Specifications:199/199953-ei26ss55gs_installation_instructions.pdf file (11 Oct 2023)
|
Electrolux EI26SS55GS Refrigerator PDF Installation Instructions (Updated: Wednesday 11th of October 2023 04:25:28 AM)
Rating: 4.2 (rated by 35 users)
Compatible devices: RF617, 64150 TK, UK1205SL, LTB1AF28U0, LRB2AF88S, IK 2750 10 RE, S756281KG3, ERN29651.
Recommended Documentation:
This document should only be removed by customer after installation. P/N: 241868802 Not satisfied with the installation of your refrigerator? Please contact the store you purchased it from. Installation Instructions for Side-By-Side Refrigerator 2 3 To Connect Water Supply Line To Ice Maker Inlet Valve 1. Disconnect refrigerator from electric power source. 2. Place end of water supply line into sink or bucket. Turn ON water supply and flush sup- ply line until water is clear. Turn OFF water supply at shutoff valve. 3. Remove plastic cap from water valve inlet and discard cap. 4. If you use copper tubing - Slide brass compression nut, then ferrule (sleeve) onto water supply line. Push water supply line into water valve inlet as far as it will go (¼ inch/6.4 mm). Slide ferrule (sleeve) into valve inlet and finger tighten compression nut onto valve. Tighten another half turn with a wrench; DO NOT over tighten. See Figure 1. If you use stainless steel tubing - The nut and ferrule are already assembled on the tubing. Slide compression nut onto valve inlet and finger tighten compression nut onto valve. Tighten another half turn with a wrench; DO NOT over tighten. See Figure 2. 5. With steel clamp and screw, secure water supply line (copper tubing only) to rear panel of refrigerator as shown. 6. Coil excess water supply line (copper tubing only), about 2½ turns, behind refrigerator as shown and arrange coils so they do not vibrate or wear against any other surface. 7. Turn ON water supply at shutoff valve and tighten any connections that leak. 8. Reconnect refrigerator to electrical power source. 9. To turn ice maker on, lower wire signal arm (side mounted) or set the ice maker’s On/Off power switch to the “I” position (rear mounted). Place In Permanent Position If possible, use a hand truck to position the refrigerator directly in front of its cabinet enclosure. Be careful not to move the refrigerator beyond its water supply (copper tubing) connections. Plug in the power cord, and push the refrigerator straight back into place. Level Refrigerator & Adjust Doors (if necessary) To install toe grille 1 Open both doors. Slide left and right sides of toe grille over lower hinges of refrigerator. 2 While pushing toe grille firmly against cabinet, fasten bottom clips of toe grille to cabinet. 3 Fasten top clips to cabinet. 4 Close the doors. Fasten right and left side clips into groove of bottom hinge. To remove toe grille 1 With both doors closed, unfasten right and left side clips of toe grille from bottom hinge grove. 2 Open both doors. Press firmly on top of toe grille until top of toe grille pops off. 3 Pull toe grille outward towards your body and off of lower hinges. NOTE: Level the unit with the adjustable rollers before leveling the doors. To level the doors using the adjustable lower hinge (some models): 1 Before leveling either door, remove set screw that locks door height into posi- tion. (The door cannot be adjusted without set screw removed.) 2 If the refrigerator door is lower than the freezer door, raise the refrigerator door by turning the adjustment screw counterclockwise using a 7 / 16 inch wrench. (See illustration.) 3 If the freezer door is lower than the refrigerator door, raise the freezer door by turning the adjustment screw counterclockwise using a 7 / 16 inch wrench. (See illustration.) 4 After leveling, verify door stop contacts lower hinge and top of door does not contact upper hinge through full movement of door (from fully closed to fully open). 5 Replace the toe grille by fitting it into place. 5 Remove Internal Shipping Materials Electrolux uses packing foam and tape to secure the internal parts of your refrigerator for shipping. Once the refrigerator is in position, you can remove this material. Problems? Try These Suggestions Operation problems are possible if any of the installation tasks are not completed. Here is a list of things to check for: • Istherefrigerator’spowercordpluggedin? • Istherefrigeratorconnectedtothehouseholdwatersupply? • Ifyouhadtoremovetherefrigeratorandfreezerdoors,didyoureattachwaterandpowerconnectors atthedoorhinges?(SeetheUse&CareGuidefordetailedinstructionsonremovingandreplacing doors.) • IstheicemakerpowerswitchturnedOn? Other possibilities to check: • Isthepowertothereceptacleturnedon? • Isthewaterlterabovethefreshfoodcompartmentfullyseated(seeUse&CareGuidefordetails)? If you still have operation problems after checking these suggestions, please see the “Solutions To CommonProblems”sectioninyourUse&CareGuide. What’s Next? Congratulations. You are ready to begin enjoying your new Electrolux refrigerator. • Tobecomeawareofimportantsafetyinstructionsandlearnhowtooperateyourrefrigerator,please readtheentireUse&CareGuide. • Youmaywanttostartwiththe“NormalOperatingSights&Sounds”sectionoftheGuidetolearn more about what to expect during typical operation. • Pleaseregisteryourproduct.Youcanregisteronlineatwww.electroluxusa.com.oryoucansimply send in the Registration Card. And thank you for choosing Electrolux. 7 8 1 4 6 Adjustable Wrench Socket Wrench Set OR Phillips Head ™ Tools Necessar y: 3/8” Fixed Wrench AND OR 9 Doors Handles are secure and tight Door seals completely to cabinet on all sides Freezer door is level across the top Leveling Refrigerator is level, side to side and tilted 1 / 4 ” (6mm) front to back Toe grille is properly attached to refrigerator Cabinet is setting solid on all corners Electrical Power House power turned on Refrigerator plugged in Ice Maker House water supply connected to refrigerator No water leaks present at all connections - recheck in 24 hours Ice Maker is turned ON Ice&WaterDispenseroperatescorrectly Frontltermustbeushwithlterhousing (some models) Final Checks Shipping material removed Fresh Food and Freezer temperatures set Crisper Humidity controls set Registration Card sent in Installation Checkoff List Prepare The Installation Site Your refrigerator is designed to be part of a built-in kitchen cabinet system. Be sure to coordinate site preparation and installation with your kitchen contractor. Include these minimum guidelines in your site preparation: • Chooseaplacenearagroundedelectricaloutlet. • Donotuseanextensioncordoranadapterplug. • Avoiddirectsunlightandcloseproximitytoarange, dishwasher or other heat source. • Floorshouldbelevelandabletosupportafullyloaded refrigerator. • Therefrigerator’sIce&WaterDispenserrequireswater supply access. • Planforeasyaccesstocountertopswhenremovingfood. • Forcompleteaccesstodrawersandfreezerbaskets, doors must be able to fully open. Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: Sides & Top: 3/8 inch Rear: 1 inch Transport Unpackaged Refrigerator To Site By now, you have already removed your refrigerator’s shipping carton. You may still need to use a hand truck to move it through close spaces or entrances. If the refrigerator is larger than an entrance, consider two options: • Removetheentrancedoorifoneexists. • Removetherefrigeratordoors(seehowinyourUse&CareGuide). When using a hand truck: • Loadrefrigeratorfromsideofcabinetonly. • Donotrunretainingstrapsoverhandles. • Donotover-tightenretainingstraps. • Neveruserefrigeratorhandlestomovetherefrigerator. • Removetapefromdoorsonlyafterunitisinplace. Connect Water Supply Location of these materials may vary depending on your model. NOTE These installation instructions are provided only as a possible customer option. Electrolux recommends that you use a service or kitchen contracting professional to install your refrigerator. WARNING To avoid electric shock, which can cause death or severe personal injury, do not connect your refrigerator to an electrical power source until you have completed Step 3 of these instructions. NOTE Information about cabinetry construction for Electrolux products is available for contractors. Call 1-877-435-3287. CAUTION Room temperatures below 55°F (13°C) or above 110°F (43°C) will impair cooling ability of your refrigerator’s compressor. CAUTION Shifting the refrigerator from side to side may damage flooring. NOTE • Theicemaker’sfillvalvemayoperatenoisilyifthehouseholdwatersupplyisshutoff. • Afterensuringnowaterleaksexistatanyconnection,besuretocheckforleaksagainin24hours. • SeeyourUse&CareGuidefordetailedinformationaboutsettingupandoperatingtheIce& Water Dispensing system. IMPORTANT If you are installing your refrigerator without connecting it to a water supply, makesuretheicemaker’spowerswitchisturnedOff(seetheUse&Care Guideformoredetails). CAUTION • Shiftingtherefrigeratorfromside to side may damage flooring. • Donotblockthetoegrilleon the lower front of your refriger- ator. Sufficient air circulation is essential for proper operation. Before Installing The Water Supply Line, You Will Need: • BasicTools:adjustablewrench,at-bladescrewdriver, and Phillips TM screwdriver • Accesstoahouseholdcoldwaterlinewithwater pressure between 30 and 100 psi. • Awatersupplylinemadeof¼inch(6.4mm)OD,copper or stainless steel tubing. To determine the length of tubing needed, measure the distance from the ice maker inlet valve at the back of the refrigerator to your cold water pipe. Then add approximately 7 feet (2.1 meters), so the refrigerator can be moved out for cleaning (as shown). • Ashutoffvalvetoconnect the water supply line to your household water system. DO NOT use a self-piercing type shutoff valve. • Acompressionnut and ferrule (sleeve) for connecting a copper water supply line to the ice maker inlet valve. WARNING To avoid electric shock, which can cause death or severe personal in- jury, disconnect the refrigerator from electrical power before connecting a water supply line to the refrigerator. CAUTION To Avoid Property Damage: • CopperorStainlessSteelbraidedtubingisrecom- mended for the water supply line. Water supply tubing made of ¼ inch plastic is not recommended to be used. Plastic tubing greatly increases the potential for water leaks, and the manufacturer will not be responsible for any damage if plastic tubing is used for the supply line. • DONOTinstallwatersupplytubinginareaswheretem- peratures fall below freezing. • Chemicalsfromamalfunctioningsoftenercandamagethe ice maker. If the ice maker is connected to soft water, en- sure that the softener is maintained and working properly. IMPORTANT After connecting the water supply, refer to “How to Prime the Water Supply System” for important information about priming an empty water supply system. Your refrigerator’s water supply system includes several tubing lines, a water filter, a water valve, and a water tank. To ensure that your water dispenser works properly, this system must be completely filled with water when your refrigerator is first connected to the household water supply line. Copper water line from household water supply (Includeenough tubing in loop to allow moving refrigerator out for cleaning.) Ferrule (Sleeve) Copper water line WaterValve Valve Inlet Water Valve Bracket Steel Clamp Plastic Water Tubing to Ice Maker Fill Tu be Brass Compression Nut 1 2 Hinge Flange Set Screw (some models) Door Stop Flange Hinge Open Door 7/16”Wrench and 3/32” Hex Key (some models)
Naxa Document Portable Radio NI-3104 (#6294R1)
NI-3104, 2, naxa/ni-3104.pdf
Supermicro Tutorial: Intelligent Switch (#SHFB12)
Intelligent Switch, 913, supermicro/intelligent-switch.pdf
RC-EX25S CD Player - #899VWP
RC-EX25S, 26, jvc/rc-ex25s.pdf
Dualit Kettle Manual (#4F3ZI2)
SOUP KETTLE, 8, dualit/soup-kettle.pdf
#TE49E6: D1021870 User Manual
D1021870, 35, culligan/d1021870.pdf
#JX377O: 005938-0 Document
005938-0, 56, generac-power-systems/005938-0.pdf
PEUGEOT Automobile Manual (#3718ZA)
308, 384, peugeot/308.pdf
JVC DVD Player Manual (#4E2951)
XV-M556TN, 56, jvc/xv-m556tn.pdf
Kubota Guidance: V2003-T-B (#92EXI6)
V2003-T-B, 112, kubota/v2003-t-b.pdf
Rostra Security System Manual (#2I54J4)
250-8950, 2, rostra/250-8950.pdf
† Water hook-up fits in back air clearance when calculating installation depth.If installed against a wall, allow clearance of 14-3/16" on freezer side to remove bin. To remove fresh food pans, remove door bins.Clearance required to remove fresh food full-size pan without disassembling ...
Model & Doc Type: GSS25KGS 2
frigidaire.com28 Cu. Ft. Standard-DepthSignature FeaturesFrench Door RefrigeratorsFGHN2866P F / P / EProduct DimensionsHeight 69-7/8" (Including Hinges & Rollers)Width (Doors) 36"Depth (Including Door) 33-3/8"More Easy-To-Use FeaturesIce MakerQuick Ice delivers up t ...
Model & Doc Type: FGHN2866P 4
Shelleyglas®/Shelleysteel™Service and Installation ManualPlease read this manual completely before attempting to install or operate this equipment! Notify carrier of damage! Inspect all components immediately. See page 2.Refrigerated, Heated and Non-Electrical UnitsEffective ...
Model & Doc Type: KCM-50 16
+ PanasoniC Operating Instructions Refrigerator-Freezer (Household use) English 2-17 Thank you for purchasing this Panasonic product. Please read these instructions carefully before using this product. Please keep this manual for future reference. Included installation Instructions. Deutsch 18 ...
Model & Doc Type: NR-B32FX2 18
# | Brand | Model | Document Type/File | Pages | File Size | Last Checked |
---|---|---|---|---|---|---|
1 | Kenmore | 6002 |
40 | 10/10 | ||
2 | Electrolux | ERN 23800 |
16 | 24/11 | ||
3 | inventum | AP010B |
56 | 10/03 | ||
4 | Sovereign | SR337 |
13 | 16/01 | ||
5 | Haier | A3FE742CMJ |
17 | 16/03 | ||
6 | Beko | GNE60531XN |
207 | 08/01 | ||
7 | TEKNIX | SMF1440B |
26 | 06/12 | ||
8 | Sub-Zero | ICB648PRO |
9 | 28/01 | ||
9 | KitchenAid | KSSO36QTB - 36" - Refrigerator |
26 | 23/12 | ||
10 | Daikin | LRLEQ5AY1(E) |
156 | 24/11 |
# | Brand | Model | Document (PDF) | Pages | Size | Check Date |
---|---|---|---|---|---|---|
1 | Conair | HCT351 |
2 | 1.34 Mb | 15.01.2024 | |
2 | Canon | imageCLASS MF8380Cdw |
31 | 24.03.2024 | ||
3 | Miele | DGC 6300 |
100 | 07.02.2024 | ||
4 | Sony | FDL-PT22/JE |
22 | 1.79 Mb | 25.02.2024 | |
5 | KYMCO | 250 PEOPLE S INJECTION |
1 | 19.12.2023 | ||
6 | Horstmann | HCT 2 |
2 | 0.13 Mb | 22.10.2023 | |
7 | Black & Decker | OR11FC |
7 | 0.35 Mb | 11.01.2024 | |
8 | Ace | 73-250 |
4 | 0.9 Mb | 21.02.2024 | |
9 | Sena | X1 PRO |
26 | 24.02.2024 | ||
10 | Graco | Baby Strollers |
130 | 2.83 Mb | 16.01.2024 |