101 West 103rd Street
Indianapolis, IN 46290-1102
© 2008 Thomson Inc.
Trademark(s) ® Registered
Marca(s) Registrada(s)
Model 28802
00026250 (Rev. 0 Dom E)
08-12
Printed in China
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference; and (2) This device
must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur
in a particular installation.
Privacy of Communications may not be ensured when using this product.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna (that is, the antenna for radio or television
that is “receiving” the interference).
• Reorient or relocate and increase the separation between the telecommunications
equipment and receiving antenna.
• Connect the telecommunications equipment into an outlet on a circuit different from
that to which the receiving antenna is connected.
If these measures do not eliminate the interference, please consult your dealer or an
experienced radio/television technician for additional suggestions. Also, the Federal
Communications Commission has prepared a helpful booklet, “How To Identify and
Resolve Radio/TV Interference Problems.” This booklet is available from the U.S.
Government Printing Ofce, Washington, D.C. 20402. Please specify stock number 004-
000-00345-4 when ordering copies.
Notice: The changes or modications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment .
This telephone system meets FCC standards for Hearing Aid Compatibility.
Licensed under US Patent 6,427,009.
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20 centimeters between the radiator and your body. This
transmitter must not be co-located or operated in conjunction with any other antenna or
transmitter.”
For body worn operation, this phone has been tested and meets the FCC RF exposure
guidelines when used with the belt clip supplied with this product. Use of other
accessories may not ensure compliance with FCC RF exposure guidelines.
This telephone is compliant with the DECT 6.0 standard which operates in
the 1.92GHz to 1.93GHz frequency range. Installation of this equipment is
subject to notication and coordination with UTAM. Any relocation of this
equipment must be coordinated through and approved by UTAM. UTAM
may be contacted at 1-800-429-8826.
Your cordless phone uses a digital security system to protect against false ringing,
unauthorized access, and charges to your phone line.
• Avoid sources of noise and heat, such as motors, uorescent lighting, microwave
ovens, heating appliances and direct sunlight.
• Avoid areas of excessive dust, moisture and low temperature.
• Avoid other cordless telephones or personal computers.
• Never install telephone wiring during a lightning storm.
• Never install telephone jacks in wet locations unless the jack is specically designed
for wet locations.
• Never touch non-insulated telephone wires or terminals, unless the telephone line
has been disconnected at the network interface.
• Use caution when installing or modifying telephone lines.
1. Make sure handset is (not in TALK mode) before you replace battery.
2. Remove the battery compartment door.
3. Disconnect the battery plug from the jack inside the battery compartment and remove
the battery pack from the handset.
4. Insert the new battery pack and connect the cord to the jack inside the battery
compartment.
5. Put the battery compartment door back on.
6. Place handset in the base or handset charge cradle to charge.
You can make internal calls between base and cordless handset, or any two
cordless handsets (if you have more than one cordless handset).
1. With the base in idle mode, press the button, the screen displays INT-
NUMBER?.
2.
Use the number keypad to enter the cordless handset number. (1,2,3,4) you want to call.
3. The receiving handset rings and the screen displays BASE.
4. Press the
or
speaker
button of the receiving handset to answer.
1. With the cordless handset in idle mode, press the button, the screen displays INT-
NUMBER?.
2. Use the number keypad to enter “0” for the base.
3.
The base rings and the screen displays the calling cordless handset’s name and number.
4. Pick up the corded handset or press the
speaker
button on the base to answer.
1. With the cordless handset in idle mode, press the button and the screen displays
INT-NUMBER?,
2. Use the number keypad to enter the cordless handset number (1,2,3,4) you want to
call.
3. The receiving handset rings and the screen displays the originating handset's
information.
4. Press the
button or
speaker
button of the receiving handset to answer.
When in intercom mode, a beep tone sounds on the receivers indicating an
incoming call. You must end the intercom before answering the incoming call.
During a telephone call, you may use the intercom/paging function to page another
handset and have an off line, private (two-way) intercom conversation. You may also
have a three-way conference between the external caller and the base/handsets, or
you may transfer the external telephone call to another handset or the base.
1. During an external call, press the button on the base or the button
on the cordless handset, and use the number keypad to enter the handset number
you want to call.
or
speaker
2. When nished, the second handset hangs up to end the intercom call, and your
original telephone conversation resumes.
After receiving an external call, it is possible to include a second handset in the
conversation.
1.
During an external call, press the
button or
speaker
button of another cordless handset
to join call (If Base, pick up the corded handset from the base or pressthe
speaker
button).
2 If either handset or base hangs up, the remaining user continues with the external call.
The function allows you to transfer an external call from the base to a cordless
handset, or from a cordless handset to the base or another cordless handset.
1. During an external call, press the button on the base or button on
the handset to put the external call on hold.
2. Enter the number of the handset that you would like to transfer the call to (0 for base,
1-4 for cordless handset).
3. Once the intercom is established. You may hang up to complete the call transfer.
• Do not burn, disassemble, mutilate, or puncture. Like other batteries of this type, toxic
materials could be released which can cause injury.
• To reduce the risk of re or pe rsonal injury, use only the
listed in the Us er’s Guide.
• Keep batteries out of the reach of children.
• Remove batteries if storing over 30 days.
Make sure your package includes the items shown here.
Should your equipment cause trouble on y our line which may harm the telephone
network, the telephone company shall, where practicable, notify you that temporary
discontinuance of service may be required. Where prior notice is not practicable and
the circumstances warrant such action, the telephone company may temporarily
discontinue service immediately. In case of such temporary discontinuance, the
telephone company must: (1) promptly notify you of such temporary discontinuance;
(2) afford you the opportunity to correct the situation; and (3) inform you of your right
to bring a complaint to the Commission pursuant to procedures set forth in Subpart E
of Part 68, FCC Rules and Regulations.
The telephone company may make changes in its communications facilities,
equipment, operations or procedures where such action is required in the operation
of its business and not inconsistent with FCC Rules and Regulations. If these changes
are expected to affect the use or performance of your telephone equipment, the
telephone company must give you adequate notice, in writing, to allow you to
maintain uninterrupted service.
NOTE: The RBRC seal on the battery used in your Thomson Inc. product
indicates that we are participating in a program to collect and recycle the
rechargeable battery (or batteries).
For more information go to the RBRC web site at www.rbrc.org
or call 1-800-8-BATTERY or contact a local recycling center.
• Defects in materials or workmanship.
• One year, from date of purchase.
(The warranty period for rental units begins with the rst rental or 45 days from date
of shipment to the rental rm, whichever comes rst.)
• Provide you with a new unit. The exchange unit is under warranty for the remainder
of the original product’s warranty period.
• Properly pack your unit. Include any cables, etc., which were originally provided with
the product. We recommend using the original carton and packing materials.
• ”Proof of purchase in the form of a bill of sale or receipted invoice which is evidence
that the product is within the warranty period, must be presented to obtain warranty
service.” For rental rms, proof of rst rental is also required. Also print your name
and address and a description of the defect. Send via standard UPS or its equivalent
to:
• Insure your shipment for loss or damage. Thomson Inc. accepts no liability in case of
damage or loss.
• A new unit will be shipped to you freight prepaid.
does not
• Customer instruction. (Your Owner’s Manual provides information regarding
operating instructions and user controls. Any additional information, should be
obtained from your dealer.)
• Installation and setup service adjustments.
• Batteries.
• Damage from misuse or neglect.
• Products which have been modied or incorporated into other products.
• Products purchased or serviced outside the USA.
• Acts of nature, such as but not limited to lightning damage.
• Please complete and mail the Product Registration Card packed with your unit. It will
make it easier to contact you should it ever be necessary. The return of the card is
not required for warranty coverage.
• Some states do not allow the exclusion nor limitation of incidental or consequential
damages, or limitations on how long an implied warranty lasts so the above
limitations or exclusions may not apply to you.
• This warranty gives you specic legal rights, and you also may have other rights that
vary from state to state.
• This warranty does not apply. Contact your dealer for warranty information.
4. Insert the battery pack.
5. Close the battery compartment by pushing the door up until it snaps into place.
6. Place the handset(s) in the charging cradle(s)
Up to 4 cordless handsets can be registered to the same base.
1. Press the button.
2. Press the
5 or 6 button to select REGISTRATION and press the button.
3. Press the
5 or 6 button to select REGISTER and press the button, the
screen displays ENTER PIN (default setting = 0000).
4. Input the correct PIN code and press the
button to begin registration. The
screen displays SEARCHING. Press and hold the button on the base
until the base screen displays REGISTRATION.
SEARCHING
WRONG PIN,
NO BASE
6. After successful registration, (SUCCESSFUL displays on screen).
Set a preferred name to the cordless handset. The default name is HANDSET.
1. Press the button.
2. Press the
5 or 6 button to select SETUP HS and press the button.
3. Press the
5 or 6 button to select HANDSET NAME and press the button.
4. Enter the desired name using the number keypad. (Delete incorrect entries by pressing
the button).
5. Press the
5 or 6 button to move cursor left or right.
6. Press the
button to conrm.
To de-register a handset from the base.
1. Press the
button.
2. Press the
5 or 6 button to select REGISTRATION and press the button.
3. Press the
5 or 6 button to select REMOVE HANDSET and press the button,
the screen displays ENTER PIN (default setting = 0000).
WRONG PIN
4. Input the correct PIN code and press the button.
5. Press the
5 or 6 button to select the cordless handset (1,2,3,4) to remove and press
the button, the screen displays REMOVE HANDSET?.
6. Press the
button to conrm the setting.
7. Press the
button to return to idle mode.
NOT REG
To keep your unit working and looking good, follow these guidelines:
• Avoid dropping the handset, as well as other rough treatment to the phone.
• Clean the phone with a soft cloth.
• Never use strong cleaning agents, paint thinner, abrasive powder, alcohol, or other
chemical products to clean the unit. Doing so will damage the nish.
•
Retain the original packaging in case you need to ship the phone at a later date.
• Periodically clean the charge contacts on the handset and base with a clean
pencil eraser.
• Aluminum siding.
• Foil backing on insulation.
• Heating ducts and other metal construction that can shield radio signals.
• You ’re too close to appliances such as microwaves, stoves, computers, etc.
• Atmospheric conditions, such as strong storms.
• Base is installed in the basement or lower oor of the house.
• Base is plugged into AC outlet with other electronic devices.
• Baby monitor is using the same frequency.
• Handset battery is low.
• You’re out of range of the base.
If trouble is experienced with this equipment, for warranty information, please contact
customer service at . If the equipment is causing harm to the telephone
network, the telephone company may require that you disconnect the equipment until
the problem is resolved.
Any unauthorized repairs, changes or modications not expressly approved by Thomson
Inc. could void the user’s authority to operate this product. For instructions on how to
obtain a replacement unit, refer to the warranty included in this guide or call customer
service at .
Or refer inquiries to:
Attach your sales receipt to this booklet for future reference or jot down the date this
product was purchased or received as a gift. This information will be valuable if service
should be required during the warranty period.
Purchase date
Name of store
1. On the handset charge cradle, plug the AC power adaptor cord into the power jack on
the back of the cradle and the other into an electrical outlet.
2. The charge indicator on the handset charge cradle turns on to indicate the handset
battery is charging.
1. Locate battery and battery door which are packaged together inside a plastic bag and
are separate from the handset.
2. Locate the battery compartment on the back of the handset.
3. Plug the battery pack cord into the jack inside the compartment.
