Specifications:375/375030-wvcp250.pdf file (07 Oct 2023)
|
Panasonic WV-CP250 Security Camera PDF Operating Instructions (Updated: Saturday 7th of October 2023 07:53:29 AM)
Rating: 4.7 (rated by 93 users)
Compatible devices: KX-HCM270, WV-SW158, BL-C131, BB-HCM580A, BL-C30CE, WV-S1570L, WV-SF332, WV-SBV131M.
Recommended Documentation:
Copper wire size (AWG) Length of cable (Approx.) CONNECTIONS A. WV-CP250 (220 V - 240 V AC 50 Hz) Connect the power cord to an electrical outlet of 220V - 240V AC 50Hz. Notes: • Connect the power cord firmly. • The power cord should be long enough for panning and tilting. If the cable is too short, the power cord plug may be pulled off the camera when the camera pans or tilts. B. WV-CP254E (12 V DC/24 V AC) The WV-CP254E has an AC/DC compatible input terminal. The 12 V DC or 24 V AC power supply cord can be connected to this termi- nal. The camera detects the power source automatically. 1. 12 V DC Power Supply Connect the power cord to the AC/DC compatible input terminal on the rear panel of the cam- era. (m) (ft) #24 (0.22mm 2 ) 95 314 #22 (0.33mm 2 ) 150 495 #20 (0.52mm 2 ) 255 842 #18 (0.83mm 2 ) 425 1 403 Recommended wire gauge sizes for 24 V AC line Installation of Auto Iris Lens Connector Install the lens connector (YFE4191J100) when using a video drive ALC lens. The installation should be made by qualified service personnel or system installers. Cut the iris control cable at the edge of the lens connector to remove the existing lens connector and then remove the outer cable cover of the sup- plied connector as shown in the diagram. The pin assignment of the lens connector is as fol- lows: Pin 1: Power source; +9 V DC, 50 mA max. Pin 2: Not used Pin 3: Video signal; 0.7 V[p-p]/40 kΩ Pin 4: Shield, ground Pin 3 Pin 4 Pin 2 Rib Pin 1 Mounting the Lens Caution: Before you mount the lens, loosen the focus lock knob, and rotate it clockwise until it stops. If the ring is not at the end, the inner lens or CCD image sensor may be damaged. q Mount the lens by turning it clockwise on the lens mount of the camera. Note: When mounting the C-mount lens on the camera, mount the C-mount adapter by rotating it clockwise in advance. w Connect the lens cable to the auto iris lens connector on the side of the camera. W V - C P 2 5 0 CP250 Lens mount Focus lock knob C-mount adapter (Option) q w Solder the lens cable to the pins of the sup- plied connector. Video Cable 1. It is recommended to use a monitor whose resolution is at least equal to that of the camera. 2. The maximum extensible coaxial cable length between the camera and the moni- tor is shown below. Type of RG-59/U RG-6/U RG-11/U RG-15/U coaxial cable (3C-2V) (5C-2V) (7C-2V) (10C-2V) Recommended (m) 250 500 600 800 maximum cable length (ft) 825 1 650 1 980 2 640 Caution: Connect to 12 V DC (10.5 V-16 V) or 24 V AC (19.5 V-28 V) class 2 power sup- ply only. Make sure to connect the ground- ing lead to the GND terminal when the power is supplied from a 24 V AC power source. !2 Day/Night Mode Selector This function switches the condition of pic- tures from colour to black and white in low light conditions. COLOUR FIX: Colour picture reverts to black-and-white picture when an exter- nal day/night switching signal is received (refer to Day/Night connec- tions). Note: When using this unit with infrared rays or lighting of which colour temperature is 3 000 K or less, select this mode without fail, and short-circuit the Day/Night input terminals if you select the black-and- white picture. (The AUTO mode may cause hunting.) AUTO: The camera selects black-and-white mode if the picture is dark, or colour mode if the picture is bright enough. Notes: • When using this unit with a video servo control lens, you may not switch from the black-and-white mode to the colour mode depending on lens iris. In such a case, operate the lens adjuster to open the aperture. • This function may not be activated auto- matically when a backlight or a strong light source causes excessive contrast in the picture. In such cases, use the Day/Night input terminals. !3 Duration Time Selector This selector is available when the Day/night switch position is 'AUTO'. Switching time (5 sec. or 1 minute ) is selec- table. !4 BW Level Selector Selects the luminance level. This selector is available when the Day/night switch position is 'AUTO'. According to the luminance level, this camera automatically switches the condition of pic- ture from colour to black-and-white, or in reverse. HI: Colour picture switches to black-and- white pictures at approx. 7 lx with F1.2 lens. LOW: Colour picture switches to black-and- white pictures at approx. 5 lx with F1.2 lens. The factory default setting is HI. !5 Video Output Connector (VIDEO OUT) This connector is for connecting with the VIDEO IN connector of the video monitor. Whenever the multiplexed vertical drive (VD2) signal is supplied to this connector, the cam- era synchronization mode is automatically set to Vertical Drive. !6 Power Indicator (POWER) !7 Day/Night Input Terminal (DAY/NIGHT IN/GND) This terminal is used for connecting the cam- era to an external day/night detecting sensor. Terminals opened: colour picture Terminals shortened: black-and-white picture !8 AC Inlet Socket Plug the power cord (supplied as a standard accessory) into this socket and connect it to an AC outlet. !9 AC/DC Compatible Input Terminal (DC 12 V IN/AC 24 V IN) This terminal is for connecting the 12 V DC or 24 V AC power supply cord. Note: Do not exceed the ratings of the volt- age or current when connecting the external device. Copper wire #24 #22 #20 #18 size (AWG) (0.22mm 2 ) (0.33mm 2 ) (0.52mm 2 ) (0.83mm 2 ) Resistance 0.078 0.050 0.030 0.018 Ω/m Resistance 0.026 0.017 0.010 0.006 Ω/ft Resistance of copper wire [at 20 °C (68 °F)] • Calculation of maximum cable length between camera and power supply 10.8 V DC ≤ VA - (R x 0.42 x L) ≤ 16 V DC L : Cable length (m) R : Resistance of copper wire (Ω/m) VA : DC output voltage of power supply unit VA − 12 L standard = (m) 0.42 x R VA − 16 L minimum = (m) 0.42 x R VA − 10.8 L maximum = (m) 0.42 x R 2. 24 V AC Power Supply Connect the power cable to the AC/DC com- patible input terminal on the rear panel of the camera. + – GND 1-L 2-N AC 24V IN DC 12V IN + – GND GND 1-L 2-N AC 24V IN DC 12V IN Be sure to use a 12 V DC or 24 V AC power sup- ply device that complied with safety standards. 1. Loosen the focus lock knob. 2. Adjust the focus lock knob to obtain a focused point while watching the monitor screen. 3. Tighten the focus lock knob. Caution: Tightening the knob by force will cause damage to the knob or deviation of focus. Note: The object may be out of focus when using a source of near-infrared light than using the visible light. FOCUS OR FLANGE-BACK ADJUSTMENT Pick-up device: 752 (H) x 582 (V) pixels, interline transfer CCD Scanning area: 5.59 (H) x 4.68 (V) mm (equivalent to scanning area of 1/3” pick-up tube) Synchronization: internal, line-locked or multiplexed vertical drive (VD2), selectable Scanning system: 2 : 1 interlace Scanning: 625 lines / 50 fields / 25 frames Horizontal: 15.625 kHz Vertical: 50 Hz Horizontal resolution: 480 lines Video output: 1.0 V[p-p] PAL composite 75 Ω / BNC connector Signal-to-noise ratio: 50 dB (min) (at AGC Off, weight On) Electronic light control: equivalent to continuous variable shutter speed between 1/50 s and 1/15 000 s Minimum illumination: 1.0 lx (0.1 foot-candle) at colour mode, 0.15 lx (0.015 foot-candle) at black and white mode with F1.4 lens Aperture: SHARP or SOFT, selectable Lens mount: CS-mount Ambient operating temperature: −10 °C - +50 °C (14°F - 122 °F) Ambient operating humidity: less than 90 % Power source and WV-CP250: 220 V - 240 V AC 50 Hz, 3.9 W power consumption: WV-CP254E: 12 V DC 300 mA 24 V AC 50 Hz, 3.3 W Dimensions (without lens): 70 mm (W) x 55 mm (H) x 118 mm (D) 2-3/4" (W) x 2-3/16" (H) x 4-5/8" (D) Weights (without lens): WV-CP250: 0.460 kg (1.01 lbs) WV-CP254E: 0.450 kg (0.99 lbs) Day/Night selectable COLOUR FIX (→ external terminal active) or AUTO Weights and dimensions indicated are approximate. Specifications are subject to change without notice. SPECIFICATIONS STANDARD ACCESSORIES Operating Instructions (this document) ............................................. 1 pc. The following parts are for installation:Body cap ............................... 1 pc. ALC lens connector (YFE4191J100) .................................................. 1 pc. AC Power Cord (only for WV-CP250) ................................................ 1 pc. OPTIONAL ACCESSORIES Lenses: WV-LA2R8C3B, WV-LA4R5C3B, WV-LA9C3B, WV-LA210C3, WV-LA408C3, WV-LA908C3, WV-LZ61/10, WV-LZ62/2, WV-LZ62/8, WV-LF4R5C3A, WV-LF9C3A, WV-LFY3C3, WV-LFY45C3, WV-LFY9C3, WV-LZ61/15, WV-LZ61/2, WV-LZF61/2 C-mount Adapter: WV-AD20E W V - C P250 CP250 Focus lock knob Loosen Tighten Matsushita Electric Industrial Co., Ltd. Osaka, Japan http://www.panasonic.co.jp/global/ 2003 © Matsushita Electric Industrial Co., Ltd. All rights reserved. Caution for Mounting the Lens The lens mount should be a C-mount or CS-mount (1”-32UN) and the lens weight should be less than 450 g (0.99 lbs). If the lens is heavier, both the lens and camera should be secured by using the supporter. The protrusion at the rear of the lens should be as shown below. C-mount: Less than 13 mm (1/2”) CS-mount: Less than 8 mm (5/16”) Day/Night Connections Connect an optical sensor to the Day/Night Input terminals. • Day/Night Input terminals with a capacity of 5 V DC pull-up input, 0.2 mA or more. OFF: break contacts: colour picture ON: make contacts: black-and-white picture Note: To activate the Day/Night function, set Day/Night Mode Selector to COLOUR FIX. 1. Do not attempt to disassemble the camera. To prevent electric shock, do not remove screws or covers. There are no user serviceable parts inside. Ask a qualified service person for servicing. 2. Handle the camera with care. Do not abuse the camera. Avoid striking, shaking, etc. The camera could be damaged by improper handling or storage. 3. Do not expose the camera to rain or mois- ture, or try to operate it in wet areas. Turn the power off immediately and ask a qualified service person for servicing. Moisture can damage the camera and also create the danger of electric shock. 4. Do not use strong or abrasive detergents when cleaning the camera body. Use a dry cloth to clean the camera when dirty. In case the dirt is hard to remove, use a mild detergent and wipe gently. Afterwards, wipe off the remained part of the detergent in it with a dry cloth. 5. Clean the CCD faceplate with care. Do not clean the CCD with strong or abrasive detergents. Use lens tissue or a cotton tipped applicator and ethanol. 6. Never face the camera towards the sun. Do not aim the camera at bright objects. Whether the camera is in use or not, never aim it at the sun or other extremely bright objects. Otherwise, blooming or smear may be caused. 7. Do not operate the camera beyond the specified temperature, humidity or power source ratings. Use the camera under conditions where tem- perature is between –10 °C - +50 °C (14 °F - 122 °F), and humidity is below 90 %. The input power source is 220 V - 240 V AC 50 Hz for WV-CP250, and 24 V AC 50 Hz or 12 V DC for WV-CP254E. PRECAUTIONS W V - C P 2 5 0 CP250 <WV-CP250> <WV-CP254> Fixing screws Camera mounting screw holes Mount adapter WV- CP250 WV- CP25 BLC ON AGC HI SHARP COCOUR FIX VIDEO HI 1MINATW1ALCINT 5SECATW2ELCLL LOW AUTODCOFF DAY/NIGHT SOFT LOW DAY/ NIGHT GND GND IN VIDEO OUT POWER 1-L 2-L AC 24V IN DC 12V IN DAY/ NIGHT GND IN VIDEO OUT POWER 220-240V E 50Hz 0 !5 !5 !6 !7 !6 !7 !9 !8 e r q w o ut !1 !3 !0 i y !2 !4 MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS q Auto Iris Lens Connector Supplies power and control signals to an auto iris lens (not supplied). w Focus Lock Knob This knob adjusts the back-focal distance or picture focus. e Lens (option) r Mount Adapter The camera mounting screw hole is for mounting the camera onto a mounting brack- et. The camera is originally designed to be mounted from the bottom, however, a top- mounting type is also available. To mount from the top, remove the mount adapter from the bottom of the camera by removing two fixing screws. Attach the mount adapter to the top as shown in the diagram, then mount the camera on the mounting bracket. Make sure that two original screws are used when mounting the mount adapter; longer type screws may damage inner components, too shorter type screws may cause the camera drop. t Synchronization Mode Selector (INT, LL) Selects the camera synchronization mode as either internal sync mode (INT) or line-lock mode (LL). INT: Sets to internal 2:1 interlace. LL: Sets to Line-lock mode. Note: Do not set the switch to the LL posi- tion when supplying 12 V DC to avoid a synchronization error. y Back Light Compensation Mode Selector (BLC ON, OFF) Lets you select the mode according to the position of the object and light conditions on the screen. ON: Select this mode when a strong light such as a spotlight is in the background. OFF: Normal picture The factory default setting is OFF. u AGC Level Selector AGC level can be selected with this selector. AGC automatically controls the gain of Image brightness level. HI: This setting raises more the gain and brightness of images under low light conditions. LOW: Normal position i Detail/Aperture Level Selector (SHARP, SOFT) The detail/aperture level can be selected with this selector. Set it to the desired position while observing the picture on the monitor. SHARP: Normal position. SOFT: Select this position when a Quad System is connected to this camera. o Automatic Light Control/Electronic Light Control Selector (ALC, ELC) Lets you select the mode according to the lens type used. ALC: Select this mode when an auto iris lens (ALC lens) is used with this camera. ELC: Select this mode when a fixed iris lens or manual iris lens is used with this cam- era. !0 Lens Drive Signal Selector (VIDEO, DC) Lets you select the mode according to the type of auto iris lens drive signal to be sup- plied to the lens from the auto iris lens con- nector. VIDEO: Select this mode if you are using a auto iris lens that requires a video drive signal. DC: Select this mode if you are using a auto iris lens that requires a DC drive signal. !1 Auto-Tracing White Balance mode (ATW) Selector The ATW mode can be selected with this selector. ATW1: Normal picture ATW2: ATW in sodium lamp mode Slide the panel to the left until it locks. 1. The following functions are built in. (1) Auto Light Control (ALC)/Electronic Light Control (ELC) (2) Automatic Gain Control (AGC) and Automatic Tracing White Balance (ATW) (3) Camera synchronization mode selec- table between internal (INT), Line-locked (LL) and Multiplexed Vertical Drive (VD2). 2. Minimum Illumination of 1.0 lx (0.1 foot-can- dle) at colour mode, 0.15 lx (0.015 foot-can- dle) at black and white mode with F1.4 lens. FEATURES 3. Signal-to-noise ratio of 50 dB (min) (at AGC OFF, weight ON) 4. Horizontal resolution of 480 lines 5. Auto iris lens control selectable between video signal and DC power supply. 6. Auto black-and-white mode enables the cam- era to switch between colour and black and white picture in response to light input. Model No. WV-CP250 WV-CP254E Colour CCTV Cameras Operating Instructions W V - CP 2 50 CP250 (Lens: Option) PREFACE Panasonic’s WV-CP250/CP254E series digital sig- nal processing colour CCD cameras introduce a new level of high picture quality and high resolu- tion through the use of a 1/3-inch interline transfer CCD image sensor having 752 horizontal pixels (picture elements), and digital signal processing LSI’s. This model offers cutting-edge technology for advanced video surveillance. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and mainte- nance (servicing) instructions in the literature accompanying the appli- ance. The lightning flash with arrowhead symbol, within an equilateral trian- gle, is intended to alert the user to the presence of uninsulated "dan- gerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. WARNING: To prevent fire or electric shock hazard, do not expose this appliance to rain or moisture. The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SER- VICING TO QUALIFIED SERVICE PERSONNEL. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. Ns0503-1103 3TR001752BAA Printed in China Wij verklaren als enige aansprakelijke, dat het product waarop deze verklaring betrekking heeft, voldoet aan de volgende normen of andere normatieve documenten, overeenkomstig de bepalingen van Richtlijnen 73/23/EEC en 89/336/EEC. Vi erklærer os eneansvarlige for, at dette produkt, som denne deklaration omhandler, er i overensstemmelse med standarder eller andre normative dokumenter i følge bestemmelserne i direktivene 73/23/EEC og 89/336/EEC. We declare under our sole responsibility that the prod- uct to which this declaration relates is in conformity with the standards or other normative documents following the provisions of Directives EEC/73/23 and EEC/ 89/336. Vi deklarerar härmed värt fulla ansvar för att den produkt till vilken denna deklaration hänvisar är i överensstämmelse med standarddokument, eller andra normativa dokument som framstölls i EEC-direktiv nr. 73/23 och 89/336. Ilmoitamme yksinomaisella vastuullamme, että tuote, jota tämä ilmoitus koskee, noudattaa seuraavia standardeja tai muita ohjeellisia asiakirjoja, jotka noudattavat direktiivien 73/23/EEC ja 89/336/EEC säädöksiä. Vi erklærer oss alene ansvarlige for at produktet som denne erklæringen gjelder for, er i overensstemmelse med følgende normer eller andre normgivende dokumenter som følger bestemmelsene i direktivene 73/23/EEC og 89/336/EEC. FOR YOUR SAFETY PLEASE READ THE FOL- LOWING TEXT CAREFULLY. WARNING: This apparatus must be earthed. IMPORTANT The wires in this mains lead are coloured in accor- dance with the following code. Green-and-yellow: Earth Blue: Neutral Brown: Live As the colours of the wire in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, pro- ceed as follows. The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol I or coloured green or green-and-yellow. The wire which is coloured blue must be con- nected to the terminal in the plug which is marked with the letter N or coloured black. The wire which is coloured brown must be con- nected to the terminal in the plug which is marked with the letter L. The serial number of this product may be found on the bottom of the unit. You should note the serial number of this unit in the space provided and retain this instruction as a per- manent record of your purchase to aid identification in the event of theft. Model No. Serial No. Turn the power off at the mains to disconnect the main powr for all unit. CAUTION: An ALL-POLE MAINS SWITCH with a contact separation of at least 3 mm in each pole shall be incorpo- rated in the electrical installation of the building. (WV-CP250 only)
Microwave Oven Microwave Oven - #37HC7Z
Microwave Oven, 6, euromaid/microwave-oven.pdf
ISB313CW Radio - #32I679
ISB313CW, 2, ilive/isb313cw.pdf
Nikon Instruction Digital Camera COOLPIX L110 (#NKQ89F)
COOLPIX L110, 73, nikon/coolpix-l110.pdf
User Guide (CR9228, #9RVRXZ)
CR9228, 24, caple/cr9228.pdf
Racks & Stands Instruction #K3O968
Workrite Poise–Dual, 8, workrite/workrite-poise-dual.pdf
Dibal Scales Manual (#3O4CUO)
DPOS400 SERIE, 72, dibal/dpos400-serie.pdf
Tektronix Racks & Stands Manual (#T8J899)
RM4000, 22, tektronix/rm4000.pdf
Haier Tutorial: HSU18VH7 (#GE7C12)
HSU18VH7, 36, haier/hsu18vh7.pdf
Reference Book (PV-BF5605, #713G84)
PV-BF5605, 7, aiwa/pv-bf5605.pdf
Ice Maker User Guide #EKOH43
EI15IM55GS - 15 Inch Ice Maker, 2, electrolux/ei15im55gs-15-inch-ice-maker.pdf
Model: VIS449EColour 25m Long RangeIR Nightvision Camera1. Zoom and Focus Adjustments can be made on the back panel of thecamera. Remove the rubber grommets to reveal the screw adjusters (as shown below). Use a small flat head screwdriver to adjust bothzoom and focus to your required settings.To ens ...
Model & Doc Type: VIS449E 2
Operating InstructionsNetwork CameraModel No. WV-SW390 SeriesWV-SC380 SeriesWV-SC385WV-SC386WV-SW396LOCKWV-SC385OPENThis manual covers the models: WV-SW390 Series (WV-SW396, WV-SW395, WV-SW396E, WV-SW395E) andWV-SC380 Series (WV-SC386, WV-SC385, WV-SC384, WV-SC386E, WV-SC385E, WV-SC384E).Bef ...
Model & Doc Type: WV-SW390 Series 224
TURBO HD PIR Series Turret Camera with EXT Alarm out User Manual User Manual Thank you for purchasing our product. If there are any questions, or requests, do not hesitate to contact the dealer. This manual applies to the models below: Type Model Type I Camera DS-2CE71D0T-PIRLO DS-2C ...
Model & Doc Type: DS-2CE71D0T-PIRLO 14
P/No. : Z6806-0660-01AVAN 05. 09www.samsungtechwin.comwww.samsungcctv.com•SAMSUNG TECHWIN CO., LTD.145-3, Sangdaewon 1-dong, Jungwon-gu, Seongnam-si,Gyeonggi-do 462-703, KoreaTEL : +82-31-740-8137~8141 FAX : +82-31-740-8145•SAMSUNG OPTO-ELECTRONICS AMERICA,INC.ELECTRONIC I ...
Model & Doc Type: SDZ-330 28
# | Brand | Model | Document Type/File | Pages | File Size | Last Checked |
---|---|---|---|---|---|---|
1 | Security Tronix | ST-IP2FWD |
36 | 19/10 | ||
2 | Panasonic | AGDVC15P - DIGITAL VIDEO CAMERA RECO |
96 | 3.35 Mb | 27/12 | |
3 | Siqura | CD820 Series |
2 | 21/11 | ||
4 | Digitus | DN-18600 |
41 | 23/03 | ||
5 | VADDIO | ZOOMSHOT 20 |
30 | 22/04 | ||
6 | GigE | VA GigE Series |
94 | 26/12 | ||
7 | JVC | LST0886-001A |
85 | 25/02 | ||
8 | Orno | OR-AK-1204 |
2 | 18/03 | ||
9 | Bosch | LTC 0465 Series |
4 | 0.97 Mb | 02/01 | |
10 | Axis | 291 1U |
90 | 21/04 |
# | Brand | Model | Document (PDF) | Pages | Size | Check Date |
---|---|---|---|---|---|---|
1 | Icom | IC-M31 |
36 | 07.03.2024 | ||
2 | AWS | SC-501 |
8 | 0.37 Mb | 13.10.2023 | |
3 | SONIQ | QMD90B |
12 | 17.02.2024 | ||
4 | York | YZH02411 |
52 | 06.04.2024 | ||
5 | M-Audio | PROKEYS SONO 61 |
50 | 08.11.2023 | ||
6 | Marshall Electronics | MXL USB .006 |
7 | 15.11.2023 | ||
7 | LG | KG220 |
78 | 23.03.2024 | ||
8 | Hitachi | FXDUO63 |
48 | 1.76 Mb | 12.11.2023 | |
9 | HP | OmniBook 5000 |
56 | 07.12.2023 | ||
10 | TriangleTube | prestige |
15 | 22.02.2024 |