Viking VMOC206SS Manual, Installation Instructions

 @" Centerline to cutout 14-15/16" (379.71 mm)
@" Centerline to hole 14-5/16" (362.73 mm)
5/16" (8.77 mm)
FIGURE 1
Side Spacer (2 required)
Must protrude from edge of cabinet 
cutout towards center as shown.
(2) bottom spacers
24-5/8" width
1-5/8" height
FIGURE 2
Bottom Spacers (2 required).
FIGURE 3
Front of Cabinet
BUILT-IN TRIM KIT 
FLUSH MOUNTING TEMPLATE
FOR CUSTOM SERIES MICROWAVE OVEN
5/16" (8.77 mm)
 @" Cutout Opening Width 29-15/16" (759.42 mm)
CABINET CUTOUT LINE
FLOOR LINE OF CUTOUT OPENING
CENTER LINE
Cutout Opening Height 21-5/16" (542 mm)
1"
(25.4 mm)
UB4
1.   Align the Flush Mounting Template center line with the center of the cabinet. Align 
the Floor Line with the bottom of the cabinet at the desired height. Tape it in place.
2.  Cut the cabinet opening along the three Cabinet Cutout Lines and the Floor Line.
3.  Install two Side Spacers (see FIGURE 1) and two Bottom Spacers (see FIGURE 2) as 
specified in FIGURE 4.
4.  Cut out the Side Spacer Templates (R and L) and align the indicated edge to the 
corresponding Side Spacer (see FIGURE 3). Be careful to align the Floor Line to the 
bottom edges of the Side Spacers.
5.  Predrill two holes indicated “A“ in Side Spacer - R with a /" drill bit.
6.  Predrill two holes indicated ”B“ in Side Spacer - L with a /" drill bit.
7. Remove template from the cabinet. 
The exhaust duct should be aligned with the front of the bottom spacer closest to the 
cabinet opening. The exhaust duct should align left to right with the left and right 
edges of the bottom spacers. The exhaust duct should be secured to the bottom spacer 
with Screw (C).
1-15/16" (50.35 mm)
1-15/16" (49.9 mm)
22-1/16" (561.0 mm)
24-5/8" (625.5 mm)
4"
4"
(1) Bottom Spacer
(2) Bottom Spacer
TOP VIEW
12-1/8" (308.45 mm)
FIGURE 4
Bottom Spacers centered with cabinet cutout
Edges to align Side Spacer Templates (R and L)
Side Spacer - 
L
Side Spacer - 
R
Height Distance Between Holes 
A
 15-3/4" (399.63 mm)
2-13/16"
(71.1 mm)
CABINET CUTOUT LINE
=
"
 Center
line to hole 12-13/16" (324.63 mm)
=
"
 Center
line to cutout 13-7/16" (341.6 mm)
=
"
 Cutout Opening Width 26-15/16" (683.2 mm)
TINSKB145MRR0

• 
  INVENTOR LV4MDI-07

  INVENTOR Handbook: LV4MDI-07 (#54KC22)

  LV4MDI-07, 104, inventor/lv4mdi-07.pdf

• 
  Isomac DIAMANTINA

  #HYJ6LW: DIAMANTINA Guide

  DIAMANTINA, 17, isomac/diamantina.pdf

• 
  Net Media SCE2

  Security Camera Instruction #JIUW9R

  SCE2, 4, net-media/sce2.pdf

• 
  MPMan MP-F72

  Other Reference Book #PO95S6

  MP-F72, 19, mpman/mp-f72.pdf

• 
  Trust 17938

  #32O7VK: 17938 Guide

  17938, 45, trust/17938.pdf

• 
  Epson L1455

  #8OCT37: L1455 Tutorial

  L1455, 233, epson/l1455.pdf

• 
  BT FREESTYLE 65

  BT Telephone Accessories Manual (#3QJPN8)

  FREESTYLE 65, 54, bt/freestyle-65.pdf

• 
  Silvercrest stbd 6 a1

  Keyboard stbd 6 a1 Instruction, #9E4D69

  stbd 6 a1, 116, silvercrest/stbd-6-a1.pdf

• 
  Harman Kardon CITATION 7.0

  Handbook (CITATION 7.0, #176YST)

  CITATION 7.0, 66, harman-kardon/citation-7-0.pdf

• 
  Smeg CS18A-7

  #3YS6CC: CS18A-7 Tutorial

  CS18A-7, 50, smeg/cs18a-7.pdf

• Search YouTube Videos for Viking VMOC206SS Device
• Search Google for Viking VMOC206SS Information
• Search Photo of Viking VMOC206SS in Google Images
• Search Twitter for Viking VMOC206SS News