Uniden 1360BK Operation & User’s Manual

Operation & User’s Manual for Uniden 1360BK Conference Phone, Telephone (1 pages)

Specifications:

158/158978-1360.pdf file (03 Dec 2023)
  • Manufacturer: Uniden
  • Category of Device: Conference Phone, Telephone
  • Document: 1360BK, File Type: PDF Operation & User’s Manual
  • Updated: 03-12-2023
  • Count of Pages: 1
Download 1360BK Manual (1 pages)

Read PDF Document Online:

Data: UPD 3rd December 2023

Uniden 1360BK Conference Phone, Telephone PDF Operation & User’s Manual (Updated: Sunday 3rd of December 2023 01:56:48 AM)

Rating: 4.3 (rated by 22 users)

Compatible devices: DSS 5855 series, EXT1465, FP102, D3288, D1788, DECT1363, DECT 2145 Series, 3775.

Recommended Documentation:

Text Version of Uniden 1360BK Conference Phone, Telephone Manual (Summary of Contents)

(Ocr-Read of Document's Main Page, UPD: 03 December 2023)


Installing and Replacing the Batteries
Your Caller ID phone uses 4 AA-size alkaline batteries for receiving and storing Caller ID 
records and for storing the numbers you use for memory dialing, pulse dialing, and redial.
IMPORTANT: You will have approximately 90 seconds to replace 
the batteries before the memories stored are lost. Please read the 
instructions before replacing the batteries and have the batteries ready 
to be inserted beforehand.
IMPORTANT: If you are not going to use the telephone for more than 30 
days, remove the batteries because they may leak and damage the unit.
1.  Disconnect the telephone line cord and remove the desk 
stand from the back of the base.
2.  Release latch or the battery compartments and remove 
cover.
3.  Insert 4 AA-size alkaline batteries as shown on the 
diagram in the battery compartments.
4.  Snap the battery compartment door back into place and 
replace the desk stand.
5.  Connect the line cord and check your memory locations.
NOTE: If the low battery icon appears in the display, you need to replace 
the batteries. It is important that you replace the batteries as soon as 
possible in order to maintain Caller ID operation. 
Installing the Phone
Your phone should be placed on a level surface, such as a desk or table top, or you can 
mount it on a wall.  
Connecting the Handset
1.  Connect one end of the coiled handset cord to the jack on the handset. 
2.  Plug the other end of the coiled handset cord to the jack on the base.
3.  Place the handset in the cradle.
Connecting the Telephone Line
1. 
Connect one end of the straight telephone line cord to the jack on the back of the base.
2.  Connect the other end to a wall phone jack.
3. 
Set the ringer volume switch located at the back of the base to 
the desired loudness.
 - Telephone will not ring.
 1 - Sound will be lowest.
 2 - Sound will be loudest.
NOTE: The unit is properly installed if you pick up the 
handset and hear the dial tone. Otherwise, recheck 
all installation steps.
Wall Mounting
Your speakerphone can also be mounted on a wall plate (not included).
NOTE: To prevent the handset from falling out 
of the cradle while the phone is hanging on 
the wall, you must switch both the handset 
hook and the desk stand to their wall-mount 
positions.
•  On the front of the base, pull the handset hook out of 
the slot. Rotate hook 180 degrees and  ip it from front 
to back. Slide it back into the slot.
•  Turn the base over. Press in on the tabs and remove 
the desk stand from the back of the base.
•   Rotate the stand 180 degrees, and insert the hooks 
marked WALL into the notches marked WALL. Press 
in on the tabs and snap the stand into place.
•  Connect the telephone line cord to the wall jack and 
the phone. If desired, wrap any excess cord around 
the cord hooks as shown.
•  Place the mounting slots over the pins on the wall 
plate, and slide the base down to lock it into place.
Telephone Basics
You can use the telephone by speaking into and listening through the handset, or by 
using the speakerphone.
Receiving a Phone Call
1.  Lift the handset or press the speaker button to answer the call.
2.  Replace the handset in the cradle or press the speaker button to hang up.
Interference Information
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two 
conditions: (1) This device may not cause harmful interference; and (2) This device must accept any 
interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, 
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection 
against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and 
used in accordance with the instructions, may cause harmful interference to radio communications. 
However, there is no guarantee that interference will not occur in a particular installation.
Privacy of Communications may not be ensured when using this product.
If this equipment does cause harmful interference to radio or television reception, which can be 
determined by turning the equipment o  and on, the user is encouraged to try to correct the 
interference by one or more of the following measures:
•  Reorient or relocate the receiving antenna (that is, the antenna for radio or television that is 
“receiving” the interference).
•  Reorient or relocate and increase the separation between the telecommunications equipment and 
receiving antenna.
•  Connect the telecommunications equipment into an outlet on a circuit diff erent from that to which 
the receiving antenna is connected.
If these measures do not eliminate the interference, please consult your dealer or an experienced 
radio/television technician for additional suggestions. Also, the Federal Communications Commission 
has prepared a helpful booklet, “How To Identify and Resolve Radio/TV Interference Problems.” This 
booklet is available from the U.S. Government Printing O  ce, Washington, D.C. 20402. Please specify 
stock number 004-000-00345-4 when ordering copies.
Notice: The changes or modi cations not expressly approved by the party responsible for compliance 
could void the user's authority to operate the equipment.
Hearing Aid Compatibility (HAC)
This telephone system meets FCC standards for Hearing Aid Compatibility.
Licensing
Licensed under US Patent 6,427,009.
FCC RF Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled 
environment. This equipment should be installed and operated with a minimum distance of 20 
centimeters between the radiator and your body. This transmitter must not be co-located or 
operated in conjunction with any other antenna or transmitter.
Memory
You may store information in any of the following memory locations: 0 to 9, A, B, and C . 
See “Storing a Pause in Memory” and “Temporary Tone Dialing” for more information.
Storing a Name and Number in Memory 
1.  Press the store button. The screen displays LOCATION?.
2.  Press the desired memory location (0-9, A, B, C).
NOTE: You may select memory locations by pressing 
review
  or  
buttons to scroll through the memory locations or press the 0 - 9, A, B, C.
3.  Press the store button again to con rm the memory location.
NOTE: If necessary, to erase existing memories, or if you make a mistake, 
use the delete button.
4.  Use the number keys to enter the telephone number (up to 32 digits) and press the 
store button to save. (The unit will not dial a phone number in this mode.) The cursor 
automatically moves to the text line for name entry.
5.  Use the number keys to enter the name of the person associated with the telephone 
number you just entered. More than one letter is stored in each of the number keys.
  For example, to enter the name BILL SMITH, press the 2 key twice for the letter B. Press 
the 4 key 3 times for the letter I. Press the 5 key 3 times for the letter L.
NOTE: The  ashing cursor automatically moves to the next position or 
you may press the 
review
 or  buttons to move the cursor to the next 
position.
  Press the 5 key 3 times for the second letter L. Press the arrow key (4) two times to 
insert a space, and press the 7 key 4 times for the letter S. Press the 6 key once for the 
letter M. Press the 4 key 3 times for the letter I. Press the 8 key for the letter T. Press the 
4 key twice for the letter H. 
6.  Press the store button to save the name.
7.  To enter another name and number in a di erent memory location, return to step 1 
and repeat the process.
Changing a Stored Number
Repeat the storage sequence under “Storing A Name and Number in Memory”, and use 
the delete button to delete the old number before entering the new number.
Erasing a Stored Number
1.  Press the store button.
2.  Press the memory location (0-9, A, B, C) to be erased.
3.  Press the delete button.
Copying Caller ID Memories to User Memory
1.  Press the review  or  buttons to view the caller number and name you want to 
copy.
2.  Press the store button.
3.  Press the memory location (0-9, A, B, C). The number  ashes if there is a number 
already stored in the memory location.
4.  Press the store button to enter the edit mode, and then press the store button again 
to edit the name.
NOTE: You may select a di erent memory location by pressing 
review
  
or  buttons to scroll through the memories or press a number key 
(0-9, A, B, C).
5.  Press the store button to con rm and save, and wait for three seconds to exit. 
NOTE: If the name you want to enter is longer than 12 characters, only 
the  rst 12 characters will be copied into memory.
Storing a Redial Number to Memory
1. Press the store button.
2. Press any key (0-9, or quick call buttons A, B, or C) for the memory location. If there is 
a number already stored in the memory location it will appear on the display. Use the 
review 
 or 
 button to select a di erent location.
3. Press the store button again to con rm.
4. Press the redial button, and then press the store button again.
5. Enter name, if necessary, and then press the store button to con rm. 
NOTE: If you want to edit the number, press the store button again 
within three seconds. When you are  nished, wait three seconds to exit. 
Dialing a Number Stored in Memory While On-hook
1.   Press the dial button.
2.  To select a memory, press any number key (0-9, A, B, C). The number in that memory 
location displays.
NOTE: You may select a di erent memory location by pressing 
review
 
 or  buttons to scroll through the memories or press a number key 
(0-9, A, B, C).
3. Press the speaker button, or pick up the handset to dial the displayed number.
Dialing a Number Stored in Memory
1.  Lift the handset, or press the speaker button.
2.  Press the dial button then press a memory location button.
Cascade Dialing
This process allows you to dial a succession of stored numbers from separate memory 
locations. This is useful when you must dial several sequences of numbers, such as with 
frequent calls via a telephone company long distance provider.
For example  Memory location
Local access number of long distance company    6
Authorization code (ID)    7
Long distance phone number    8
1. Pick up the handset or press speaker.
2. Press dial button, then press number “6” for the memory location.
3. Press dial button, then press number “7” for the memory location.
4. Press dial button, then press number “8” for the memory location.
5. The number dials automatically.
Storing a Pause in Memory
The redial button has dual functionality and becomes a pause button when the store 
button is pressed  rst. It is valid only when storing a number into memory locations. 
Use the redial/pause button to insert a pause when a delay is needed in an automatic 
dialing sequence. For example, when you must dial a 9 to get an outside line or when 
you enter codes to access your long distance company. 
Pre-Dialing
1.  With the handset on the cradle, enter the telephone number you wish to call. The 
Base Layout
Equipment Approval Information
Your telephone equipment is approved for connection to the Public Switched Telephone 
Network and is in compliance with parts 15 and 68, FCC Rules and Regulations and the Technical 
Requirements for Telephone Terminal Equipment published by ACTA.
1  Noti  cation to the Local Telephone Company
On the bottom of this equipment is a label indicating, among other information, the US number 
and Ringer Equivalence Number (REN) for the equipment. You must, upon request, provide this 
information to your telephone company.
The REN is useful in determining the number of devices you may connect to your telephone line 
and still have all of these devices ring when your telephone number is called. In most (but not 
all) areas, the sum of the RENs of all devices connected to one line should not exceed 5. To be 
certain of the number of devices you may connect to your line as determined by the REN, you 
should contact your local telephone company.
A plug and jack used to connect this equipment to the premises wiring and telephone network 
must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A 
compliant telephone cord and modular plug is provided with this product. It is designed to be 
connected to a compatible modular jack that is also compliant. See installation instructions for 
details.
Notes 
• This equipment may not be used on coin service provided by the telephone company.
• Party lines are subject to state tariff s, and therefore, you may not be able to use your own 
telephone equipment if you are on a party line. Check with your local telephone company.
• Notice must be given to the telephone company upon permanent disconnection of your 
telephone from your line.
• If your home has specially wired alarm equipment connected to the telephone line, ensure the 
installation of this product does not disable your alarm equipment. If you have questions about 
what will disable alarm equipment, consult your telephone company or a quali ed installer.
US Number is located on the cabinet bottom.
REN Number is located on the cabinet bottom.
2  Rights of the Telephone Company 
Should your equipment cause trouble on your line which may harm the telephone network, 
the telephone company shall, where practicable, notify you that temporary discontinuance of 
service may be required. Where prior notice is not practicable and the circumstances warrant 
such action, the telephone company may temporarily discontinue service immediately. In case 
of such temporary discontinuance, the telephone company must: (1) promptly notify you of 
such temporary discontinuance; (2) a ord you the opportunity to correct the situation; and (3) 
inform you of your right to bring a complaint to the Commission pursuant to procedures set 
forth in Subpart E of Part 68, FCC Rules and Regulations.
The telephone company may make changes in its communications facilities, equipment, 
operations or procedures where such action is required in the operation of its business and not 
inconsistent with FCC Rules and Regulations. If these changes are expected to a ect the use or 
performance of your telephone equipment, the telephone company must give you adequate 
notice, in writing, to allow you to maintain uninterrupted service.
Making a Phone Call
1.  Lift the handset or press the speaker button. Wait for a dial tone.
2.  Dial the telephone number you want to call.
3.  Replace the handset in the cradle, or press the speaker button to hang up.
Volume
You may adjust the handset and speakerphone volume independently with the 
VOL ( - or + ) buttons. Both handset receiver volume level and speakerphone volume 
level are saved in memory.
Adjusting the Handset Receiver Volume
While using the handset, you can adjust the speaker volume by pressing the 
VOL ( - or + ) buttons. The screen displays  volume.
Adjusting the Speakerphone Volume
While using the speakerphone, you can adjust the speaker volume by pressing the 
VOL ( - or + ) buttons. The screen displays  volume level.
NOTE: Both handset receiver and speakerphone volume return to the 
default setting (low) if the unit's power is reset.
Redial 
You may redial the last number you called by pressing the redial button after you hear a 
dial tone.
NOTE: The redial feature holds the last number (up to 32 digits) that you 
dialed in memory. If you pressed any other numbers after dialing the 
phone number (for example, when accessing a voice-menu system) then 
those numbers are also dialed.
Mute
Use the mute button to interrupt a phone conversation to talk privately with someone 
else in the room. A conversation can be muted while using the speakerphone or 
handset.
1. Press the mute button. The mute indicator illuminates.
2. Press mute again to turn it o .
NOTE: Switching from speakerphone to handset cancels mute.
Flash
Press  ash/exit to activate special features of your telephone network, such as call 
transfer, or special services from your local telephone company, such as call waiting.
Temporary Tone Dialing
If you have pulse (rotary) service and want to access customer calling services (such 
as telebanking and long distance services) that require tone dialing, you can use this 
feature to temporarily change from pulse to tone service. 
After dialing the telephone number and connecting to the customer calling service,
1.  Press and release the *tone button.
2.  When you hang up, the telephone automatically returns to pulse dialing mode.
Speakerphone Basics
Location
Your phone features a speakerphone for ease of use and convenience during a phone 
conversation. At any time during a conversation, you can lift the handset to stop using 
the speakerphone. Likewise, when you are using the handset, press the speaker button 
and place the handset in the cradle to switch to the speakerphone.
For best speakerphone performance, avoid the following:
• 
Areas with high background noise. (The microphone might pick up these sounds and 
prevent the speakerphone from going into the receiving mode when you  nish talking.)
•  Surfaces aff ected by vibration.
•  Recessed areas such as in a corner, under a cupboard, or next to a cabinet, which can 
generate an echo e ect.
Speakerphone Use
Note the following guidelines when using the speakerphone:
•  The speakerphone works similar to a two-way radio in that you can only listen or talk 
at one time.
•  Stay reasonably close to the phone so that you can be clearly heard by the person to 
whom you are talking.
•  You can adjust the speaker volume by pressing the VOL ( - or + ) buttons.
•  The speakerphone indicator light comes on when the speakerphone is in use.
NOTE: Batteries must be installed for the speakerphone to operate.
Caller ID (CID) Features
IMPORTANT: In order to use all of the features of this telephone, you 
must subscribe to two separate services available from your local 
telephone company: the standard Name/Number Caller ID Service 
to know who is calling when the phone rings and Caller ID with Call 
Waiting Service to know who is calling while you are on the phone.
CID Summary Screen
The Summary Screen shows the current time, date, and number of new calls to review. It 
is displayed until any button is pressed.
NOTE: The number of new calls is displayed until all new calls have been 
reviewed.
Receiving and Storing CID Calls
This units receives and displays information transmitted by your local company. This 
information can include the phone number,date, and time ;or the name , phone number, 
date, and time. The unit can store up to 75 calls for later review. When the memory is full, 
a new call automatically replaces the oldest call in memory. The screen displays NEW for 
calls received that have not been reviewed. The screen displays REPT for calls received 
more than once which have not been reviewed. 
telephone number shows in the display.
2.  Lift the handset or press the speaker button and the number automatically dials.
NOTE: Use the delete button to delete an incorrectly entered number. 
Caller ID Display Messages
The following special messages indicate the status of a message or the unit:
BLOCKED CALL   The caller of the incoming call is registered as      
  “Private Number” and their Caller ID information is withheld.
        
  Battery power level is low.
NO CALLS   The caller memory is empty.
START/END  You are at the beginning or the end of the Caller ID memory log.
 PRIVATE CALLER      The incoming call does not have Caller ID service or their service  
  area is not linked to yours. If the screen displays PRIVATE 
  CALLER along with a calling number, the name information for
  that number was not available.
Troubleshooting Tips
No Dial Tone
•  Check all cabling to make sure that all connections are secure and not damaged.
•  Check hook switch: Does it fully extend when handset is lifted from cradle?
No Display
•  Replace the batteries.
•  Check for proper battery installation.
No Information is Shown After the Phone Rings
•  Are you subscribed to Caller ID service from your local telephone company?
•  Be sure to wait until the second ring before answering.
Phone Dials in Pulse with Tone Service
•  Make sure TONE PULSE is set to TONE DIAL.
Phone Won’t Dial Out with Pulse Service
•  Make sure TONE PULSE is set to PULSE DIAL.
Phone Does Not Ring
•  Make sure ringer switch is set to 1 or 2.
•  You may have too many extension phones on your line. Try unplugging some 
extension phones.
•  Check for dial tone. See Troubleshooting Tips for No Dial Tone.
Incoming Voice Volume Low
•   Are other phones off  hook at same time? If so, this is normal condition as volume 
drops when additional phones are used at once.
•  Check the handset receiver or speaker volume.
Memory Dialing
•   Make sure you entered the numbers correctly into memory.
General Product Care
To keep your phone working and looking good, follow these guidelines:
•  Avoid putting it near heating appliances and devices that generate electrical noise 
(for example, motors or  uorescent lamps).
•  DO NOT expose to direct sunlight or moisture.
•  Avoid dropping and other rough treatment to the unit.
•  Clean with a soft cloth. 
•  Never use a strong cleaning agent or abrasive powder because this will damage the 
 nish.
•  Retain the original packaging in case you need to ship it at a later date.
Service
If trouble is experienced with this equipment, for repair or warranty information, please 
contact customer service at 1-800-297-1023. If the equipment is causing harm to the 
telephone network, the telephone company may request that you disconnect the 
equipment until the problem is resolved.
This product may be serviced only by the manufacturer or its authorized service agents. 
Changes or modi cations not expressly approved by Uniden America Corporation could 
void the user’s authority to operate this product. For instructions on how to obtain 
service, refer to the warranty included in this guide or call customer service at 1-800-
297-1023.
Or refer inquiries to:
Uniden America Service 
4700 Amon Carter Blvd.
Forth Worth, TX 76155
Attach your sales receipt to the booklet for future reference or jot down the date this 
product was purchased or received as a gift. This information will be valuable if service 
should be required during the warranty period
.
Purchase Date 
Name of Store
Industry Canada (I.C.) Notice
Terminal equipment
NOTICE:  This equipment meets the applicable Industry Canada Terminal Equipment 
Technical Speci cations. This is con rmed by the registration number. The abbreviation, 
IC, before the registration number signi es that registration was performed based on a 
Declaration of Conformity indicating that Industry Canada technical speci cations were 
met. It does not imply that Industry Canada approved the equipment.
NOTICE:  The Ringer Equivalence Number (REN) for this terminal equipment is marked 
on the equipment itself. The REN assigned to each terminal equipment provides 
an indication of the maximum number of terminals allowed to be connected to a 
Reviewing CID Records
•   Press the review  or buttons to view the call records.
•   Press the review  button to scroll through the call records from the most recent to 
the oldest.
•   Press the review  button to scroll through the call records from the oldest to the 
newest.
•   When a ll of the r ecords hav e been view ed, The screen displays START/END.
Deleting CID Records
•  To delete the record shown in the display, press the delete button once.
•  To delete all records while reviewing, press and hold the delete button for about 
three seconds. The screen displays DELETE ALL?. Press delete again to complete.
Dialing Back
When reviewing Caller ID records, you can dialback the numbers on the display by 
pressing the dial button.
NOTE: If the screen displays PICKUP PHONE, no other changes to 
the number can be made. The information sent from the telephone 
company is known to be a valid number for dialing back (used only 
in very limited areas). Once you pickup the phone, the number is 
automatically dialed.
If You Programmed Your Local Area Code 
1.  Use the review  or  buttons to display the number you want to dial.
2.  Press the dial button.
•  If you see a number with seven digits (i.e. 555-1234), then the call is from within your 
area code. However, this does not guarantee the call is a local call.
•  If you see a number with 11 digits (i.e. 1-234-555-1234), then the call is not from 
within your area code.
NOTE: A timer (10 seconds on-hook and 3 seconds o -hook) located in 
the upper right side of the display will start, letting you know how much 
time is left until the unit returns to the Summary Screen.
3.  If you are at on-hook and the screen displays PICKUP OR ADJ, you can adjust the 
phone number format by pressing the dial button. If the phone is o -hook and the 
screen displays ADJUST, you can adjust the phone number format by pressing the 
dial button. For example, sometimes a 7-digit local number cannot be dialed because 
it requires a 10-digit or 11-digit format. Press the dial button repeatedly to scroll 
through the 7, 10, and 11-digit numbers. 
7-digits:     7-digit telephone number (i.e. 555-5555)
10-digits:    3-digit area code + 7-digit telephone number (i.e. 425-555-5555)
11-digits:    long distance code 1 + 3-digit area code + 7-digit telephone    
    number (i.e. 1-425-555-5555)
4.  To dial the displayed number, and the phone is on-hook, pick up the handset or press 
the speaker button before the timer reaches 0. If the phone is o -hook, wait until the 
time reaches 0. The screen displays NOW DIALING and the number is dialed.
If You Did Not Program Your Local Area Code 
1.  Use the review  or  buttons to display the number you want to dial. You will only 
see 10-digit numbers (i.e. 234- 555-1234).
2.  See step s 2 throug h 4 in the  previous se ction to c omplete the  dialback  process.
Setting Up the Caller ID Menu
You should not plug the telephone into the modular jack while setting up the Caller ID 
menu.
1. Press the menu button to enter the menu feature con guration mode.
# 1. >ENG  FRA  ESP (CID language default English)
# 2. CONTRAST (default level is 3)
# 3. LOCAL AREA CODE
# 4. TONE  PULSE (Default is tone dialing).
2. Press the menu button to scroll through the 4 menu screens.
3. Use the  or  buttons to select the desired setting.
NOTE: You have 20 seconds following an entry before the phone returns 
to the Summary Screen.
Display Language
This adjustment allows you to display the Caller ID prompts in English, French, or Spanish.
1. Press the menu button until the screen displays ENG FRA ESP.
2. Use the review  or  buttons to select ENG, FRA or ESP.
3. Press the menu button again to save.
Contrast
This adjustment allows you to adjust the contrast of the display.
1. Press the menu button until the screen displays CONTRAST.
2. Use the review  or  buttons to select level 1, 2, 3, 4, or 5.
3. Press the menu button again to save.
Local Area Code 
The telephone uses the programmed area codes to determine the number format to 
display when a valid Caller ID signal is received. Numbers that match the local area code 
are displayed as seven digits and are used for dialing back previous numbers. Entering 
your local area code will also help you immediately know if the call is local or long 
distance when viewing the CID records in the display. 
NOTE: If you make a mistake and want to start over again, press the 
delete button to erase all of the digits.
1. Press the menu button until the screen displays LOCAL AREA CODE.
2. Use the number keys to enter the Local Area Code you want.
3. Press the menu button to save.
Dialing Mode
This adjustment allows you to select tone (touch-tone) or pulse (rotary) dialing.
1. Press the menu button until the screen displays TONE   PULSE.
2. Press the review  or buttons to show the current dialing mode. The default is 
TONE dialing.
3. To change the dialing mode, press the review  or  buttons. The display alternates 
between the two modes.
4. Press the menu button again to save.
NOTE: The phone will exit Set Up after 20 seconds if no buttons are 
pressed.
REMINDER: The time and date are programmed automatically when the 
 rst Caller ID record is successfully received after set up.
Model 1360
Call Waiting / Caller ID 
Speakerphone with 
12 Number Memory
User’s Guide
Base
Handset
Handset Cord
Desk stand 
(might be 
attached to the 
base)
2-Wire 
Telephone Line 
Cord
telephone interface. The termination on an interface may consist of any combination 
of devices subject only to the requirement that the sum of the Ringer Equivalence 
Numbers of all the devices does not exceed  ve
.
 
One-year limited warranty
Modular 
telephone 
line jack
Wall plate

NEEDS Battery Door on bottom 
and Strain Relief on bracket 

Visit our website at:   www.uniden.com
Introduction
CAUTION: When using telephone equipment, there are basic 
safety instructions that should always be followed. Refer to the 
IMPORTANT SAFETY INSTRUCTIONS provided with this product 
and save them for future reference.
Short Glossary of Terminology Used in this Manual
Hook switch. The part of the phone that pops up to activate the phone line when the 
handset is lifted from the base.
O -hook. A term used to describe the phone in its active mode when the handset is o   
of the base cradle or when the speaker button is pressed.
On-hook. A term used to describe the phone in an inactive mode.
Before You Begin
Parts Checklist
Make sure your package includes the following items:
Telephone Jack Requirements
To use this phone, you need an RJ11C type modular telephone jack, 
which might look like the one pictured here, installed in your home. 
If you don’t have a modular jack, call your local phone company to 
 nd out how to get one installed.
Important Installation Information
CAUTION: Disconnect the phone cord from the wall outlet 
before installing or replacing the batteries.
•  Never install telephone wiring during a lightning storm.
•  Never touch uninsulated telephone wires or terminals, unless the telephone line 
has been disconnected at the network interface.
•  Use caution when installing or modifying telephone lines.
•   Never install telephone jacks in wet locations unless the jack is speci cally 
designed for wet locations.
•   Temporarily disconnect any equipment connected to the phone, such as faxes, 
other phones, or modems.
delete
button
store
button
mute
button
VOL (+/-) 
buttons
redial/pause
button
 ash/exit
button
menu
button
dial
button
display
*tone 
button
# button
speaker 
button
ringer 
volume 
switch
memory store 
buttons
review (/) 
buttons
Model 1360
Printed in China
Uniden America Corporation
Ft. Worth, TX
SEE  MA RK ING  ON  BO TTO M /  B ACK  OF  PR ODU CT
RISK OF ELECTRIC SHOCK
            DO NOT OPEN
WARNING: TO
PREVENT FIRE OR
ELECTRICAL SHOCK
HAZARD, DO NOT
EXPOSE THIS
PRODUCT  TO RAIN
OR MOISTURE.
THE LIGHTNING
FLASH AND ARROW
HEAD WITHIN THE
TRIANGLE IS A
WARNING SIGN
ALERTING YOU OF
“DANGEROUS
VOLTAGE” INSIDE
THE PRODUCT.
CAUTION: TO REDUCE THE
RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR
BACK). NO USER
SERVICEABLE PARTS INSIDE.
REFER SERVICING TO
QUALIFIED SERVICE
PERSONNEL.
THE EXCLAMATION
POINT WITH IN THE
TRIANGLE I S A
WARNING SIGN
ALERTING Y OU  OF
IMPORTANT
INSTRUCTIO NS
ACCOMPANYING
THE PRODUC T.
CAUTION:
IMPORTANT:  Evidence of original purchase is required for warranty service. 
WARRANTOR: UNIDEN AMERICA CORPORATION (“Uniden”) ELEMENTS OF WARRANTY: 
Uniden warrants, for one year, to the original retail owner, this Uniden Product to be free 
from defects in materials and craftsmanship with only the limitations or exclusions set 
out below. 
WARRANTY DURATION: This warranty to the original user shall terminate and be of no 
further e ec t 12 months after the date of original retail sale. The warranty is invalid if 
the Product is (A) damaged or not maintained as reasonable or necessary, (B) modi ed, 
altered, or used as part of any conversion kits, subassemblies, or any con gurations 
not sold by Uniden, (C) improperly installed, (D) serviced or repaired by someone other 
than an authorized Uniden service center for a defect or malfunction covered by this 
warranty, (E) used in any conjunction with equipment or parts or as part of any system 
not manufactured by Uniden, or (F) installed or programmed by anyone other than as 
detailed by the owner’s manual for this product. 
STATEMENT OF REMEDY: In the event that the product does not conform to this 
warranty at any time while this warranty is in e ect, warrantor will either, at its option, 
repair or replace the defective unit and return it to you without charge for parts, 
service, or any other cost (except shipping and handling) incurred by warrantor or 
its representatives in connection with the performance of this warranty. Warrantor, 
at its option, may replace the unit with a new or refurbished unit. THE LIMITED 
WARRANTY SET FORTH ABOVE IS THE SOLE AND ENTIRE WARRANTY PERTAINING TO 
THE PRODUCT AND IS IN LIEU OF AND EXCLUDES ALL OTHER WARRANTIES OF ANY 
NATURE WHATSOEVER, WHETHER EXPRESS, IMPLIED OR ARISING BY OPERATION OF LAW, 
INCLUDING, BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR 
FITNESS FOR A PARTICULAR PURPOSE. THIS WARRANTY DOES NOT COVER OR PROVIDE 
FOR THE REIMBURSEMENT OR PAYMENT OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. 
Some states do not allow this exclusion or limitation of incidental or consequential 
damages so the above limitation or exclusion may not apply to you.
LEGAL REMEDIES:  This warranty gives you speci c legal rights, and you may also 
have other rights which vary from state to state. This warranty is void outside the 
United States of America and Canada. PROCEDURE FOR OBTAINING PERFORMANCE OF 
WARRANTY: If, after following the instructions in the owner’s manual you are certain that 
the Product is defective, pack the Product carefully (preferably in its original packaging). 
The Product should include all parts and accessories originally packaged with the 
Product. Include evidence of original purchase and a note describing the defect that 
has caused you to return it. The Product should be shipped freight prepaid, by traceable 
means, to warrantor at:
Uniden America Service
4700 Amon Carter Blvd.
Fort Worth, TX 76155
Uniden® is a registered trademark of Uniden America Corporation.
The pictures in this manual are used for examples only. Your actual phone may not look 
exactly like the pictures.





DOC-4a0f408f:

Recommended:
EL25, M20-D - SCHEMA, C 427, UGP 3

Polycom VVX 500, Tynetec Advent XT2, CP920, CP100, 2200-12651-001
  • SoundPoint® IP 650 Quick User Guide Basic Phone Features Customizing Your Phone Applies to phones running SIP 2.2 or later. For detailed information please consult the comprehensive SoundPoint IP 650 User Guide available at: www.polycom.com/support/voicedocumentation/ ©2007 ...

    Model & Doc Type: 2200-12651-001 2

  • Doc No. FM0817 issue 1 Page 1 Advent XT2 Assisted Living Call Management System _________________________________________________________________________________________________ User Manual Manager’s Display Panel (V3) Tynetec operates a policy of ...

    Model & Doc Type: Tynetec Advent XT2 34

  • 1 Owner’s Manual (DRAFT) OLYMPIA OL6010 2.4 GHz WDCT Conference Telephone TABLE OF CONTENTS IMPORTANT SAFETY INFORMATION GETTING STARTED Checklist of Parts Your Conference Telephone POD Base LCD Display on the POD Phone Key Basic Steps to Install Charging the PO ...

    Model & Doc Type: OL6010 25

  • Quick Reference Guide - Yealink – CP920 IP Conference Phone 1 Yealink CP920 IP Conference Phone ABOUT YEALINK CP920 The Yealink CP920 addresses today's audio conferencing challenges and unifies a clear and easy conferencing communication experience for both in ...

    Model & Doc Type: CP920 3

Additional Information:
# Brand Model Document Type/File Pages File Size Last Checked
1 Polycom
IP 650
13 03/02
2 Bell System Practices
50A1
8 06/12
3 Comdial
DXP Plus Series
56 0.31 Mb 12/10
4 Polycom
soundpoint IP series
8 10/03
5 Yealink
SIP-T54S
1126 16/12
6 NEC
SV-8100
1 11/11
7 ClearOne
MAX WIRELESS
1 0.21 Mb 22/10
8 Sony
PCS-1
78 0.71 Mb 28/01
9 Yealink
SIP-T2 Series
1108 23/11
10 Cisco
8800
3 10/02

Popular Right Now:

# Brand Model Document (PDF) Pages Size Check Date
1 Analog Devices
ADSP-TS101 TigerSHARC
410 14.10.2023
2 JVC
GZX900US - Everio Camcorder - 1080i
2 04.03.2024
3 Festo
VABF-S4-A2G2 Series
2 27.02.2024
4 Trane
4DCY4024
25 11.02.2024
5 THERM PRO
TP-60
20 26.10.2023
6 EdilKamin
LOU
125 27.12.2023
7 Oki
PAGE 8p Plus
18 28.09.2023
8 Hamilton Beach
Proctor Silex
4 01.01.2024
9 Quantum
4000
90 22.09.2023
10 Lenovo
53571WU
2 30.09.2023
Operating Impressions, Questions and Answers: