Manual, Instructions For Use for Leviton QuickPort USOC Snap-In Connector 41106-R*6 Switch (1 pages)
Data: UPD 21st February 2024
Leviton QuickPort USOC Snap-In Connector 41106-R*6 Switch PDF Instructions For Use (Updated: Wednesday 21st of February 2024 08:41:06 AM)
Rating: 4.9 (rated by 77 users)
Compatible devices: Powerswitch MDS30-AX, decora smart DZ15S, HKSWP-XDX, DECORA PLUS 56021, PowerSwitch DS30-AX, 91A00-1, Decora Plus 5624, Scene Capable Electronic Switch.
Recommended Documentation:
Text Version of Leviton QuickPort USOC Snap-In Connector 41106-R*6 Switch Manual (Summary of Contents)
(Ocr-Read of Document's Main Page, UPD: 21 February 2024)
QuickPort
®
USOC Snap-In Connector
DESCRIPTION
Leviton’s QuickPort USOC Snap-In Connectors feature a
wiring configuration label for quick and easy wiring.
INSTALLATION
1. Remove jacket from cable.
2. Check jack termination label (located on sides of
jack) for wiring standard and associated color codes.
The label also includes jack pin numbers. (Figure 1)
3. Route the wires for termination as shown in
Figure 2.
4. Using a 110-style punchdown tool, seat the wires into
the IDC slots. With the cutting edge of the tool to the
outside, trim the excess wire flush with the jack body.
(Figure 3)
NOTE: Brown pair of UTP not used for this connector.
5. Place the cap over the termination wires for secure
connection and added strain relief. (Figure 4)
6. Insert jack assembly into platform or wallplate. Note
the “UP” position of the jack.
Instructions for Use
QuickPort
®
USOC
Snap-in Connector
41106-R*6
41108-R*8
DI-C00-41106-00A
IMPORTANT INSTRUCTIONS
1.
Read and understand all instructions. Follow all warnings and
instructions marked on the product.
2.
Do not use this product near water—e.g., near a tub, wash basin,
kitchen sink or laundry tub, in a wet basement, or near a
swimming pool.
3.
Never push objects of any kind into this product through
openings, as they may touch dangerous voltages.
4.
SAVE THESE INSTRU
CTIONS.
SAFETY INFORMATION
1.
Never install communications wiring or components during a
lightning storm.
2.
Never install communications components in wet locations
unless the components are designed specifically for use in wet
locations.
3.
Never touch uninsulated wires or terminals unless the wiring has
been disconnected at the network interface.
4.
Use caution when installing or modifying communications wiring
or components.
5. To prevent electrical shock, each opening must be filled with a
module.
2222 - 222nd Street SE
Bothell, WA 98021, USA
Phone: (425) 485-4288
Fax: (425) 483-5270
QuickPort
®
USOC Snap-In Connector
DESCRIPTION
Leviton’s QuickPort USOC Snap-In Connectors feature a
wiring configuration label for quick and easy wiring.
INSTALLATION
1. Remove jacket from cable.
2. Check jack termination label (located on sides of
jack) for wiring standard and associated color codes.
The label also includes jack pin numbers. (Figure 1)
3. Route the wires for termination as shown in
Figure 2.
4. Using a 110-style punchdown tool, seat the wires into
the IDC slots. With the cutting edge of the tool to the
outside, trim the excess wire flush with the jack body.
(Figure 3)
NOTE: Brown pair of UTP not used for this connector.
5. Place the cap over the termination wires for secure
connection and added strain relief. (Figure 4)
6. Insert jack assembly into platform or wallplate. Note
the “UP” position of the jack.
Instructions for Use
QuickPort
®
USOC
Snap-in Connector
41106-R*6
41108-R*8
DI-C00-41106-00A
IMPORTANT INSTRUCTIONS
1.
Read and understand all instructions. Follow all warnings and
instructions marked on the product.
2.
Do not use this product near water—e.g., near a tub, wash basin,
kitchen sink or laundry tub, in a wet basement, or near a
swimming pool.
3.
Never push objects of any kind into this product through
openings, as they may touch dangerous voltages.
4.
SAVE THESE INSTRU
CTIONS.
SAFETY INFORMATION
1.
Never install communications wiring or components during a
lightning storm.
2.
Never install communications components in wet locations
unless the components are designed specifically for use in wet
locations.
3.
Never touch uninsulated wires or terminals unless the wiring has
been disconnected at the network interface.
4.
Use caution when installing or modifying communications wiring
or components.
5. To prevent electrical shock, each opening must be filled with a
module.
2222 - 222nd Street SE
Bothell, WA 98021, USA
Phone: (425) 485-4288
Fax: (425) 483-5270
3
4
1
2
4
5
6
Color Code for
USOC Wiring
Pin
Number
3
4
1
2
4
5
6
Color Code for
USOC Wiring
Pin
Number
Recommended:
23MT2336 - 23" Stereo Tv, CR365GX56, SERIES VA-1012X, K350 - Wireless Keyboard
IPC-6+, A7503, RF-CRDRD, ABY BOX, DUB-1340, Hirschmann RS20 Series
-
MDTM-8907N page 1 of 4MDTM-8907NRevised 10-07Section 10(00-02-0165)DescriptionMurphy's model MDTM89 is an electronic, dual-temperature moni-tor. It monitors two thermocouples, displays the temperature of thethermocouple selected, and has adjustable trip points for each input.A toggle sw ...
Model & Doc Type: Dual Temperature SWICHGAGE MDTM89 4
-
Installation &Operator’s ManualGuide d'Installationet d'UtilisationManual de Instalacióny del OperarioQuestions? Help is just a moment away!Preguntas? La ayuda es justa un momento lejos!Vous avez des questions? Vous n'avez pasbesoin d'aller loin pour trouver de l&ap ...
Model & Doc Type: 01813-1 44
-
To use a terminal or terminal emulation program: 1. After mounting the appliance, connect a terminal or PC running terminal emulation software to the serial port on the back panel of the DSI5100 appliance using the supplied null modem cable. Congure your terminal or terminal ...
Model & Doc Type: DSI5100 2
-
MF877-00 Page 1 Template Revision B, 18-Nov-2016 HPE instructions for this template are available at MF877-01 Product End-of-Life Disassembly Instructions Product Category: Networking Marketing Name / Model [List multip ...
Model & Doc Type: Aruba 2930M 24SR 5
Operating Impressions, Questions and Answers:
