Lode OEM Service Manual

15, Service manual OEM treadmill V2.03 15 2.6 Drive and reverse rollers 1/8/11 Item no. Quantity per assy Part Number Description 1 2 939018 SPANNER SUPPORT 2 1 939410 REVERSE ROLLER 3 1 827618 SCREW, SOCKET CAP M8 X 50 MM 4 1 932983 BELT, MULTI-V 5 4 816416 SCREW, SOCKET CAP M6 X 40 MM 6 2 932123 CLAMP, AXLE 7 1 939400…

5, Lode OEM Service manual OEM treadmill V2.03 Tabel of contents 1 TECHNICAL SPECIFICATIONS ............................................................................................................ 6 1.1 T ECHNICAL SPECIFICATIONS OEM TREADMILL 939900 ............................................................................ 7 2 ASSEMBLIES .......................................................................…

3, Lode OEM Service manual OEM treadmill V2.03 List of Symbols used On/Off switch External Input External Output Type B Electrical Safety Separate collection of electric and electronic equipment Copyright Lode BV, February 2012, all rights reserved. Manufacturer information: Lode BV Zernikepark 16 NL-9747 AN Groningen, The Netherlands ℡ : +31 50 571 28 11  : +31 50 57167 46 @ : [email protected] : www.lode.nl …

64, Lode OEM Service manual OEM treadmill V2.03 64 14. To access the service menu enter the code “945900” 15. The following options can be selected, with the module overview the actual software can be shown. 16. Select update module software …

60, Lode OEM Service manual OEM treadmill V2.03 60 6.6 Motor belt tension The tension of the motor belt can be checked by pulling the belt up and down in the middle between both pulleys. The full stroke must be about 10 mm. To change the tension of the belt remove the locking nut on the spanner socket screw of the motor belt. Turning the adjustment nut on the spanner socket screw will tilt the motor upwards (increase tension), or downwards (decrease tension…

36, Lode OEM Service manual OEM treadmill V2.03 36 fig.19 fig.20 fig.21 fig.22 fig.23 fig.24 …

32, Service manual OEM treadmill V2.03 32 3.6 Replacement instruction belt & deck Required tools • Allen key #3,#4,#5,#6 • Slotted screw driver #2 • Philips screw driver #2 • Ring spanner #10 Instruction 1. Remove the cover of the motor compartment as described in the instruction “removal cover of the motor compartment. 2. Remove the cosmetic covers at the (figure 2) 3. Remove the pin plug out of …

61, Lode OEM Service manual OEM treadmill V2.03 61 6.7 Inclination system The shaft of the inclination system should be kept clean and do not have to be lubricated as the motor is closed. By opening the motor housing the warranty will decline. …

7, Service manual OEM treadmill V2.03 7 1.1 Technical specifications OEM treadmill 939900 LODE TREADMILL OEM Treadmill 939900 SPEED RANGE - km/h 0,5 – 20 km/h (steps 0,1 km/h) - mph 0.3 – 12 mph HEIGHT ADJUSTMENT FRONT SIDE 0 – 25% WALKING SURFACE 50 x 150 cm MAXIMUM PATIENT WEIGHT 160 kg POWER REQUIREMENTS 230 VAC, 50-60 Hz 115 VAC, 50-60 Hz. (Between two Phases) …

39, Service manual OEM treadmill V2.03 39 3.8 Terminal application menu Terminal Application The protocol description, which follows, provides you with the information you need to connect to the Communication Interface Module (CIM) figure 1 to an external computer with suitable software and run commands from the terminal prompt. The default RS232 communication port settings as used in the CIM are: RS232 default communica…

40, Service manual OEM treadmill V2.03 40 After entering the Terminal Application on the CIM, a menu appears on-screen. For selecting the default communication protocol used with a PC, press “1”. To return to the first selections screen, press “backspace”. There are four protocols that can be used to communicate with the Treadmill; • Lode Treadmill • Trackmaster • Woodway • Coscom ( HP Cosmos) After selecting the desired protocol, the interface to which the …

59, Service manual OEM treadmill V2.03 59 6.5 Walking belt alignment When the treadmill is placed on a floor that is not flat, it is possible that the belt needs to be aligned. This may only be done by an authorized user. The following procedure must be followed: 7. Remove the caps (figure 1, A) 8. Adjust the speed of the treadmill to 5 km/h. 9. If the belt runs towards the left side, as viewed from the rear of the…

8, Service manual OEM treadmill V2.03 8 LODE TREADMILL OEM Treadmill 939900 ENTRANCE PLATE optional ANTI SLIP STRIPS standard SIDE HANDRAILS FIXED (HEIGHT 850 MM) optional SIDE HANDRAILS ADJUSTABLE optional - height: 791 – 954 mm - width : 440 – 975 mm PEDIATRIC FRONT HANDRAIL optional PEDIATRIC SIDE HANDRAIL optional - height: 600 - 763 mm - width : 440 – 975 mm ARM SUPPORT optional WIDER / LONGER RUNNING SURFACE optional …

33, Lode OEM Service manual OEM treadmill V2.03 33 fig.1 fig.2 fig. 3 fig.4 fig.5 fig.6 …

25, Service manual OEM treadmill V2.03 25 3.2 Removal of the cover motor compartment Required tools: • Allen key #3 Instruction 1. Use the Allen key #3 to remove the screws in the housing of the motor compartment of the treadmill (figure 1&2) 2. Lift the housing from the back side and gently pull it up (figure 3& 4) fig.1 fig. 2 fig.3 fig.4 …

66, Service manual OEM treadmill V2.03 66 21. The complete upload will take a few minutes depending on the size of the file 22. When done, the message Module Flash successful, restart device will be shown. …

57, Lode OEM Service manual OEM treadmill V2.03 57 6.3 Grade calibration Calibration procedure grade Measure the inclination of the treadmill by using a angle measurement tool. The accuracy of the inclination should be within 3% The grade of the treadmill is absolute the inclination sensor is calibrated in the factory and cannot be readjusted. In case during calibrations of the grade the grade would not within specifications this could have the following causes. 1. An offset in the grade could be caused by a flo…

51, Service manual OEM treadmill V2.03 51 5.1 Messages During operation of the treadmill a full diagnostic analysis is running continuously, in case an error occurs the user needs to be warned and an audio signals will sound. LED’s on the Treadmill Control Module will blink to indicated what might be the cause of the problem. The order in which they blink can be compared with table 1 in this chapter. This chapter describes the explanation of the error codes. When the emergency circuit is activated…

55, Service manual OEM treadmill V2.03 55 6.1 General Maintenance Visual inspection: • Housing • Display • Cables, sockets e.g.line voltage entrance • User Interface, e.g. a keyboard Mechanical check-up • Technical cleaning of mechanical parts • Freewheel assembly • Braking assembly, bearings • Saddle assembly/handle bar assembly Inspection electronics • Primary and secundary electronic circuits • Optio…

11, Service manual OEM treadmill V2.03 11 2.2 Handrail assy 939020 Item Number Quantity per assy Partnumber Description 1 2 939015 VERTICAL ARM HANDRAIL, LEFT 2 1 939016 VERTICAL ARM HANDRAIL, RIGHT 3 1 939017 VERTICAL ARM HANDRAIL WITH CABLE, RIGHT 4 1 939110 UPPER HANDRAIL ASSY …

26, Service manual OEM treadmill V2.03 26 3.3 Replacement Communication interface module (CIM) Required tools: • Philips screw driver # 1 Instruction 1. Remove the cover of the motor compartment as described in the instruction “removal cover of the motor compartment. 2. Remove the flat cable from the main board (figure 1) 3. Remove the flat cable from the communication interface module …

65, Service manual OEM treadmill V2.03 65 17. Select the module number that you would like to flash the software from 18. Select Transfer in the terminal program 19. Choose XMODEM and Send 20. Select the XXXXX.CDE file that you would like to send …

53, Lode OEM Service manual OEM treadmill V2.03 53 Figure 2 …

29, Service manual OEM treadmill V2.03 29 3.5 Replacement instruction main board 945701 Required tools: • Philips screw driver #2 Instruction 1. Remove the cover of the motor compartment as described in the instruction “removal cover of the motor compartment. 2. Remove the grade motor as described in the replacement instructions of the grade motor. 3. Remove the cables from the main board (figure 1,2,3,4,5,6,7&8) 4. To remove the cables from the power entree/ci…

43, Service manual OEM treadmill V2.03 43 9. The information on shown in Hyperterminal should be as above 10. When SPACE is pressed the menu to select the communication protocol will appear …

58, Service manual OEM treadmill V2.03 58 6.4 Walking belt tension In case the belt tension needs to be readjusted, e.g. after replacement of the belt you must follow the procedure below: 1. Remove the caps (figure 3, A) 2. Make sure there is no tension on the belt, you should be able to lift the belt at least 2 cm without feeling tension. 3. Place two markers on the belt exactly 1000 mm from each other (figure 1) 4. Now st…