Specifications:340/340353-18k_instruction.pdf file (13 Sep 2023)
|
SkyLink 18K Transmitter PDF Manual (Updated: Wednesday 13th of September 2023 02:33:12 AM)
Rating: 4.6 (rated by 29 users)
Compatible devices: G6T2, PT-434, FS-433, PS-103, KP-433, ID-318, 4B-201, HW-434.
Recommended Documentation:
1. INTRODUCTION Model 18K In this package, you will find a keyless entry transmitter with 3V lithium batteries and screws. Keyless Entry Transmitter (Batteries inside) Skylink ® Keyless Entry Transmitter 3. TROUBLE SHOOTING Q: Door opener does not reac t after pressing the button on the transmitter. A:- Ensure you hear 3 beeps from the keypad transmitter after entering the default PIN [0,0,0,0], [#], [1],. If you do not hear 3 beeps, that means the PIN you entered is incorrect. Re-enter the correct PIN. - If the red light on the receiver flashes after entering the PIN on the transmitter, but the door opener does not respond, please ensure the red/black wire is successfully connected from the receiver to the wall mounted door control. - Ensure the wires that are previously connected to the wall mounted door control are not loose. - Ensure the keypad transmitter has been programmed to the receiver. Refer to section 2 for how to program a keypad to the receiver. 2. PROGRAM A KEYPAD TO THE RECEIVER You need to do the programming in order to add the keypad transmitter to the receiver. Plug the receiver 18R (sold separately) into an electrical socket. Press and hold the learn button at the left hand side of the receiver. The red LED on the receiver will flash. 1 2 5. KEYPAD OPERATION The backlight comes on and a beep is emitted when any key is pressed. The backlight of the keypad may not be visible when it is too bright outside. When any key is pressed, the next key must be pressed within 5 seconds or the backlight turns off and the sequence is cancelled. You must begin again. If the keypad does not emit a beep when pressed, wait a few seconds and press the key again. For example, if you are changing the PIN number from 0000 to 123456, enter the following sequence, 0000, ,123456, ,123456, . If confirmed, the backlit LED flashes and the unit emits a long beep. *** If you do not hear 3 beeps after the 4-digit PIN, [#] and [assigned door number] is entered, that means you have entered an incorrect PIN, and the keypad transmitter will not operate your garage door. Two 3 volt Lithium type (CR2032) batteries (included). It is time to change the batteries when the backlight no longer appears. + - Battery Compartment 7. BATTERY 4. REMOVE TRANSMITTER FROM THE RECEIVER Press the [4-digit PIN], [#] and [the assigned number of the door] within 5 seconds. The assigned door number can be either 1, 2, 3 or 4. Example: [0][0][0][0][#][3], for door 3. The receiver red LED will go off indicates the programming is completed. To program the keypad to control more than one receiver, repeat process (1) to (4) with different assigned door numbers. 3 4 5 Learn Button If, within one year from date of purchase, this product should become defective (except battery), due to faulty workmanship or materials, it will be repaired or replaced, without charge. Proof of purchase and a Return Authorization are required. 10. WARRANTY 9. FCC This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. 11. CUSTOMER SERVICE If you would like to order Skylink’s products or have difficulty getting them to work, please : 1. visit our FAQ website at www.skylinkhome.com , or 2. email us at [email protected], or 3. call our toll free at 1-800-304-1187 from Monday to Friday, 9 am to 5 pm EST. Fax +800 286-1320 8. ADDITIONAL RECEIVER You can use 18K to control up to 4 garage door openers by adding Skylink ® Garage Door Receiver 18R for each opener. CUSTOMER SERVICE 17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3 Email:[email protected] http://www.skylinkhome.com P/N. 101A290-001 Rev.1 ©2004 SKYLINK GROUP Follow the instructions below to change the PIN. To change your PIN: 1. Enter the current PIN, (factory default PIN 0 0 0 0), press , 2. Enter new 4 to 6 digit PIN, press , 3. Enter new PIN again, press . * * * 6. CHANGE PIN You can delete the transmitter from a receiver. Unplug the receiver from the electrical socket. Pr ess and hold the learn button on the left hand side of the receiver when plugging the receiver into an electrical socket, the red LED on the receiver will flash rapidly. All the transmitters and keypads are deleted. 2 1 1 pc 2.6 x 6 screw 1 pc 2.6 x 12 screw 1 pc 2.6 x 25 screw You can now mount the transmitter on a desired location. Lift up the cover and insert screw above the keypad in the slot provided (a). Remove the battery cover and insert the second screw in the lower slot (b). Tighten all screws. Replace the battery cover, insert and tighten screw (c). (a) (c) (b) 6
Hitachi DVD Player Manual (#U531UY)
DV-PF3A(S), 101, hitachi/dv-pf3as.pdf
marsden Guidance Scales M-610 (#4O4WON)
M-610, 12, marsden/m-610.pdf
Oven Toast'n'wave 721.66292 Instruction, #YXK4ZK
Toast'n'wave 721.66292, 24, kenmore/toast-n-wave-721-66292.pdf
Pioneer Guide: BR-95 (#7WTQK4)
BR-95, 2, pioneer/br-95.pdf
switel Tutorial Scales BH 700 (#9125ML)
BH 700, 4, switel/bh-700.pdf
TracVision Tutorial: M7 (#9W13G9)
M7, 31, tracvision/m7.pdf
Guide (KCV-W354, #NP59EY)
KCV-W354, 6, kocom/kcv-w354.pdf
Speakers Guidance #28811Z
ESB204, 12, element/esb204.pdf
#U45R9O: 109S20 Instruction
109S20, 2, philips/109s20.pdf
Icom Transceiver Manual (#RR1U6M)
IC-290A, 48, icom/ic-290a.pdf
USER’S MANUAL PRESSURE TRANSMITTERS PCE-28, PCE-28.Smart, PCE-28 Ex Safety PC-29A, PC-29B, PCE-28.Modbus DIFFERENTIAL PRESSURE TRANSMITTERS PRE-28, PRE-28.Smart, PRE-28 Ex Safety PR-29A, PR-29B, PRE-28.Modbus Flameproof (Exd) version IO.PCE-28….PC-29.Exd MARCH 201 ...
Model & Doc Type: PCE-28 20
MARMITEK X-10 HOME AUTOMATION PRODUCTSSM10EMARMITEK UNIVERSAL INPUTX10 TRANSMITTERUNIVERSAL X10 SENSOR MODULE ENGLISH• Triggered by a free contact or sensor output voltage, transforms this triggering into X10 command• Transforms every kind of sensors to X10 sensors.• Remote s ...
Model & Doc Type: SM10E 2
11.12Technical manualMain featuresNon-contact lling level measurement• in liquids up to 5m• in bulk materials up to 2mProcess temperature range from – 40 °C to +85 °CAccuracy ≤ 0,2%Integrated evaluation electronic• 3-wire with current signal 0/4…20 mA• 3- ...
Model & Doc Type: Sonicont USN050 45
Help GuideWireless TransmitterWLA-NS7The following explains how to use this transmitter. Select a topic from the navigation pane.Design and specifications are subject to change without notice.Getting startedParts and controlsMaking connectionsConnecting the transmitter and a TVConnecting the transm ...
Model & Doc Type: WLA-NS7 25
# | Brand | Model | Document Type/File | Pages | File Size | Last Checked |
---|---|---|---|---|---|---|
1 | Danfoss | MBS 32R |
2 | 19/02 | ||
2 | Covid | THB-200 |
11 | 18/03 | ||
3 | WAGO | I/O-SYSTEM 750 |
224 | 08/03 | ||
4 | Contrik | CA-HT-smallONE |
16 | 08/03 | ||
5 | LD | WATS 1 |
4 | 13/02 | ||
6 | Sennheiser | 500 Series |
204 | 1.91 Mb | 25/02 | |
7 | Kramer | TP-580CT |
2 | 12/12 | ||
8 | Kramer | KW-11T |
15 | 24/11 | ||
9 | Siemens | miniTek |
53 | 02/03 | ||
10 | Badger Meter | ORION Cellular LTE-M |
32 | 19/02 |
# | Brand | Model | Document (PDF) | Pages | Size | Check Date |
---|---|---|---|---|---|---|
1 | Diablotek | ABYSS |
13 | 1.29 Mb | 14.01.2024 | |
2 | Snapper | ELT120G33AB |
28 | 2.82 Mb | 07.12.2023 | |
3 | Just5 | Freedom X1 |
2 | 26.11.2023 | ||
4 | LinQTab | LQBBS |
10 | 07.03.2024 | ||
5 | Sony | DVW-A500 |
156 | 08.03.2024 | ||
6 | Siren Marine | MTC |
12 | 12.03.2024 | ||
7 | IKEA | HEMNES |
24 | 20.11.2023 | ||
8 | Windchaser | PACR9 |
14 | 23.12.2023 | ||
9 | JVC | 0997TOV*UN*SN |
84 | 12.02.2024 | ||
10 | HoBao | Pro Hyper ST |
34 | 14.02.2024 |