Data: UPD 2nd October 2023
Manitowoc K00156 Ice Maker PDF Installation Instructions (Updated: Monday 2nd of October 2023 06:22:40 PM)
Rating: 4.6 (rated by 94 users)
Compatible devices: QM 20, K00133, Marine Q 1000, G200 Series, K00383, FLARE NUT TXV REPLACEMENT (Z100) 7625563, E-1100, IB-0620.
Recommended Documentation:
Text Version of Manitowoc K00156 Ice Maker Manual (Summary of Contents)
(Ocr-Read of Document's Main Page, UPD: 02 October 2023)
K00156/157 ADAPTER KIT
Installation Instructions
1. Use the K00156 to install a Q-0200, Q-0450, Q-0600, Q-0800, Q-1000, and 30" S-series ice machines on a
Manitowoc C-950 bin.
Use the K00157 to install a Q-0200, Q-0450, Q-0600, Q-0800, Q-1000, and 30" S-series ice machines on a
Manitowoc C-970 bin.
2. Installation (the bin must be level before starting):
A. Remove the existing foam tape and ice deflector from bin.
B. For the K00156 kit, slide the support brackets onto the deflectors in the kit. For the K00157 kit, use the deflector
from the bin. Locate, as shown on the drawing below. Secure the deflector(s) to the bin with the screws removed
earlier.
C. Apply approximately 10 1/2” (26.7 cm.) of foam tape to the bottom front edge of the adapters between the bin and
the adapters.
D. Place the adapters on the bin, as shown.
E. Using the adapters as templates, drill four 5/32” (4 mm.) holes, .500” (12.7 mm.) deep maximum, in bin.
Warning: Do not drill through interior liner. Attach with the screws provided.
F. Apply foam tape to the edge of the adapters, as shown, and on the front and rear of the bin between the adapters.
Note: We recommend using RTV at intersections and along front inside edge of foam tape to prevent water
tracking. Use double tape thickness with S-series ice machines.
3. Refer to ice machine installation manual for ice machine installation procedures.
Manitowoc Ice, Inc.
2110 South 26
th
Street, P.O. Box 1720, Manitowoc, WI 54221-1720 USA
Telephone 920-682-0161, Fax - Sales: 920-683-7589, Service/Parts: 920-683-7585, Other: 920-683-7879 8011633
Web Site - www.manitowocice.com Rev. 05/12/04
Q-Model Ice
Machine Bac
k
LH Adapter
Screws from Kit
(TYP)
RH Adapter
12 1/2”
6 3/16”
6 3/4”
Double Thickness of
Tape with 30" S-series
Ice Machines
Recommended:
H50 Crosswalk Sl Treadmill, CAP AT91CAP7X-DK, DA1855A, 8/8 Base SAN series
CHE-12RC, F-1001MAF, MANITOWOC Indigo NXT, CD-200-VB, Prodigy Eclipse 1400, PROFI 48870
-
Manitowoc Ice PO Box 1720 Manitowoc, WI 54221-1720 T 920-682-0161 www.manitowocice.com 1 Instructions for upgrading Firmware for Indigo NXT Ice Machines Step 1: You must use a formatted 32 GB or smaller Flash Drive. This procedure can be downloaded from the Manitowoc Ice web ...
Model & Doc Type: MANITOWOC Indigo NXT 4
-
IMPORTANT:TO THE INSTALLER.It is the responsibility ofthe Installer to ensure thatthe water supply to thedispensing equipment isprovided with protectionagainst backflow by an airgap as defined inANSI/ASME A112.1.2-1979;or an approved vacuumbreaker or other suchmethod as proved effectiveby te ...
Model & Doc Type: Enduro 200 20
-
MODULAR ICE MAKERMACHINE A GLACE MODULAIREEISBEREITER FÜR SEPARATEN VORRATSBEHÄLTERIJSMACHINE MET LOSSE OPSLAGBUNKERMAQUINA DE CUBITOS MODULARFABBRICATORE MODULARE DI GHIACCIO89/33673/23INSTALLATION MANUALNOTICE D’INSTALLATIONINSTALLATIONSANLEITUNGINSTALLATIE VOORSCHRIFTMANUAL DE INST ...
Model & Doc Type: FM-1000ASFE3 37
-
Introduction:This manual covers the assembly, installation, startup, operation and maintenance of the 1400, 1800and 2000 remote low side cuber systems.Keep this manual for future reference.Prodigy Eclipseä 1400,1800, 2000April 2006Page 1Table of ContentsConfiguration············ ...
Model & Doc Type: Prodigy Eclipse 1400 46
Operating Impressions, Questions and Answers:
