Specifications:231/231298-passport_srx_installation_manual.pdf file (05 Apr 2024)
|
Escort Passport SRX Radar Detector PDF Installation Manual (Updated: Friday 5th of April 2024 03:11:12 PM)
Rating: 4.4 (rated by 42 users)
Compatible devices: Shifter ZR3, X80, Passport 6800, SmartRadar, PASPORT Max, iX Ci PLATFORM, Passport 9500ix, PASSPORT SC55.
Recommended Documentation:
Interior of Vehicle Concealed Display (Optional) 12 Volt Power Line ± Interior of Vehicle External Speaker (Optional) Passport SRX Installation Manual Front Radar Receiver 1 Determine the best location for the radar receiver. The best location is typically under the bumper, or inside the front grill of the vehicle. For the best radar performance, install the radar receiver horizontally, with a clear “view” of the road. 2 Using the built-in mounting holes on the receiver, or the supplied right-angle mounting bracket, mark location. Drill pilot holes in the vehicle if necessary. 3 Mount radar receiver using the supplied hardware. (If right-angle mounting bracket is used, secure radar receiver to the right-angle bracket first, then install bracket with radar receiver to the vehicle.) Note: 1. Do not drill holes in the receiver itself. 2. Thoroughly investigate location before drilling any holes. 3. Keep all cables away from moving parts, and hot surfaces (radiator, hoses, etc.). 4. Do not splice cable. Radar Receiver Cable 1 Connect the receiver cable to the receiver. 2 Route cable to firewall, and secure with zip- ties (included). 3 Route receiver cable into the vehicle’s interior. If there is not a suitable opening, drill a 13/32" or 7/16" hole. 4 Pull cable through firewall, and plug connector into the jack labeled “Front Radar” on the Interface. 5 Pull grommet (located on the receiver cable itself) through the firewall to seal the hole. Use silicone sealant (not supplied) if necessary. Note: 1. Connection between the radar receiver, and the receiver cable, must be located in a dry location under hood. 2. Only drill hole in firewall after thoroughly investigating location first, ensuring no other wires, hoses, etc. will be damaged. 3. Keep all cables away from moving parts, and hot surfaces (radiator, hoses, etc.). 4. Do not splice cable. Display Controller 1 Determine the best location for the Display Controller in the vehicle’s interior. (Consult customer if necessary.) 2 Install Display Controller using supplied velcro, or double-sided tape. 3 Route cable and plug into jack marked “Display” on Interface. Note: 1. Make certain that the Display is clearly visible from the driver’s position, and that the controls can be easily accessed without interfering with normal driving. Front Laser Shifters 1 Determine best location for the Laser Shifters. For optimum performance, install each laser shifter on either side of the front license plate, with a clear “view” of the road. If possible, center each shifter module between the license plate, and the outside edge of the vehicle. (see photo above) 2 Using the supplied mounting bracket, mark location. Drill pilot holes in the vehicle if necessary. 3 Mount the Laser Shifters using the supplied hardware, making sure that each shifter is level to the road. Note: 1. Do not drill holes in the Laser Shifter itself. 2. Thoroughly investigate location before drilling any holes. 3. Keep all cables away from moving parts, and hot surfaces (radiator, hoses, etc.) 4. Do not splice cable. 5. Make certain that each Laser Shifter is level, and has a clear “view” of the road. Laser Shifter Cables 1 Route Laser Shifter cables to firewall, and secure with zip-ties (included). 2 Route both Shifter cables into the vehicle’s interior. If there is not a suitable opening, drill a 13/32" or 7/16" hole. 3 Pull cables through firewall, and plug connectors into Y-adapter. 4 Plug Y-adapter into jack marked “Front Laser/Shifter” on Interface. 5 Pull grommet (located on each cable) through the firewall to seal the hole. Use silicone sealant (not supplied) if necessary. Note: 1. Only drill hole in firewall after thoroughly investigating location first, ensuring no other wires, hoses, etc. will be damaged. 2. Keep all cables away from moving parts, and hot surfaces (radiator, hoses, etc.). 3. Do not splice cable. TEST After all components are installed correctly: 1 Turn Passport on by rotating the volume control knob. 2 Turn vehicle’s ignition to the “on” position. 3 Passport will cycle through a startup sequence. 4 If any error messages come up, see page 21 of the Owner’s Manual for details. Interface 1 Install Interface under the dash using supplied zip-ties. DO NOT MOUNT IN ENGINE COMPARTMENT. 2 Connect black wire (-) to ground, and red- striped wire (+) to a switched 12-volt supply. (If Passport is left in the “on” position, it will automatically power on and off with the igni- tion). Use blue 3M connector (provided) to tap into existing circuit if needed. 3 Radar receiver, front Laser Shifters, rear Laser Shifter, and Display Controller all plug into the Interface. (Be sure to plug all cables into the correct labeled jacks.) A A C E E H G G A C B B B BB D D D F F Vertical Display Alternative The Display Controller can be mounted vertically, such as the side of the center console (volume knob goes at the top). To do so, follow these steps: 1 Carefully remove the standard overlay from the Display Controller. 2 Replace the standard overlay with the optional vertical one found inside the Owner’s Manual. 3 See programming section for changing the text display to read vertically. Rear Laser Shifter 1 Remove two license plate screws, (top or bottom). 2 Mount Laser Shifter to plate using supplied mounting bracket. 3 Route wire through trunk compartment, and into the vehicle’s interior. 4 Insert connector to jack labeled “Rear Laser Shifter” on Interface. Tips 1. Do not block license plate illumination. 2. Do not cover any required license plate information. Installation Alternatives: 1. Can be installed inside the vehicle facing out the rear window. 2. Cable can be routed under vehicle (keep away from hot and moving parts) then brought into the vehicle’s interior. 3. Cable can be cut if necessary for routing. Reconnect and solder each of the three wires, and seal with heat-shrink tubing. Remote Mute/Volume Adjust 1 Determine best location for the Remote Mute Button. 2 Clean surface area. 3 Remove paper backing on the back of the button, and press onto surface. 4 Route cable and plug into jack marked “Mute” on Interface. H
EM15 METROMIX SERIES Amplifier - #2TO71N
EM15 METROMIX SERIES, 44, eden/em15-metromix-series.pdf
Lawn Mower User Guide #6E7KS7
1693706, 6, simplicity/1693706.pdf
Saw Tutorial #67JKC5
PipeCut P400, 40, exact/pipecut-p400.pdf
Stereo Receiver Tutorial #UG7935
AVR-1404, 59, denon/avr-1404.pdf
Metabo Power Tool Manual (#VCX7O5)
SX E 425 TurboTec, 28, metabo/sx-e-425-turbotec.pdf
5.5-ASP Water Pump - #T5912B
5.5-ASP, 8, little-giant/55-asp.pdf
Washer W 431 TX User Guide, #VR7LE5
W 431 TX, 52, indesit/w-431-tx.pdf
Network Router Guide #3YA78W
RFC 2364, 33, creative/rfc-2364.pdf
Attainment Company Voice Recorder Manual (#26MOE3)
Voice Cue, 2, attainment-company/voice-cue.pdf
Whirlpool User Manual: WHED20 (#678E24)
WHED20, 11, whirlpool/whed20.pdf
OWNER’S MANUALThe Whistler Group Corporate Headquarters3604 NW Frontage Rd. • Bentonville, AR 72712Tel 479.273.6012 • Fax 479.273.2927Customer Return Center551 N 13th St. • Rogers, AR 72756Customer Service Tel 800.531.0004www.whistlergroup.comP/N 260028, ©2010 The Whistler Gr ...
Model & Doc Type: PRO-68SE 9
LED LIGHTS(VISUAL DETECTION)K40-1000 models have one red alert LED for radardetection and one bi-color city\highway LED.K40-2000 models have two red alert LED’s forfront/rear radar detection and one bi-colorcity/highway LED.K40-1000P models use a single LED/piezo warning Pod ins ...
Model & Doc Type: 1000 2
GLOBAL POSITIONING SYSTEM AND 360˚ LASER DETECTORUniden’s GPSRD radar detector providespatented artificial intelligence technologywhich calculates your driving patterns to eliminate falsing.UTILIZES MILITARY SATELLITE TECHNOLOGYManual del usuarioSISTEMA DE POSICIÓN GLOBAL Y DETEC ...
Model & Doc Type: UNIDEN 34
Preco Electronics, Inc. 415 N. Maple Grove, Boise, ID 83704 (800) 453-1141 Copyright 2003 Page 1 of 10 370-894-1B Standard PreView tm Operating Manual/Installation Guide Product Description The Standard PreView tm is a solid-state, pulsed radar object detection system d ...
Model & Doc Type: Standard PreView 10
# | Brand | Model | Document Type/File | Pages | File Size | Last Checked |
---|---|---|---|---|---|---|
1 | Beltronics | Bel Pro RX65 |
16 | 1.31 Mb | 11/01 | |
2 | GENEVO | MAX |
7 | 14/12 | ||
3 | Uniden | LRD6499SWS |
28 | 0.68 Mb | 02/03 | |
4 | Rocky Mountain | RMR-C430 |
12 | 0.41 Mb | 20/12 | |
5 | TE-Group | BTST |
36 | 04/10 | ||
6 | Radenso | Pro Series |
12 | 15/01 | ||
7 | Cobra | XRS9960G |
24 | 3.46 Mb | 06/10 | |
8 | Escort | REDLINE 360C |
4 | 01/02 | ||
9 | Cobra | XRS9600 |
22 | 2.44 Mb | 20/03 | |
10 | Whistler | XTR-690SE |
9 | 0.5 Mb | 28/03 |
# | Brand | Model | Document (PDF) | Pages | Size | Check Date |
---|---|---|---|---|---|---|
1 | ChefScape | Chefscape PBL1000 |
44 | 0.46 Mb | 01.03.2024 | |
2 | Parrot | ASTEROID Smart |
152 | 3.12 Mb | 17.01.2024 | |
3 | GE | 28031 |
4 | 1.83 Mb | 26.01.2024 | |
4 | Black Box | IEEE 802.3 |
3 | 0.4 Mb | 29.10.2023 | |
5 | Xcruiser | XDSR385HD |
49 | 29.10.2023 | ||
6 | Mackie | 1604-VLZ PRO |
51 | 30.12.2023 | ||
7 | AIPTEK | AHDH150 |
202 | 18.04.2024 | ||
8 | CANNICE | iblue 8 |
12 | 25.01.2024 | ||
9 | EAW | FR122 |
2 | 0.21 Mb | 07.10.2023 | |
10 | Hughes | DW6000 |
76 | 23.03.2024 |