Home Automation 113A00-2 Operation & User’s Manual

© 2010 Home Automation, Inc.

 

www.homeauto.com

 

Document: 113I00-2, Rev1.0  May 2010

 

 

HAI Omni-Bus 1-Channel Wall Mount Remote     

Model 113A00-2 
User’s Guide 
 

 

 

SPECIFICATIONS 

 
o  For use with HAI Omni-Bus Output devices  
o  Requires an HAI Omni-Bus RF Transceiver on an Omni-Bus 
network 
o  Frequency: 433.92MHz 
o  Range: Up to 30m  
 
INSTALLATION 
Before installing the Wall Mount Remote Control, PROGRAM the 
Wall  Mount Remote Control into the target receiving device. 
Programming is still possible after installation, but might require 
the co-operation of two people if the receiving device is situated 
far away from the Wall Mount Remote Control. 
 
The Wall Mount Remote Control does NOT require ANY wiring. It 
is a self-contained, battery-operated unit.  
 
FUNCTIONS 
To switch a device ON or OFF 
 
 
Press and release the button on the Wall 
Mount Remote Control.  
 
 
 
To DIM a light (when used with an Omni-Bus Dimmer unit) 
 
Press and hold the button on the Wall Mount 
Remote Control.  
 
 
 
 
To RESTORE to a previous light intensity when the light is 
switched OFF (Light Dimmer only) 
Simply press and hold the button on the Wall  Mount 
Remote Control. Release the button as soon as the light 
turns on. 
 
OMNIBUS PROGRAMMING 
See the HAI OMNIBUS Software User Guide for more information 
on how to program the remote control into an Omni-Bus output 
devices using the OMNIBUS Installation Software. 
 
MANUAL PROGRAMMING 
 
1.  Place the receiving device into the programming mode. This 
is normally done by pressing and holding the button on the 
receiving device until its LED starts flashing continuously. 
(See receiving device user guide for more information). 
 
2. 
Press and hold the button on the Wall Mount 
Remote Control for exactly 10 seconds before 
releasing it. Check for a confirmation signal 
from the receiving device. 

(See receiving 

device user manual for more information). 
 
 
3.    Exit the programming mode on the receiving device.  
       (See receiving device user guide for more information). 
 

 

 

OPERATIONAL MODES 

 
The Wall Mount Remote Control has two modes of operation: 
 
TOGGLE MODE (factory default) 
 
In this mode, the LED indicator on the Wall Mount Remote Control 
flashes 3 times when the button is pressed and released. 
Every time the button on the Wall Mount Remote Control is pressed 
and released, it instructs the receiving device to change its state. So 
if the receiving device had been ON, it would now switch OFF or 
vice versa. 
ON/OFF MODE 
 
In this mode, the LED indicator either flashes once or twice when 
the button is pressed and released. 
One flash indicates that the receiving device will be instructed to 
switch ON, regardless of its current state. 
Two flashes indicate that the receiving device will be instructed to 
switch OFF, regardless of its current state. 
 
CHANGING THE OPERATIONAL MODE 
 
Press and hold the channel button on the Wall 
Mount Remote Control until the indicator LED 
turns  on without flashing. (this operation takes 
approximately 20 seconds). Release the button. 
 
 
 
Press and release the button three times rapidly while the LED is 
ON. 
 
If the Wall  Mount Remote Control was in TOGGLE mode, it will 
change to the ON/OFF mode. 
 
If the Wall Mount Remote Control was in the ON/OFF mode, it will 
change to TOGGLE mode. 
 
DELETING A REMOTE CONTROL 
 
A Wall  Mount Remote Control channel programmed into an  
Omni-Bus  receiving device may be deleted from that device by 
following the procedure below: 
 
1.  Place the receiving device into the programming mode. This is 
normally done by pressing and holding the button on the 
receiving device until the receiving device LED starts flashing 
continuously. (See receiving device user guide  for more 
information). 
 
2.   
Press and hold the button on the Wall  Mount 
Remote Control for exactly 14 seconds before 
releasing it. Check for a confirmation signal 
from the receiving device. (See receiving device 
user guide for more information). 
 
 
3.  Exit the programming mode on the receiving device. (See 
receiving device user guide for more information). 
 
 
REMOTE CONTROL BATTERY REPLACEMENT 
 
When the indicator LED does not function when the button is 
pressed, the battery needs to be replaced.  
 
The Wall Mount Remote Control uses one type 23A 12V battery.
  
 
 

® 
 

• 
  Sony VGN-BZ560P28 - VAIO BZ Series

  Laptop VGN-BZ560P28 - VAIO BZ Series User Guide, #4858Y2

  VGN-BZ560P28 - VAIO BZ Series, 2, sony/vgn-bz560p28-vaio-bz-series.pdf

• 
  Dell PowerEdge R510

  Dell Reference Book Server PowerEdge R510 (#2G625Y)

  PowerEdge R510, 14, dell/poweredge-r510.pdf

• 
  ODM Filmatic

  ODM Watch Manual (#E14IA4)

  Filmatic, 10, odm/filmatic.pdf

• 
  MELICONI AD Professional

  User Manual (AD Professional, #IWH1K4)

  AD Professional, 3, meliconi/ad-professional.pdf

• 
  Zanussi ZBB3294

  Guide (ZBB3294, #8F455H)

  ZBB3294, 68, zanussi/zbb3294.pdf

• 
  Airwell CW-AR

  Heat Pump User Guide #S6239Q

  CW-AR, 48, airwell/cw-ar.pdf

• 
  Odys MDV-HD8

  Odys Camcorder Manual (#1SAAQB)

  MDV-HD8, 68, odys/mdv-hd8.pdf

• 
  Marshalltown MIX3

  Guide (MIX3, #F5KLQ3)

  MIX3, 20, marshalltown/mix3.pdf

• 
  Pioneer SA-9500II

  Instruction (SA-9500II, #GYX8J9)

  SA-9500II, 33, pioneer/sa-9500ii.pdf

• 
  Frymaster FTB-350A

  Fryer Document #Y4257T

  FTB-350A, 14, frymaster/ftb-350a.pdf

• Search YouTube Videos for Home Automation 113A00-2 Device
• Search Google for Home Automation 113A00-2 Information
• Search Photo of Home Automation 113A00-2 in Google Images
• Search Twitter for Home Automation 113A00-2 News