Specifications:72/72825-tu12bw.pdf file (21 Nov 2023)
|
Boss Brass & Wind TU-12BW Tuner PDF Owner's Manual (Updated: Tuesday 21st of November 2023 07:26:45 AM)
Rating: 4.7 (rated by 94 users)
Compatible devices: TX-930, TU-2, tu-3, ST-S3000ES, flashpaq 2805, RT-820, SH-D07, TX-9100 KUW.
Recommended Documentation:
*5100004159-01* Thank you, and congratulations on your choice of the BOSS TU-12BW Chromatic Tuner. Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (supplied on a separate sheet). These sections provide important information concerning the proper operation of the unit. Additionally, in order to feel assured that you have gained a good grasp of every feature provided by your new unit, this manual should be read in its entirety. The manual should be saved and kept on hand as a convenient reference. As shipped, the TU-12BW’s batteries are not yet installed. Be sure to read the section “Changing the Batteries,“ and then follow the instructions to install the batteries. Copyright © 2008 BOSS CORPORATION All rights reserved. No part of this publication may be reproduced in any form without the written permission of BOSS CORPORATION. fig.01?????? Normal Tuning (AUTO CHROMATIC Mode) 1. Connect the plug of the included piezo mic to the INPUT jack and mount the piezo mic on the instrument you want to tune. To carry out tuning using the built-in microphone, connect nothing to the INPUT jack and place the TU-12BW close to the instrument. If you have a digital wind controller or an instrument with a built-in mic or pickup, plug its output into the INPUT jack. 2. Press [POWER] to switch the power on. 3. Press [AUTO/MANUAL] to enable the "AUTO" setting (lighting the green indicator). In AUTO CHROMATIC Mode, the TU-12BW automatically displays a note's pitch (the note name) as you play it on the instrument. Most of the time, AUTO is the most convenient mode to use. When you want to practice producing a specific pitch, you may want to use MANUAL mode; in this mode, only the pitch that you specify is detected and displayed. 4. Play a single note on the instrument. While the note is sounding, the name for the note's current pitch is displayed. The meter and Tuning Guide show how far the note is from the correct pitch. 5. Tune the instrument. With the intended note name displayed, tune the instrument so that and on the Tuning Guide light simultaneously and the meter's needle points to 0 (the center position). When the Accu-Pitch feature is on, the tuner makes a beeping sound when the note is stabilized at the correct pitch, informing you that the note is in tune. Training for a Specific Pitch (Tuning in MANUAL Mode) 1. Connect the plug of the included piezo mic to the INPUT jack and mount the piezo mic on the instrument you want to tune. To carry out tuning using the built-in microphone, connect nothing to the INPUT jack and place the TU-12BW close to the instrument. If you have a digital wind controller or an instrument with a built-in mic or pickup, plug its output into the INPUT jack. 2. Press [POWER] to switch the power on. 3. Press [AUTO/MANUAL] to enable the "MANUAL" setting (lighting the red indicator). 4. Press [ ] or [ ] to display the note name for the specific pitch you want to practice and/or tune. 5. Play a single note on the instrument. The meter and Tuning Guide show how far the note is from the correct pitch. 6. Tune the instrument. With the intended note name displayed, adjust the instrument's tuning so that both and on the Tuning Guide are lit and the meter's needle points to 0 (center position). When the Accu-Pitch feature is on, the tuner makes a beeping sound when the note is stabilized at the correct pitch, informing you that the note is in tune. TU-12BW Settings Changing the Reference Pitch for Tuning 1. Hold down [PITCH] and press [ ] or [ ] to choose the reference pitch you want. The indicator flashes. Choose the reference pitch you want by getting it to flash. 2. Release [PITCH] to set the selected reference pitch. This setting is saved in memory when the TU-12BW is powered off. Tuning While Listening to the Reference Tone (Sound Mode) 1. Choose the tuning mode you want to use (AUTO or MANUAL). 2. Press [ ] (Sound) to play the reference tone. 3. Press [ ] or [ ] to light the indicator for the note name you'd like to use as a reference. The sound of the note name shown by the indicator is played. Pressing [ ] and [ ], you can play reference tones in half-step increments over five octaves (C2 to C7). 4. Tune the instrument to the reference tone. When you're using Sound mode, tuning cannot be performed using the built-in mic (the built-in mic is disabled). 5. Press [ ] (Sound) to stop playing the reference tone. Changing the Meter Response Speed (Quick Response Feature) The Quick Response feature increases the speed of the meter's response to the incoming pitch. You may find this handy for some advanced music practice applications. 1. Press [QUICK RESPONSE] to turn the Quick Response feature on/off. Quick Response is activated when the red indicator lights. Calibrating the Meter's Needle Rarely, the meter's needle may drift out of calibration, causing the needle to point slightly off from the 0 position even when the Tuning Guide's and indicators light simultaneously. This can occur over time as the unit is transported, or if the unit is handled in a rough fashion. If this occurs, you can recalibrate the needle using the following procedure. During normal use, the meter's needle almost never drifts out of calibration. To adjust it, be sure to use a small Phillips screwdriver (a 2.3 mm precision screwdriver). 1. Hold down [PITCH] and turn the power on. Confirm whether or not the needle is pointing at the 0 position. 2. If the needle is not pointing to 0, carefully turn the adjustment screw with a small, precision phillips screwdriver (2.3 mm) until the needle points to 0. 3. After completing calibration, press [POWER] to switch off the power. Useful Features Preventing Battery Drain If You Forget to Switch Off the Power (Auto Power Off Feature) When the TU-12BW is turned on and powered by batteries, the power is turned off automatically if approximately 30 minutes passes without any button being pressed. Deactivating the Auto Power Off Feature You can temporarily deactivate the Auto Power Off feature when you power up the TU-12BW. To do so, simultaneously hold down [ ] and [ ] while you press [POWER] to turn on the power. The Auto Power Off feature is always enabled when you switch on the power in the usual way. Using a Tone to Indicate Tuning is Completed (Accu-Pitch Feature) When the Accu-Pitch feature is on, a beeping sound is played when the pitch of the instrument you’re tuning stabilizes within a range of three cents above or below the correct pitch. This sound tells you that the pitch is in tune. Switching the Accu-Pitch Feature On and Off 1. Hold down [ ] (Sound) and press [POWER] to switch on the power. If no sound is heard from the unit as it's powered up, it means that the Accu-Pitch feature has been deactivated. To enable the Accu-Pitch feature, perform the same operation again; if you hear a beeping sound when the power comes on, it means that Accu-Pitch has been enabled. Memory Features Once batteries are installed in the TU-12BW, the settings described below are retained in memory even after the power is switched off. Removing the batteries returns all settings to their factory defaults. Changing the Batteries The BATT. indicator flashes when the batteries begin to run down. Replace the batteries as soon as possible. * When turning the unit upside-down, place it on a soft cloth or the like so as to prevent damage to the panel. 1. Open the battery compartment (located on the bottom of the unit) by sliding the cover toward OPEN. 2. Remove the old batteries from the battery compartment. 3. Insert two of the same type of fresh AAA batteries. * Make sure the “+” and “-” ends of the batteries are oriented correctly. * Do not mix fresh batteries with used ones, or mix batteries of different types. Doing so can result in fluid leakage. 4. Slide the cover of the battery compartment back into place. Specifications * In the interest of product improvement, the specifications and/or appearance of this unit are subject to change without prior notice. fig.01?????? 1. 2. 3. 4. 5. 1. 2. 3. 4. 5. 1. 2. 1. 2. 3. 4. 5. 1. 1. 2. 3. 1. 2. 3. 4. Owner’s Manual QUICK RESPONSE DC IN jack INPUT jack AUTO/MANUAL This changes the tuning mode. Green Indicator: AUTO CHROMATIC mode Red indicator: MANUAL mode (for tuning a single specied pitch) Indicators These show the current note's name (C-B), natural or sharp status (#), the master reference pitch (438-445), and a warning when the battery is low. Connect the AC adaptor (optional BOSS PSA series) here. Use this to turn the reference tone's sound on and o . This allows you to tune an acoustic instrument when it's not convenient to use the included piezo mic. For the best results with the built-in mic, move the TU-12BW as close to the instrument as possible while tuning. Connect devices such as the included piezo mic or a digital instrument you want to tune here. This changes the meter response speed. These change various settings. This changes the settings for the reference pitch. Switches the power on and o . Insert two of the same type of AAA batteries. Meter Adjustment Control (bottom of the unit) Batteries Compartment (bottom of the unit) Speaker Built-in Mic This plays the reference tone and the Accu-Pitch sound. POWER PITCH (Down)/ (Up) (Sound button) Tuning Guide The tuning indicator lights to show how close you are to the target pitch. lights: pitch is at (low) lights: pitch is sharp (high) light simultaneously: in tune (± 3 cents) Needle Meter Setting Original factory settings Tuning mode setting (AUTO or MANUAL) AUTO Reference pitch 440Hz Note name selected in Sound mode C4 Accu-Pitch feature settings ON (enabled) Quick Response feature settings OFF (disable) Tuning Range E0 (20.6Hz) – C8 (4,186.0Hz) Expected battery life under continuous use (carbon) Approximately 15 hours This figure will vary depending on the actual conditions of use. Reference Pitch A4 (438–445Hz) Dimensions 147.5 (W) x 54.0 (D) x 23.9 (H) mm 5-13/16 (W) x 2-1/8 (D) x 1 (H) inches Tuning Accuracy ± 1 cent Weight 205 g, 8 oz (including batteries) Power Supply Dry battery R03 (carbon) or LR03 (alkaline); (AAA) type x 2; DC 3 V AC adaptor DC 9V (PSA series; optional) Accessories Dry battery (R03 (AAA) type) x 2 (carbon), piezo microphone, Owner’s Manual, Soft Case, Holder, Leaflet (“USING THE UNIT SAFELY” and “IMPORTANT NOTES”), Infor- mation Current Draw 12 mA Products of Roland Vielen Dank und herzlichen Glückwunsch zu Ihrer Wahl des chromatischen Stimmgerätes BOSS TU-12BW. Vor dem Betrieb des Gerätes lesen Sie bitte die folgenden aufgeführten Abschnitte sorgfältig durch: „SICHERER BETRIEB DES GERÄTES“ und „WICHTIGE HINWEISE“ (auf einem gesonderten Blatt beigefügt). Diese Abschnitte enthalten wichtige Informationen über die korrekte Bedienung des Gerätes. Um einen vollständigen Überblick über alle Funktionen des Gerätes zu erhalten, sollten Sie diese Bedienungsanleitung vollständig durchlesen. Bewahren Sie die Anleitung an einem sicheren Platz auf und verwenden Sie diese zu Referenzzwecken. Bei Auslieferung sind die Batterien des TU-12BW noch nicht eingelegt. Lesen Sie sich den Abschnitt „Auswechseln der Batterien“ durch, und folgen Sie dann den Anweisungen zum Einlegen der Batterien. Copyright © 2008 BOSS CORPORATION Alle Rechte vorbehalten. Diese Publikation darf weder ganz noch teilweise ohne schriftliche Genehmigung durch die BOSS CORPORATION reproduziert werden. Abb. 01?????? Normales Stimmen (AUTO-CHROMATIC-Modus) 1. Stecken Sie den Stecker des mitgelieferten Piezomikrofons in die INPUT-Buchse und bringen Sie das Piezomikrofon an dem zu stimmenden Instrument an. Wenn Sie Instrumente ohne das eingebaute Mikrofon stimmen möchten, schließen Sie nichts an der INPUT-Buchse an und stellen Sie das TU-12BW nah am Instrument auf. Wenn Sie einen digitalen Wind-Controller oder ein Instrument mit eingebautem Mikrofon oder Tonabnehmer besitzen, verbinden Sie dessen Ausgang mit der INPUT-Buchse. 2. Drücken Sie die [POWER]-Taste um das Gerät einzuschalten. 3. Drücken Sie die [AUTO/MANUAL]-Taste, um die Einstellung „AUTO“ zu aktivieren (die grüne LED leuchtet). Im AUTO-CHROMATIC-Modus zeigt das TU-12BW automatisch die Tonhöhe (den Notennamen) an, wenn Sie einen Ton auf dem Instrument spielen. In den meisten Fällen ist der AUTO-Modus am praktischsten. Wenn Sie das Erzeugen bestimmter Tonhöhen üben möchten, empfiehlt sich die Verwendung des MANUAL-Modus. In diesem Modus wird nur die von Ihnen angegebene Tonhöhe erkannt und angezeigt. 4. Spielen Sie einen einzelnen Ton auf dem Instrument. Während der Ton erklingt, wird der Notenname (die aktuelle Tonhöhe) angezeigt. Die Höhen- und die Richtanzeige zeigen an, wie weit der Ton von der richtigen Tonhöhe entfernt ist. 5. Stimmen Sie das Instrument. Stimmen Sie, während der beabsichtigte Notenname angezeigt wird, das Instrument, bis die Pfeile und der Richtanzeige gleichzeitig leuchten und die Nadel der Höhenanzeige auf 0 zeigt (mittlere Stellung). Wenn die Accu-Pitch-Funktion eingeschaltet ist, ertönt ein Signalton, wenn der Ton auf der richtigen Höhe stabilisiert ist. Daran erkennen Sie, dass der Ton richtig gestimmt ist. Trainieren bestimmter Tonhöhen (Stimmen im MANUAL-Modus) 1. Stecken Sie den Stecker des mitgelieferten Piezomikrofons in die INPUT-Buchse und bringen Sie das Piezomikrofon an dem zu stimmenden Instrument an. Wenn Sie Instrumente ohne das eingebaute Mikrofon stimmen möchten, schließen Sie nichts an der INPUT-Buchse an und stellen Sie das TU-12BW nah am Instrument auf. Wenn Sie einen digitalen Wind-Controller oder ein Instrument mit eingebautem Mikrofon oder Tonabnehmer besitzen, verbinden Sie dessen Ausgang mit der INPUT-Buchse. 2. Drücken Sie die [POWER]-Taste, um das Gerät einzuschalten. 3. Drücken Sie die [AUTO/MANUAL]-Taste, um die Einstellung „MANUAL“ zu aktivieren (die rote LED leuchtet). 4. Wählen Sie mit den Pfeiltasten [ ] bzw. [ ] die Tonhöhe, die Sie üben und/oder stimmen möchten. 5. Spielen Sie einen einzelnen Ton auf dem Instrument. Die Höhen- und die Richtanzeige zeigen an, wie weit der Ton von der richtigen Tonhöhe entfernt ist. 6. Stimmen Sie das Instrument. Ändern Sie, während der beabsichtigte Notenname angezeigt wird, die Stimmung des Instruments so, dass beide Pfeile ( und ) der Richtanzeige leuchten und die Nadel der Höhenanzeige auf 0 zeigt (mittlere Stellung). Wenn die Accu-Pitch-Funktion eingeschaltet ist, ertönt ein Signalton, wenn der Ton auf der richtigen Höhe stabilisiert ist. Daran erkennen Sie, dass der Ton richtig gestimmt ist. Einstellungen am TU-12BW Ändern der Referenztonhöhe für das Stimmen 1. Halten Sie die [PITCH]-Taste gedrückt, und wählen Sie mit den Pfeiltasten [ ] bzw. [ ] die gewünschte Referenztonhöhe aus. Die entsprechende LED blinkt. 2. Lassen Sie die [PITCH]-Taste los, um die ausgewählte Referenztonhöhe einzustellen. Diese Einstellung bleibt beim Ausschalten des TU-12BW gespeichert. Stimmen mit Hilfe von Referenztönen (Tonmodus) 1. Wählen Sie den gewünschten Stimmmodus aus (AUTO oder MANUAL). 2. Drücken Sie die [ ]-Taste (Ton), um den Referenzton zu spielen. 3. Drücken Sie die Pfeiltasten [ ] bzw. [ ], bis die LED des Tons leuchtet, den Sie als Referenzton verwenden möchten. Der Ton, dessen LED leuchtet, wird gespielt. Mit den Pfeiltasten [ ] und [ ] können Sie über fünf Oktaven (C2 bis C7) Referenztöne in Halbtonschritten spielen. 4. Stimmen Sie das Instrument auf den Referenzton. Wenn Sie den Tonmodus verwenden, kann das Stimmen nicht mit Hilfe des eingebauten Mikrofons erfolgen (dieses ist deaktiviert). 5. Drücken Sie die [ ]-Taste (Ton), um die Referenzton-Wiedergabe zu stoppen. Ändern der Reaktionsgeschwindigkeit der Tonhöhenanzeige (Quick-Response-Funktion) Die Quick-Response-Funktion beschleunigt die Reaktion der Tonhöhenanzeige auf das empfangene Signal. Dies kann bei bestimmten anspruchsvollen Musik- Übungsanwendungen praktisch sein. 1. Drücken Sie die [QUICK RESPONSE]-Taste, um die Quick-Response- Funktion ein- oder auszuschalten. Quick Response ist aktiviert, wenn die rote LED leuchtet. Kalibrieren der Nadel der Tonhöhenanzeige In seltenen Fällen kann sich die kalibrierte Nadel der Tonhöhenanzeige verstellen und zeigt dann nicht genau auf die Stellung 0, auch wenn die Pfeile und der Richtanzeige gleichzeitig leuchten. Dies kann im Lauf der Zeit eintreten, wenn das Gerät transportiert oder unsanft gehandhabt wird. In einem solchen Fall können Sie die Nadel mit dem folgenden Vorgang neu kalibrieren. Bei normalem Gebrauch verliert die Nadel der Tonhöhenanzeige fast nie ihre Kalibrierung. Verwenden Sie, um sie einzustellen, einen Kreuzschlitz- Schraubendreher (einen 2,3-mm-Präzisions-Schraubendreher). 1. Halten Sie die [PITCH]-Taste gedrückt, und schalten Sie das Gerät ein. Sehen Sie nach, ob die Nadel genau auf die Stellung 0 zeigt. 2. Wenn die Nadel nicht auf 0 zeigt, drehen Sie vorsichtig mit einem kleinen Präzisions-Kreuzschlitz-Schraubendreher (2,3 mm) die Verstellschraube, bis die Nadel auf 0 zeigt. 3. Drücken Sie nach Abschluss der Kalibrierung die [POWER]-Taste, um das Gerät auszuschalten. Nützliche Funktionen Verhindern von Batterieverbrauch, wenn Sie das Ausschalten vergessen (Auto-Power-Off-Funktion) Wenn das TU-12BW eingeschaltet und über Batterie betrieben wird, schaltet es sich automatisch aus, wenn etwa 30 Minuten vergehen, ohne dass eine Taste gedrückt wird. Deaktivieren der Auto-Power-Off-Funktionen Sie können die Auto-Power-Off-Funktion vorübergehend deaktivieren, wenn Sie das TU-12BW einschalten. Halten Sie dazu die Pfeiltasten [ ] und [ ] gedrückt, während Sie das Gerät mit der [POWER]-Taste einschalten. Die Auto-Power-Off-Funktion ist immer aktiviert, wenn Sie das Gerät auf normale Weise einschalten. Verwenden eines Signals, um das Ende des Stimmvorgangs anzuzeigen (Accu-Pitch-Funktion) Wenn die Accu-Pitch-Funktion eingeschaltet ist, erklingt ein Signalton, wenn sich die Tonhöhe des zu stimmenden Instruments im Bereich von drei Cent über oder unter der richtigen Tonhöhe stabilisiert. Dieses Signal weist Sie darauf hin, dass die Tonhöhe richtig ist. Ein- und Ausschalten der Accu-Pitch-Funktion 1. Halten Sie die [ ]-Taste (Ton) gedrückt, und schalten Sie das Gerät mit der [POWER]-Taste ein. Wenn während des Einschaltens kein Signal ertönt, bedeutet das, dass die Accu-Pitch-Funktion deaktiviert ist. Führen Sie zum Aktivieren der Accu-Pitch-Funktion den gleichen Vorgang erneut aus; wenn Sie beim Einschalten einen Signalton hören, bedeutet das, dass die Accu-Pitch-Funktion aktiviert ist. Speicherfunktionen Wenn in das TU-12BW Batterien eingelegt sind, bleiben die nachstehend beschriebenen Einstellungen auch beim Ausschalten im Speicher erhalten. Beim Entfernen der Batterien werden alle Einstellungen auf ihre Standardwerte zurückgesetzt. Auswechseln der Batterien Die BATT.-LED blinkt, wenn die Batteriespannung nachlässt. Ersetzen Sie die Batterien so bald wie möglich. * Legen Sie das Gerät, wenn Sie es umdrehen, auf ein weiches Tuch oder etwas Ähnliches, um eine Beschädigung des Bedienfelds zu vermeiden. 1. Öffnen Sie das Batteriefach (an der Unterseite des Geräts), indem Sie die Abdeckung in Richtung OPEN (Öffnen) schieben. 2. Entnehmen Sie die alten Batterien aus dem Batteriefach. 3. Legen Sie zwei neue AAA-Batterien desselben Typs ein. * Achten Sie darauf, die Pole „+“ und „-“ der Batterien richtig auszurichten. * Verwenden Sie nicht gleichzeitig neue Batterien und gebrauchte Batterien oder Batterien verschiedenen Typs. Dadurch könnte Batterieflüssigkeit austreten. 4. Schließen Sie die Abdeckung des Batteriefachs wieder. Technische Daten * Änderungen der technischen Daten und des Designs sind möglich und bedürfen keiner vorherigen Ankündigung. * Für Druckfehler wird keine Haftung übernommen. Nous vous remercions d'avoir choisi l’accordeur chromatique BOSS TU-12BW et vous en félicitons. Avant d'utiliser cet appareil, lisez attentivement les sections suivantes : « UTILISATION DE L’APPAREIL DE FAÇON SÉCURISÉE » et « REMARQUES IMPORTANTES » (livrées séparément). Ces sections fournissent d’importantes informations relatives au bon fonctionnement de l’appareil. En outre, pour vous garantir la maîtrise parfaite des différentes fonctions proposées par votre appareil, il est nécessaire de lire ce manuel dans son intégralité. Vous devez conserver ce manuel sous la main afin de pouvoir vous y reporter au besoin. Les piles ne sont pas encore installées sur le TU-12BW livré. Veillez à lire la section « Remplacement des piles » pour suivre la procédure d’installation des piles. Copyright © 2008 BOSS CORPORATION Tous droits réservés. Toute reproduction intégrale ou partielle de cette publication est interdite sous quelque forme que ce soit sans l’autorisation écrite de BOSS CORPORATION. fig.01?????? Accordeur normal (mode AUTO CHROMATIC) 1. Branchez la fiche du micro piézoélectrique inclus sur la prise INPUT et montez le micro piézoélectrique sur l’instrument à accorder. Pour accorder à l’aide du microphone intégré, ne connectez aucun appareil à la prise INPUT et placez le TU-12BW près de l’instrument. Si vous disposez d’un contrôleur de souffle numérique ou d’un instrument équipé d’un micro intégré ou d’un phonocapteur, branchez sa sortie sur la prise INPUT. 2. Pour mettre l’appareil sous tension, appuyez sur [POWER]. 3. Appuyez sur [AUTO/MANUAL] pour activer le paramètre AUTO (le voyant vert s’allume). En mode AUTO CHROMATIC, le TU-12BW affiche automatiquement l’accord d’une note (le nom de la note) lorsque vous la jouez sur l’instrument. La plupart du temps, AUTO est le mode le plus pratique à utiliser. Lorsque vous souhaitez vous entraîner à produire un accord spécifique, vous pouvez utiliser le mode MANUAL ; ainsi, seul l’accord que vous spécifiez est détecté et affiché. 4. Jouez une note sur votre instrument. Lorsque vous jouez la note, le nom de l’accord actuel de la note s’affiche. Le vumètre et le guide d’accord montrent l’écart de la note par rapport au diapason correct. 5. Accordez l’instrument. Une fois que le nom de la note souhaitée est affiché, accordez l’instrument de sorte que et s’allument simultanément sur le guide d’accord et que l’aiguille du vumètre se place sur 0 (position centrale). Lorsque la fonction Accu-Pitch est activée, l’accordeur émet un signal sonore lorsque la note est accordée correctement. Réalisation d’une note spécifique (accordage en mode MANUAL) 1. Branchez la fiche du micro piézoélectrique inclus sur la prise INPUT et montez le micro piézoélectrique sur l’instrument à accorder. Pour accorder à l’aide du microphone intégré, ne connectez aucun appareil à la prise INPUT et placez le TU-12BW près de l’instrument. Si vous disposez d’un contrôleur de souffle numérique ou d’un instrument équipé d’un micro intégré ou d’un phonocapteur, branchez sa sortie sur la prise INPUT. 2. Pour mettre l’appareil sous tension, appuyez sur [POWER]. 3. Appuyez sur [AUTO/MANUAL] pour activer le paramètre MANUAL (le voyant rouge s’allume). 4. Appuyez sur [ ] ou [ ] pour afficher le nom de la note pour l’accord spécifique que vous souhaitez réaliser et/ou régler. 5. Jouez une note sur votre instrument. Le vumètre et le guide d’accord montrent l’écart de la note par rapport au diapason correct. 6. Accordez l’instrument. Une fois que le nom de la note souhaitée est affiché, réglez l’accord de l’instrument afin que et soient tous deux allumés sur le guide d’accord et que l’aiguille du vumètre se place sur 0 (position centrale). Lorsque la fonction Accu-Pitch est activée, l’accordeur émet un signal sonore lorsque la note est accordée correctement. Paramètres du TU-12BW Changement du diapason de référence pour l’accordage 1. Maintenez le bouton [PITCH] enfoncé et appuyez sur [ ] ou [ ] pour choisir le diapason de référence souhaité. Le voyant clignote. Choisissez le diapason de référence voulu. Son voyant clignote lorsqu’il est atteint. 2. Relâchez le bouton [PITCH] pour choisir le diapason de référence sélectionné. Ce paramètre est enregistré en mémoire lors de la mise hors tension du TU-12BW. Accordage lors de l’écoute du son de référence (mode Sound) 1. Choisissez le mode d’accordage à utiliser (AUTO ou MANUAL). 2. Appuyez sur [ ] (Sound) pour écouter la note de référence. 3. Appuyez sur [ ] ou [ ] pour allumer le voyant correspondant à la note que vous souhaitez utiliser comme référence. Le son de la note affichée par le voyant est joué. Si vous appuyez sur [ ] et [ ], vous pouvez lire des notes de référence par demi-tons successifs sur cinq octaves (C2 à C7). 4. Accordez l’instrument sur la note de référence. Lorsque vous utilisez le mode Sound, l’accord ne peut pas être effectué à l’aide du micro intégré (ce dernier est désactivé). 5. Appuyez sur [ ] (Sound) pour arrêter l’écoute de la note de référence. Modification du temps de réponse du vumètre (fonction Quick Response) La fonction Quick Response améliore le temps de réponse du vumètre pour l’accord entrant. Cela peut s’avérer utile pour certaines applications de pratique musicale avancées. 1. Appuyez sur [QUICK RESPONSE] pour activer/désactiver la fonction Quick Response. La fonction Quick Response est activée lorsque le voyant rouge est allumé. Calibrage de l’aiguille du vumètre En de rares occasions, l’aiguille du vumètre peut être décalibrée et venir se placer légèrement en dehors de la position 0 même lorsque les voyants et du guide d’accord s’allument simultanément. Ce phénomène peut se produire au fil du temps si l’appareil est transporté ou s’il est manipulé brutalement. Dans ce cas, vous pouvez recalibrer l’aiguille à l’aide de la procédure suivante. Lors d’une utilisation normale, l’aiguille du vumètre n’est presque jamais décalibrée. Pour l’ajuster, veillez à utiliser un petit tournevis de précision Phillips (de 2,3 mm). 1. Maintenez le bouton [PITCH] enfoncé et mettez l’appareil sous tension. Vérifiez que l’aiguille pointe vers la position 0. 2. Si ce n’est pas le cas, vissez avec soin la vis de réglage à l’aide d’un petit tournevis de précision Phillips (2,3 mm) jusqu’à ce que l’aiguille pointe vers 0. 3. Une fois le calibrage effectué, appuyez sur [POWER] pour mettre l’appareil hors tension. Fonctions utiles Eviter la perte de charge des piles en cas d’oubli de mise hors tension (fonction Auto Power Off) Lorsque le TU-12BW est sous tension et alimenté par piles, le courant est automatiquement coupé si aucun bouton n’est utilisé pendant 30 minutes environ. Désactivation de la fonction Auto Power Off Vous pouvez désactiver temporairement la fonction Auto Power Off lors de la mise sous tension du TU-12BW. Pour ce faire, maintenez simultanément enfoncés les boutons [ ] et [ ] tout en appuyant sur [POWER] pour mettre l’appareil sous tension. La fonction Auto Power Off est toujours activée lors de la mise sous tension de l’appareil. Signal avertissant que l’accordage est terminé (Fonction Accu-Pitch) Lorsque la fonction Accu-Pitch est activée, un signal sonore est émis lorsque le diapason de l’instrument que vous accordez se stabilise dans une plage de trois centièmes au-dessus ou en dessous du diapason correct. Ce signal vous avertit que le diapason est réglé. Activation et désactivation de la fonction Accu-Pitch 1. Maintenez le bouton [ ] (Sound) enfoncé et appuyez sur [POWER] pour mettre l’appareil sous tension. Si aucun son n’est émis par l’appareil lors de sa mise sous tension, la fonction Accu-Pitch a été désactivée. Pour activer la fonction Accu-Pitch, renouvelez l’opération. Si un signal sonore est émis lors de la mise sous tension, la fonction Accu-Pitch a été activée. Fonctions de mémoire Une fois que les piles ont été installées dans le TU-12BW, les réglages décrits ci-dessous sont conservés en mémoire même pendant que l’appareil est hors tension. Le retrait des piles restaure les valeurs d’usine par défaut de tous les paramètres. Remplacement des piles Le voyant BATT. clignote lorsque les piles commencent à s’épuiser. Remplacez-les dès que possible. * Lorsque vous retournez l’appareil, placez-le sur un chiffon doux pour éviter d’endommager le panneau. 1. Ouvrez le compartiment à piles (situé au bas de l’appareil) en faisant glisser le couvercle vers OPEN. 2. Retirez les piles usagées du compartiment à piles. 3. Insérez deux piles neuves de même type (AAA). * Vérifiez que les signes « + » et « - » sont orientés correctement. * Ne mélangez pas des piles neuves avec des piles usagées, ni des piles de types différents. Vous risqueriez de provoquer une fuite de liquide. 4. Remettez en place le couvercle du compartiment à piles. Fiche technique * En vue d’améliorer le produit, ses caractéristiques techniques et/ou son aspect peuvent être modifiés sans avis préalable. Bedienungsanleitung Die Pfeile leuchten, um anzuzeigen, wie nah Sie der Zieltonhöhe sind. Richtanzeige leuchtet: Tonhöhe zu niedrig leuchten gleichzeitig: richtig gestimmt ( ± 3 Cents) leuchtet: Tonhöhe zu hoch Verstellregler für die Tonhöhenanzeige (an der Unterseite) Lautsprecher Schaltet das Gerät ein und aus. Ändert die Reaktionsgeschwindigkeit der Tonhöhenanzeige. QUICK RESPONSE Legen Sie zwei AAA-Batterien desselben Typs ein. Batteriefach (an der Unterseite) Eingebautes Mikrofon (Ton-Taste) DC-IN-Buchse Schließen Sie hier Geräte wie das mitgelieferte Piezomikrofon oder ein digitales Instrument an, das Sie stimmen möchten. INPUT-Buchse AUTO/MANUAL Tonhöhenanzeige Zum Ändern verschiedener Einstellungen. Ändert die Einstellungen für die Referenztonhöhe. Spielt den Referenzton und den Accu-Pitch-Ton. Ändert den Stimmmodus. Grüne LED: AUTO-CHROMATIC-Modus Rote LED: MANUAL-Modus (zum Stimmen einer angegebenen einzelnen Tonhöhe) LEDs Zeigen den Namen des aktuellen Tons (C–B; deutsch: C–H), den normalen oder erhöhten (#) Zustand, die Gesamt-Referenztonhöhe (438–445) sowie eine Warnung bei schwacher Batterie an. Schließen Sie hier den Netzadapter (optional; PSA-Serie von BOSS) an. Hiermit schalten Sie die Tonausgabe des Referenztons ein und aus. Hiermit können Sie ein akustisches Instrument stimmen, wenn dies praktischer ist, als das mitgelieferte Piezomikrofon zu verwenden. Um mit dem eingebauten Mikrofon die besten Ergebnisse zu erzielen, stellen Sie das TU-12BW beim Stimmen so nah wie möglich am Instrument auf. PITCH POWER (Auf)/ (Ab) MERKE MERKE Einstellung Standardeinstellungen Stimmmodus-Einstellung (AUTO oder MANUAL) AUTO Referenztonhöhe 440 Hz Notennamen-Auswahl im Tonmodus C4 Einstellungen der Accu-Pitch-Funktion ON (aktiviert) Einstellungen der Quick-Response-Funktion OFF (deaktiviert) Stimmbereich E0 (20,6 Hz) – C8 (4.186,0 Hz) Maximale Batterielebensdaue r bei Dauerbetrieb (Kohlebatterie) Etwa 15 Stunden Dieser Wert variiert je nach den tatsächlichen Betriebsbedingungen. Referenztonhöhe A4 (438–445 Hz) Abmessungen 147,5 (B) x 54,0 (T) x 23,9 (H) mm 5-13/16 (B) x 2-1/8 (T) x 1 (H) Zoll Stimmgenauigkeit ± 1 Cent Gewicht 205 g, 8 oz (einschließlich Batterien) Stromversorgung 2 Trockenbatterien R03 (Kohle) oder LR03 (Alkali) des Typs AAA; DC 3V 9V-Gleichstrom- Netzadapter (PSA-Serie; optional) Beigefügtes Zubehör 2 Trockenbatterien (R03, Typ AAA) (Kohle), Piezomikrofon, Bedienungsanleitung, Behälter, Halter, Faltblatt („SICHERER BETRIEB DES GERÄTES“ und „WICHTIGE HINWEISE“), Seite „Information“ Durchflussstrom 12 mA MERKE MERKE MERKE MERKE Mode d'emploi Le voyant d’accord s’allume pour indiquer la proximité avec l’accord cible. Guide d’accord s’allume : l’accord est trop bas (bémol) s’allume : l’accord est trop haut (dièse) Bouton de réglage du vumètre (bas de l’appareil) Haut-parleur Met l’appareil sous/hors tension. Modie le temps de réponse du vumètre. QUICK RESPONSE Insérez deux piles de même type (AAA). Compartiment à piles (bas de l’appareil) Micro intégré (Bas) (Haut) (bouton Sound) Prise DC IN Branchez ici un appareil tel que le micro piézoélectrique inclus ou l’instrument numérique ou électrique à accorder. Prise INPUT AUTO/MANUAL Aiguille du vumètre Permettent de modier divers paramètres. Modie les paramètres du diapason de référence. Permet d’écouter la note de référence et le signal sonore Accu-Pitch. Modie le mode d’accordage. Voyant vert : mode AUTO CHROMATIC Voyant rouge : mode MANUAL (pour le réglage de l’accord spécié) Voyants Ils indiquent le nom de la note actuelle (C-B), un état naturel ou aigu (#), le diapason de référence principal (438-445) et un avertissement si la charge des piles est faible. Branchez l’adaptateur secteur (facultatif sur la série BOSS PSA) ici. Permet d’activer et de désactiver le son de la note de référence. Permet d’accorder un instrument acoustique lorsqu’il n’est pas pratique d’utiliser le micro piézoélectrique inclus. Pour obtenir de meilleurs résultats avec le micro intégré, placez le TU-12BW aussi près que possible de l’instrument lors de l’accord. s’allument simultanément : accord correct (± 3 cents) PITCH POWER Réglage Paramètres d’usine d’origine Mode d’accordage (AUTO ou MANUAL) AUTO Diapason de référence 440Hz Nom de note choisi en mode Sound C4 Paramètres de la fonction Accu-Pitch ON (activée) Paramètres de la fonction Quick Response OFF (désactivée) Plage d’accordage E0 (Mi0 - 20,6 Hz) à C8 (Do8 - 4 186 Hz) Durée de vie prévisible des piles en utilisation continue (carbone) Environ 15 heures Ce chiffre varie en fonction des conditions réelles d’utilisation. Diapason de référence A4 (438–445 Hz) Dimensions 147,5 (L) x 54,0 (P) x 23,9 (H) mm Précision d’accordage ± 1 centième Poids 205 g (piles comprises) Alimentation électrique Pile sèche R03 (carbone) ou LR03 (alcaline) ; type AAA x 2; 3 V continu Adaptateur secteur 9 V continu (série PSA ; facultatif ) Accessoires Pile sèche (type R03 (AAA)) x 2 (carbone), microphone piézo, mode d’emploi, Abri, détenteur, livret (« UTILISATION DE L’APPAREIL DE FAÇON SÉCURISÉE » et « REMARQUES IMPORTANTES »), Information Consommation 12 mA TU-12BW_1.fm 1 ページ 2008年10月9日 木曜日 午後6時23分
#IL1V13: BBCC-Q20 Document
BBCC-Q20, 28, zojirushi/bbcc-q20.pdf
#A3211W: 20 Justice Series Guide
20 Justice Series, 140, boston-whaler/20-justice-series.pdf
Argo User Guide: AEI826SH (#419W99)
AEI826SH, 18, argo/aei826sh.pdf
Cooktop Guide #1H55HG
NET8654UC - 800 36" Electric Cookt, 28, bosch/net8654uc-800-36-electric-cookt.pdf
User Manual (ProWash P3000 HOT, #MFXBIV)
ProWash P3000 HOT, 24, target/prowash-p3000-hot.pdf
#4BKU3U: HB37519 Guide
HB37519, 10, creda/hb37519.pdf
Instruction (DISHWASHER, #U97X68)
DISHWASHER, 26, zanussi/dishwasher.pdf
Watch Tutorial #1ZRRX4
5542, 19, casio/5542.pdf
Craftsman Sander Manual (#NRTIO2)
113.2433, 32, sears/113-2433.pdf
32RF50S TV Receiver - #U49OO7
32RF50S, 2, philips/32rf50s.pdf
GUITAR/BASS TUNER SAT100INSTRUCTION MANUALPARTS OF YOUR TUNER AND THEIR OPERATIONBefore use, install the batteries included with the tuner, following the instructions in “BATTERYCHANGE”.Note: The batteries included with the tuner are monitor batteries, and the battery life may be sho ...
Model & Doc Type: SAT100 4
FM STEREOTUNERMR 71CONTENTSTABLE OF CONTENTSOWNER'S MANUALINTRODUCTIONTECHNICAL DESCRIPTIONFRONT PANEL INFORMATIONBACK PANEL INFORMATIONINSTALLATIONCONNECTINGAudio OutputsStereophonic FM MultiplexMonophonic FMRemote AmplifiersOff-The-Air RecordingAntenna ConnectionsOPERATING INSTR ...
Model & Doc Type: MR 71 20
EDX-3Instruction ManualThank you for purchasing your new Alinco accessory.This Instruction manual contains important safety and operating instructions. Please read this manual carefully before using the product and keep it for future reference.Please be aware that EDX-3 is made espe ...
Model & Doc Type: EDX-3 16
N4 PROFESSIONAL GRADE NETWORK RECORDERQuick Guide31138AJCopyright ©2018 OpenEye. All Rights Reserved. Information contained in this document is subject to change without prior notice. OpenEye does its best to provide accurate information but cannot be held responsible for typos or mist ...
Model & Doc Type: N4 2
# | Brand | Model | Document Type/File | Pages | File Size | Last Checked |
---|---|---|---|---|---|---|
1 | Sony | HCD-D11 |
38 | 15/03 | ||
2 | Pioneer | SX-202 |
21 | 09/11 | ||
3 | Sirius Satellite Radio | SCV1 - SIRIUS Backseat TV System Add-on Tuner |
42 | 2.24 Mb | 22/01 | |
4 | Panasonic | WJ-NX400K/G |
30 | 26/11 | ||
5 | Sony | MBX6 |
20 | 14/02 | ||
6 | ENERGY SISTEM | Energy TDT HD5 |
23 | 09/11 | ||
7 | LDG | AT-897 |
13 | 28/01 | ||
8 | Icom | YPL 880 |
12 | 20/10 | ||
9 | Panasonic | WJ-ND200/G |
22 | 23/11 | ||
10 | Pioneer | XV-DV55 |
94 | 09/02 |
# | Brand | Model | Document (PDF) | Pages | Size | Check Date |
---|---|---|---|---|---|---|
1 | Q-See | QSD2316L |
115 | 3.35 Mb | 09.04.2024 | |
2 | Opel | Kadett |
243 | 09.11.2023 | ||
3 | Lenovo | 3113X06 |
4 | 06.10.2023 | ||
4 | HP | Presario All-in-One CQ1-1000 - Desktop PC |
52 | 04.04.2024 | ||
5 | HP | ProLiant StorageWorks NAS 1500s |
152 | 29.11.2023 | ||
6 | AEG Electrolux | SIC 76 |
26 | 02.12.2023 | ||
7 | ABB | ACS880-07 |
40 | 05.04.2024 | ||
8 | Nokia | 5300 - XpressMusic Cell Phone 5 MB |
2 | 24.02.2024 | ||
9 | Chamberlain | door opener |
36 | 3.1 Mb | 30.10.2023 | |
10 | Teka | NFE 900 X |
260 | 08.02.2024 |