municipal box by sliding
DISCONNECT switch, located on 4XTMF module, to its
disconnect position (to the right). If a DACT is con-
nected, notify the monitoring service before conducting
any fire drills or tests.
MS-9050UD Series Fire Alarm Control Panel
Operating Instructions
PANEL KEY - The key to open the panel can be found at the
following location:
NORMAL - Only AC POWER is illuminated green.
All other indicators are off. LCD display will read SYSTEM
ALL NORMAL.
Document #52663 Rev. C 4/7/2010 ECN 10-321
THIS SHEET SHALL BE FRAMED ADJACENT TO
THE CONTROL PANEL
To test the indicators, LCD display and piezo
Press and release the RESET button and check all indicators/
LEDs. Every indicator/LED should be on, LCD shows all pixels
on, piezo sounder beeps.
For more information, refer to the MS-9050UD Series Manual,
Document #52413. It is kept in the following location:
Alarm Silencing
Notification Appliance Circuits may be silenced by pressing the
ALARM SILENCE button. ALARM SILENCED will turn on yellow.
Subsequent alarms will reactivate circuits. Press the RESET
button to clear the "silenced" condition.
NOTE: Notification Appliance Circuits may be programmed as
nonsilenceable. Also, Signal Silence Inhibit, if enabled,
will prevent silencing of NACs for one minute after an
alarm (see manual).
Name: _____________________________________
Company: _________________________________
Address: ___________________________________
Telephone Number: ________________________
In the event of trouble, contact the
local Fire-Lite Service Representative
Recommended:
698A, Nespresso TK911, Primergy RX100 S3, Enclosure 3.5"
ENVIROMUX-SDS-120V, SP-64,126, zm2, MS-5UD-3, GS526, FHB10W
-
PRODUCT SERIESM300, M300AP, M300i, SA200 SA900, SA900Si, SA300 and SA300LDual Ionisation sensing chamber, particularly sensitive to fast flaming fires.SUPERIOR FEATURES• Battery Operated• Operating Light (RED)Flashes approximately every 45 seconds confirming unit is powered. • Low B ...
Model & Doc Type: Dicon M300 2
-
HoneywellC7015AInfraredFlame DetectorThe C7015A Flame Detector includes a leadsulfide photocell that is sensitive to the infraredradiation emitted by the combustion offuels suchas natural gas, oil, and coal.nqwnnParticularily suitable for combination or dual-fuel radiation is compatible wi ...
Model & Doc Type: C7015A 15
-
WHEN AUDIBLE DEVICES ARE SOUNDING -FOR AN ALARM1. Evacuate the protected area2. Notify the monitoring service and/or the Fire Department immediately. Tell them briefly what happened and what your current status is.Phones: ____________________________ ______________________ ...
Model & Doc Type: MS-5UD-3 1
-
DXS-80The DXS-80 is a UL listed†, single station, carbon monoxide alarm with a built-in supervised transmitter. It is compatible with Linear’s wireless DXS Format Security Systems, Personal Emergency Reporting Systems (PERS), and other stand-alone receivers. The DXS-80 provides ...
Model & Doc Type: DXS-80 2
Operating Impressions, Questions and Answers:
