Scantech Sirius S-7030 Operation & User’s Manual

Operation & User’s Manual for Scantech Sirius S-7030 Barcode Reader (40 pages)

Specifications:

710/710169-sirius_s7030.pdf file (23 May 2024)
  • Manufacturer: Scantech
  • Category of Device: Barcode Reader
  • Document: Sirius S-7030, File Type: PDF Operation & User’s Manual
  • Updated: 23-05-2024
  • Count of Pages: 40
Download Sirius S-7030 Manual (40 pages)

Scantech Sirius S-7030: Read PDF Manual Online

Data: UPD 23rd May 2024

Scantech Sirius S-7030 Barcode Reader PDF Operation & User’s Manual (Updated: Thursday 23rd of May 2024 07:38:18 PM)

Rating: 4.2 (rated by 49 users)

Compatible devices: LIBRA L-7050, V-1020, Vega V-1010, MICA M-9030, LIBRA L-7080i, DC-100, V-1020BT, Pollux P-4010.

Recommended Documentation:

Scantech Sirius S-7030: Text of Operation & User’s Manual

(Ocr-Read Version Summary of Contents, UPD: 23 May 2024)
  • U S E R ’ S M A N U A L

    Scantech Sirius S-7030

    Bar Code Laser Scanner

  • User’s Manual

    Scantech Sirius S-7030

  • Copyright © 2007, Scantech-ID BV.

    This manual is copyrighted, with all rights reserved. Under the copyright laws, this manual may not, in

    whole or in part, be copied, photocopied, reproduced, translated or converted to any electronic medium or

    machine readable form without prior written consent of Scantech-ID BV.

    Limited Warranty

    Under all circumstances this manual should be read attentively, before installing and/or using the pro-duct.

    In no event shall Scantech-ID BV be liable for any direct, indirect, special, consequential or incidental

    damages arising out of the use or inability to use this documentation or product, even if advised of the

    possibility of such damages. In particular, Scantech-ID BV shall not be liable for any hardware, software, or

    data that is stored or used with the product, including the cost of repairing, replacing or recovering the

    above. Scantech-ID BV reserves the right to change parts of the device at any time without preceding or

    direct announcement to the client.

    Scantech-ID BV reserves the right to revise this manual, and to make changes in the contents without

    obligation to notify any person or entity of the revision or change. A serial number appears on the product.

    Make sure that this official registration number has not been removed. It should be used whenever

    servicing by Scantech-ID BV or an authorized Scantech dealer is necessary.

    Important

    This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

    EN55022, and with the limits for a class A digital device, pursuant to part 15 of the FCC rules. These limits

    are designed to provide reasonable protection against harmful interference when the equipment is operated

    in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy

    and, if not installed and used in accordance with the user‟s manual, may cause harmful interference to radio

    communications. Operation of the equipment in a residential area is likely to cause harmful interference in

    which case the user will be required to correct the interference at his own expense. Any unauthorized

    changes or modifications to this equipment could void the user‟s authority to operate this equipment.

    For CE-countries:

    - The Sirius is in conformity with the CE standards. Please note that a Scantech CE-marked power supply

    unit should be used to conform to these standards.

    For USA & Canada

    - To be used with UL listed and CSA certified computers/POS systems.

    - A utiliser avec des ordinateurs/systèmes POS registrés UL/certifiés CSA.

    - This scanner should only be powered by a UL listed or CUL Certified Power Supply having limited power

    source of Class 2 outputs, rated +5.2 Vdc / minimum 0,64 A, minimum 40 °C or the scanner should be

    directly powered by a UL listed and CSA certified computer/POS system, having limited power source

    of Class 2 outputs, rated 5.2 / minimum 0,55 A, minimum 40 °C.

    Radio and television interference

    Operation of this equipment in a residential area can cause interference with radio or television reception.

    This can be determined by turning the equipment off and on. The user is encouraged to try to correct the

    interference by one or more of the following measures:

     Re-orientate the receiving antenna

     Relocate the devices with respect to the receiver

     Move the device away from the receiver

     Plug the device into a different outlet in order to have the device and receiver on

    different branch circuits

    If necessary, the user should consult the manufacturer, an authorized Scantech dealer or experienced

    radio/television technician for additional suggestions. The booklet "How to Identify and Resolve Radio -TV

    Interference Problems", prepared by the Federal Communications Commission, can be of help. It can be

    obtained from the U.S. Government Printing Office, Washington, DC 20402, Stock No. 004000003454.

    P/N A052001 January 2007

  • Table of contents

    Preface ...................................................................................................i

    Chapter 1 The Sirius S-7030 ....................................................................... 3

    1.1 Unpacking the Sirius S-7030.................................................. 4

    1.2 Scanner labelling .................................................................. 6

    1.3 Laser safety ......................................................................... 7

    Chapter 2 Installation.................................................................................. 9

    2.1 Connecting the scanner....................................................... 10

    2.2 Powering the Sirius Scanner. ............................................... 11

    2.3 Mounting the scanner plus flexible stand ............................... 13

    2.4 Controlling the scanner from the POS system ....................... 15

    2.5 Standard available interface cables ...................................... 15

    2.6 Interface Selection .............................................................. 18

    Chapter 3 Using the Sirius S-7030............................................................. 19

    3.1 Orientation ......................................................................... 20

    3.2 Scanning bar codes with the Sirius S-7030 ........................... 22

    3.3 Single line scanning ............................................................ 23

    3.4 Maintaining the scanner…………………………………… ...... 24

    Appendices ............................................................................................... 25

    A Connector types and pin definitions ...................................... 26

    B Technical specifications....................................................... 28

    C Troubleshooting.................................................................. 30

  • Preface

    The Scantech Sirius S-7030 scanner combines the demand for table mounted-

    and hand held scanning. The ergonomic design ensures effortless handling and

    the sympathetic good looks will automatically enhance any working environment.

    It is based on proven Scantech-ID technology which forms the basis of all our

    omni-directional scanners. Bar code labels are read by presenting the labels

    towards the scanner. Alternatively you can take the scanner in your hand and

    present it towards the bar code. Using both functionality‟s results in maximum

    scanning capabilities, using only a minimum footprint on the counter desk.

    One button operates the Sleepmode (wake-up) and the „single-line‟ feature, such

    you can easily target, similar to an ordinary, non-omni directional handgun. This

    is convenient if you need to scan just one out of many labels close to each

    other.

    The Sirius S-7030 reads all popular bar code symbologies. For the reading of

    damaged and out-of-spec codes, the latest ASIC technology and STAR code

    reconstruction software has been integrated.

    The Sirius S-7030 is equipped with triple interface for integration in nearly every

    environment. The interface (RS-232, Key Board Wedge or USB) is selected by

    the cable connected. USB plus power is supported as well. The low power

    consumption makes the Sirius multi-connectable. The Sirius is available in three

    different colour schemes and standard supplied with an EAS antenna and its

    very flexible stand for turning 360 and tilting ± 25 degrees.

    This manual contains three chapters and three appendices. The first chapter

    describes the Sirius and its general features. The description for installation

    can be found in the second chapter. Precisely follow the instructions for the

    installation of the scanner. The scanners‟ settings can be changed with

    the bar code labels from the Configuration Guide that came with the unit.

    Chapter three describes the daily use of the scanner.

    Appendix A gives the pin definition for the connected cable. The pin definition

    may be required when you want to make a new or special cable for

    communication with the POS/computer. Technical specifications of the Sirius

    S-7030 can be found in Appendix B. Refer to Appendix C for troubleshooting

    if the scanner is not working properly.

  • Chapter 1 The Sirius S-7030

  • 4

    1.1 UNPACKING THE SIRIUS S-7030

    The Sirius S-7030

    Remove the scanner and its accessories from the box and packing material.

    Refer to the packing list to make sure you have received all the items ordered.

    Visually inspect the scanner and accessories for any evidence of physical

    damage. Check with the information of chapter 2.5 that you have got the right

    interface cable. Immediately contact your supplier if anything appears to be

    damaged, or if the supported interface cable does not correspond with the host

    system interface.

    Optional

    ATTENTION

    Details may differ from the illustration above, however in

    functionality it should be identical.

    The power supply is not always included.

  • The Sirius S-7030

    The specific parts of the Sirius S-7030 are:

    5

    Sleep mode /

    Single Line button

    LED

    Good read buzzer

    Flexible scanner

    stand

    End cover

    Interface cable

    User’s manual

    Configuration guide

    - To “wake-up” the scanner after being in “Sleep

    Mode”. The time-out (default 30 minutes) is

    programmable using the labels from the

    Configuration Guide. During Sleep Mode, the

    LED is intermittently flashing red.

    - To enable the “Single Line” scan option, when

    you need to scan only one out of many

    barcodes. See Chapter 3.3.

    - A red LED indicates that the scanner is ready to

    read a bar code.

    A green LED indicates a good read.

    - The buzzer is heard whenever a bar code has

    been read correctly.

    The frequency and volume can be adjusted.

    - The rotary and flexible stand allows you to

    direct the scan pattern in a way that is optimal

    for your application (a mounting kit with screws

    and tapes is included). The scanner can be

    lifted out for manual scanning.

    - This part serves to cover the connector area

    of the scanner.

    - One of various types of cable to connect to

    your host computer / POS system.

    See Chapter 2.5 for more details.

    - This manual in print.

    - Booklet containing barcodes to configure

    the scanner

    Optional parts & accessories:

    Power supply

    - Required if your scanner is not directly powered

    by the host system (optional).

  • 6

    1.2 SCANNER LABELLING

    The Sirius S-7030

    The type-label is present on the bottom side of the Sirius S-7030 as indicated in

    the illustration below. Another label is visible through the scanner window. All

    labels are attached by the manufacturer and should not be removed.

    The scanner‟s serial number and type number are found underneath the scanner

    as depicted in the figure above. This official registration number is strictly

    related to the device. The supplier may ask for these numbers when the scanner

    needs servicing.

  • The Sirius S-7030

    1.3 LASER SAFETY

    German:

    7

    Der Strichcode-Scanner S-7030 entspricht den Sicherheitsvorschriften nach IEC 825-1 (1993) für ein

    Laserprodukt der Klasse I. Er entspricht auch U.S. 21CFR1040, anwendbar auf ein Laserprodukt der

    Klasse IIa. Vermeiden Sie langzeitiges Hineinblicken in direktes Laserlicht.

    Dutch:

    De S-7030 scanner voldoet aan de veiligheidsnormen IEC 825-1 (1993) voor een Klasse I

    laserproduct. Tevens voldoet de scanner aan U.S. 21CFR1040, van toepassing op een Klasse IIa

    laserproduct. Vermijd langdurig kijken in direct laserlicht.

    French:

    Le scanner S-7030 est conforme aux normes de sécurité IEC 825-1 (1993) s‟appliquant à un produit

    laser de la classe I. Il est également conforme à la U.S. 21CFR1040 telle qu‟elle s‟applique à un

    produit laser de la classe IIa. Eviter de rester exposé longtemps à la lumière directe du laser.

    Danish:

    S-7030 skanneren er i overensstemmelse med sikkerhedsstandarden IEC 825-1 (1993) for

    laserprodukter i klasse I. Den er også i overensstemmelse med U.S. 21CFR1040, der gæ lder for

    laserprodukter i klasse IIa. Undgå at se direkte på laserlys i læ ngere perioder.

    Finnish:

    S-7030-skanneri täyttää luokan I lasertuotteelle IEC 825-1:ssä (1993) asetetut turvavaatimukset. Se

    täyttää myös U.S. 21CFR1040:ssa asetetut vaatimukset siltä osin kuin ne koskevat luokan IIa

    lasertuotetta. Vältä pitkäaikaista suoraan laservaloon katsomista.

    Swedish:

    Avsökaren S-7030 uppfyller säkerhetsnormen IEC 825-1 (1993) för laserprodukter av klass 1. Den

    uppfyller dessutom U.S. 21CFR1040 som gäller för laserprodukter av klass IIa. Undvik att titta i

    direkt laserljus under längre perioder.

    Norwegian:

    S-7030 skanneren er i samsvar med sikkerhetsstandarden IEC 825-1 (1993) for laserprodukter i

    klasse I. Den er også i samvar med U.S. 21CFR1040 for laserprodukter i klasse IIa. Unngå å se

    langvarig på direkte laserlys.

    Italian:

    Lo scanner S-7030 è conforme alle norme di sicurezza IEC 825-1 (1993) relative ad un prodotto

    laser di Classe 1. È inoltre conforme alla norma U.S. 21CFR1040 relativa ad un prodotto laser di

    Classe IIa. Evitare l'esposizione prolungata all'emissione diretta di luce laser.

    Portuguese:

    O scanner S-7030 está conforme as normas de segurança IEC 825-1 (1993) para a Classe 1 dos

    produtos laser. Também está conforme a norma U.S. 21CFR1040 aplicada nos produtos laser da

    Classe IIa. Evite expor os olhos directa e prolongadamente aos raios laser.

  • 8

    Spanish:

    The Sirius S-7030

    El scanner S-7030 reune las normas de seguridad IEC 825-1 (1993) para un producto laser de

    Clase 1. Y también reune las normas U.S. 21CFR1040 que se aplican a un producto laser de Clase

    IIa. Se debe evitar mirar muy fijo en luz lasérica directa.

    English:

    The S-7030 scanner complies with safety standard IEC 825-1 (1993) for a Class I laser product. It

    also complies with U.S. 21CFR1040 as applicable to a Class IIa laser product. Avoid long term

    viewing of direct laser light.

    Optical:

    The use of optical instruments with this product will increase eye hazard. Optical instruments include

    binoculars, microscopes and magnifying glasses but do not include eye glasses worn by the user.

    Radiant Energy:

    The S-7030 uses a low-power laser diode operating at 630…670 nm in an opto-mechanical scanner

    resulting in less than 0.6 mW peak output power. Laser light observed at 13 cm (5.1 in.) above the

    window through a 7 mm (0.28 in.) aperture and averaged over 1000 seconds is less than 3.9 µW

    per CDRH Class IIa specification. Do not attempt to remove the protective housing of the scanner,

    as unscanned laser light with a peak output up to 0.8 mW could be accessible inside.

    Laser Light Viewer:

    The scanner window is the only aperture through which laser light may be observed on this product.

    A failure of the scanner motor, while the laser diode continues to emit a laser beam, may cause

    emission levels to exceed those for safe operation. The scanner has safeguards to prevent this

    occurrence. If, however, a stationary laser beam is emitted, the failing scanner should be

    disconnected from its power source immediately.

    Adjustments:

    Do not attempt any adjustments to or alteration of this product. Do not remove the scanner‟s

    protective housing. There are no user-serviceable parts inside.

    DANGER!

    Use of controls or adjustments or performance of procedures

    other than those specified herein may result in hazardous laser

    light exposure.

  • Chapter 2 Installation

  • 10

    2.1 CONNECTING THE SCANNER

    Installation

    Before you connect any cable to the scanner, decide whether you will guide it

    backward as a tail or downward, through the foot and counter surface!

    1. Remove the end cover.

    Firmly press the end cover as indicated below and carefully slide the cover

    approx. ¾ cm. downward (referring to normal operating position).

    Now you can lift off the cover.

    (If you have an older type of cover, press the two little clips on the bottom

    and carefully shift the end cover downward and take it away. („Downward‟ is

    referring to the normal lower side of the scanner, if positioned in operating

    position.))

    2. Make sure the power has been turned off and connect the interface cable

    to the 10-pin RJ-48 connector of the scanner as indicated below:

    3. In case you use an EAS cable do not forget to mount the EAS connector

    on the small white port under the data port.

  • Installation 11

    4. Be sure you make a loop in the cable, which will fit under the end-cover,

    as this is an essential part of the strain relief (see right picture above).

    5. Guide the cable through the exit slit and carefully mount the end cover.

    6. (If you have an older type of cover: lock the two little clips by shifting them

    toward the front of the scanner until you hear it click.

    The Sirius S-7030 is standard equipped with the following interfaces:

    RS-232

    Key Board Wedge (KBW)

    USB and USB plus power.

    The scanner also provides:

    EAS connection

    2.2 POWERING THE SIRIUS SCANNER.

    The Sirius is designed so that you only need one single and simple cable for

    both data and power using “Direct Power” (or “Power Of Terminal”).

    This requires that your PC/POS system is providing sufficient power on its

    data port (RS-232, USB or KBW). See Appendix B for details.

    All applicable Sirius interface cables have a power injector to connect an

    optional external PSU in the case the POS system does not supply (sufficient)

    DC power for the scanner. See next page for illustration.

    A standard PC USB port will supply sufficient power for the scanner to function

    without any problems. The Sirius can also be connected to the „USB plus power‟

    ports (the green connector).

    If you use Key Board Wedge interface, the PC/POS system usually supplies

    sufficient power. Some PC/POS systems may have problems supplying the

    required power via the Key Board connector. In this case you can easily add

    an external power supply and connect it via the available power injector in the

    KBW cable.

  • 12

    ATTENTION

    Installation

    Though most cables do have a power injector in the cable, this

    does not automatically mean that you must use a power supply.

    For safety reasons an automatic switch will disconnect the

    power provided by the PC/POS system, as soon as a separate

    power adapter is connected to the power injector.

  • Installation

    2.3 MOUNTING THE SCANNER PLUS FLEXIBLE

    STAND

    To install the scanner on the flexible scanner stand, lead the cable either

    13

    backward via the slit in the rear-side of the stand, or guide it vertically through

    the stand to be connected to the scanner. Furthermore the stand should be

    fastened to the counter top. You than can easily put the scanner in the stand.

    To mount the stand you are advised to precisely follow the next steps:

    1. Gently pull the bottom disk out of the stand.

    2. Place the bottom plate on the counter and mark the places for the

    mounting holes on the counter top and mark the hole to lead the cables

    through.

    3. Drill the mounting holes and the lead-through hole.

    ATTENTION

    If you prefer not to drill in your counter, you can mount the stand

    using the provided double-sided tape and have the cables leave the

    foot at the rear, just above the circular basis.

    4. Fix the bottom plate on the counter top using the screws or tape from the

    mounting kit.

  • 14

    5. Optional:

    Lead the cables from the bottom upwards

    through the hole in the counter, through the

    bottom plate and through the scanner stand.

    Click the stand on the bottom plate.

    Installation

    6. Connect the cable(s) to the scanner. Refer to chapter 2.1 for the correct

    method.

    7. Place the scanner onto the flexible stand and rotate the scanner into the

    desired position.

    8. Connect the data cable to the host.

    See note in Chapter 2.2

    9. If applicable, connect the power supply plug to the power injector. Than

    connect the IEC power cord to the AC/DC power supply and plug the AC

    power cord into an AC power outlet.

    10. Place the scanner in the desired angle (see Chapter 3.1).

    11. Switch on the host system

    ATTENTION

    Once the scanner is installed, you can start scanning bar code

    labels. If you want to change the default settings of the scanner,

    proceed to the Configuration Guide which came with the scanner.

  • Installation 15

    2.4 CONTROLLING THE SCANNER FROM THE POS SYSTEM

    The Sirius S-7030 can be controlled from the POS system via the RS-232

    interface or USB/COM Port Emulation. Control is achieved by transmitting the

    following single byte commands to the scanner. In the Scantech default setting

    the following commands are available (more details available upon request):

    ASCII code

    05 Hex

    OE Hex

    OF Hex

    12 Hex

    14 Hex

    Function

    Power-up re-initialization

    Enable (cancels disable)

    Disables the scanner

    Puts scanner into Sleep

    Wake (cancels sleep)

    Byte is also called:

    ENQ or <Ctrl-E>

    Shift Out or <Ctrl-N>

    Shift In or <Ctrl-O>

    DC2 or <Ctrl-R>

    DC4 or <Ctrl-T>

    When the scanner is disabled, the motor of the scanner will stay on,

    until the scanner goes into sleep mode.

    2.5 STANDARD AVAILABLE INTERFACE CABLES

    On the next pages you see the standard available interface cables with some

    additional information.

    Note that the power injector may be used to insert the DC power from the

    optional external power supply. However if your POS/PC system provides

    sufficient power directly via the data port, no external power supply is required.

    A safety measure prevents from damage in case you connect a power supply

    where it is not required (by disconnecting the power from the POS/PC system).

    If you are using the Sirius with USB interface, no external power supply is

    required at all.

  • 16

    A201901 Cable Key Board Wedge, mini-DIN:

    Installation

    DP+EP *

    A201902 Cable RS-232 Wincor Beetle POS, Sub-D 9-pin Male DP (+EP) *

    A201903 Cable RS-232 PC-POS, Sub-D 9-pin Female DP (+EP) *

    A201904 Cable RS-232 Fujitsu-ICL TeamPOS, Sub-D 9-pin Female DP (+EP) *

    A201906 Cable RS-232 IBM 4614 Sure One, Sub-D 15-pin Male DP (+EP) *

  • Installation

    A201913 Cable USB standard, USB-connector 4-pin DP *

    Note: The Sirius-USB must be directly connected to the

    PC-USB port and not through an (un-powered) USB hub.

    A201908 Cable USB plus power Green 8-pin connector DP *

    A201508 Gender Changer / KBW-PC DIN adapter

    * DP means Direct Power (Power Of Terminal)

    EP means External Power through the optional PSU.

    17

  • 18

    2.6 INTERFACE SELECTION

    Installation

    The Sirius S-7030 is equipped with triple interface for integration in nearly every

    environment: RS-232, Key Board Wedge, USB or USB plus power. The interface

    is selected by the cable connected. On power up the scanner senses the type of

    interface used and switches to the appropriate protocol. However some

    variations are possible.

    From the Scantech factory, the Sirius is in RS-232 Interface Mode.

    ATTENTION

    Changing from interface is very simply done by following

    these steps:

    1. Connect the applicable interface cable to the Sirius

    2. Power-up the scanner

    3. Initialize the communication parameters by scanning

    programming bar codes 1.1 and 1.3 from the Configuration

    Guide.

    This procedure is required once-only.

    In KBW-mode the scanner defaults to the International Keyboard lay-out

    (ALT-method) for communication in the most versatile way. Settings may be

    changed to some national keyboards if required, using the Configuration Guide

    Chapter 3.4.

    In RS-232 mode, the default communication parameters are 9600,N,8,2. Using

    the Scantech Configuration Guide Chapter 3.1, you may select one of the

    various presets, or set each parameter by hand.

    In USB-mode the scanner defaults to Keyboard Emulation Mode (compare the

    KBW cable). The Sirius transmits the data in International Keyboard lay-out (ALT-

    method) for communication in the most versatile way. Settings may be changed

    to national keyboards if required, using the Configuration Guide Chapter 3.4.

    Other USB communication selections (are:

    - USB IBM fixed POS scanner

    - USB IBM handheld scanner emulation

    - USB COM Port emulation (Scantech supplies a driver for this)

    See Configuration Guide Chapter 3.5

    Note: The Sirius-USB must be directly connected to the PC-USB port and not

    through an (un-powered) USB hub.

  • Chapter 3 Using the Sirius S-7030

  • 20

    3.1 ORIENTATION

    Using the Sirius S-7030

    See the picture below to get acquainted with the various parts of the scanner.

    Red LED: ‟Ready‟

    Green LED: „Good Read‟

    Button;

    „Wake-Up‟ or

    „Single-Line‟

    Rubber Grips

    Data/Power Cable

    Stand, adjustable

  • Using the Sirius S-7030

    Adjust the orientation of the scanner the scanner by rocking it carefully while

    mounted in the stand and by rotating the stand on its floor surface.

    21

    Position it such that the beam pattern is projected optimally onto the products

    you present for scanning.

    To scan barcodes on large or difficult to reach objects, you may lift the scanner

    from its stand and use the scanner as a hand scanner. In the standard

    configuration, the scanner is scanning continuously, so you do not need to

    „trigger‟ like with a traditional hand scanner.

    „Rocking‟ the scanner

    „Foot-rotation‟

  • 22 Using the Sirius S-7030

    3.2 SCANNING BAR CODES WITH THE SIRIUS S-7030

    The Sirius S-7030 is an omni-directional presentation scanner featuring a 5

    directional scan field with a 20 lines scan pattern with 1350 scans/sec.

    Bar code labels can easily be read by presenting them to the scanner.

    The scanner can be used hands-free as well as hand-held, e.g.

    Hands free scanning by presenting the item to the scanner

    Handheld scanning by taking the scanner out of the stand and aiming it to the

    barcode label on the products.

    ATTENTION

    Since the Sirius is a presentation scanner, best results are

    obtained if the barcode is moved towards the scanner (or move

    the scanner towards the barcode).

    The scanner's scan volume is illustrated in the figure below. The optimal reading

    zone lies between 2 and 15 cm from the scanner window, but bar codes may be

    read up to 20 cm from the scanner window (EAN/UPC 100%).

    0 2 15 20 cm

  • Using the Sirius S-7030

    3.3 SINGLE LINE SCANNING

    The Sirius is provided with a “Single Line” option, which helps you selecting

    23

    specific codes when multiple bar codes are very close together. A typical case

    is when you need to scan just one code from a pick list

    full of bar codes.

    Instructions for Single Line scanning:

    1. Take the scanner in your hand and press the

    button.

    The scan pattern will change to a single line now.

    2. Aim the single line on the barcode to be scanned

    while holding the button pressed.

    3. Once the scan line is completely crossing the barcode, release the button.

    At this moment, the code is read, a beep sounds and the data is

    transmitted.

    The scan line will blink as a confirmation of good read and as a warning that

    the single line mode will stop unless you press the button again!

    4. If you press the button again during the blinking period, you can start

    scanning another barcode using single line.

    ATTENTION

    If you need to scan many barcodes sequentially, in Single Line

    mode, you can best press the button again directly after releasing

    it. In this way you reenter the Single Line mode immediately.

    This will protect you from the following risk:

    IMPORTANT

    If you release the button and keep the scanner aimed at a group of

    barcodes, the scanner will return to normal, omni-directional

    operation, as soon as the blinking period of the line stops.

    Barcodes in range of the omni-directional scan field will be read,

    even without pressing the button!

  • 24

    3.4 MAINTAINING THE SCANNER

    Using the Sirius S-7030

    The Sirius S-7030 scanner requires little maintenance. Only occasional cleaning

    of the scanner window is necessary to remove dirt or fingerprints. Cleaning can

    be performed during operation with a non-abrasive glass spray cleaner and a

    soft lint-free cloth.

  • Appendices

    A. Connector types and pin definitions

    B. Technical Specifications

    C. Troubleshooting

  • 26

    A

    CONNECTOR TYPES AND PIN DEFINITIONS

    Appendices

    There are three interfaces in the Sirius: RS-232, Key Board Wedge and USB

    (plus power). The various pin definitions (depending on the used type of

    interface) are given below. The connector type is RJ-48, 10 pins.

    IMPORTANT

    Various interface cables are available, depending on the kind of

    PC/POS system you use. See Chapter 2.5. Contact your supplier

    for availability. In case you need a special interface cable, you can

    use the information below.

    Pin definitions for multi interface.

    Connector: RJ-48, 10 pins.

    Multiple Interface

    RS-232

    KBW

    USB

    Pin Description Description Description

    Remark

    1

    2

    3

    4

    5

    6

    7

    8

    9

    10

    -

    CTS

    RxD

    TxD

    RTS

    Ground

    +5.2V

    D-Power

    -

    -

    -

    PC-Clock

    PC-Data

    KB-Data

    KB-Clock

    Ground

    +5.2 V

    D-Power

    IFID: connect

    to Pin 6

    -

    IFID

    -

    -

    IFID: connect

    to Pin 1

    -

    Ground

    +5.2 V

    D-Power

    D +

    D -

    IFID=InterFace ID

    IFID=InterFace ID

    Ground

    5.2Vdc DC input

    to power scanner *

    8-16Vdc DC input

    to power scanner *

    IFID=InterFace ID

    D + = USB data

    D - = USB data

    * The Sirius only requires one single DC input.

  • Appendices

    Pin definition EAS connector

    EAS

    Pin Description Direction

    27

    1

    2

    ( - )

    (+)

    -

    -

    The EAS connection is used to connect the internal deactivation antenna to an

    external EAS control unit.

  • 28

    B

    TECHNICAL SPECIFICATIONS

    Appendices

    Electrical

    Power supply voltage (optional) 100 – 240 V ac 50/60 Hz (adapter)

    DC input to scanner

    Interfaces

    Optical

    Light source

    Depth of field

    Scan pattern

    Scan rate

    Decoding

    Bar code types

    Physical

    Weight (scanner only)

    Weight of stand

    Dimensions without stand

    Dimensions with stand

    5.2 Vdc 260 mA or 8 – 16Vdc max 2VA

    RS-232, KBW and USB/USB plus power

    Visible laser diode (630 - 670 nm)

    Approx. 200 mm / 8 inches (EAN/UPC 100%)

    Max range approx. 300mm/12” (EAN/UPC 200%)

    5 directions scan field,

    20 lines scan pattern plus

    Single Line option

    1350 scans / second

    EAN/UPC/JAN + Add-on

    Code 128

    EAN 128

    Interleaved 2/5

    MSI/Plessey

    Code 93

    Code 39

    Code 39 full ASCII

    Code 32 (Italian Pharmacode)

    Codabar

    225 g

    110 g

    H x W x D : 122 x 86 x 62 mm

    : 4.80 x 3.39 x 2.44 inch

    H x W x D : 165 x 120 x 85 mm

    : 6.50 x 4.72 x 3.35 inch

  • Appendices

    Environmental

    Operating temperature 0° C ~ 40° C

    Humidity 20% ~ 95% RH (non-condensing)

    Safety

    Laser safety IEC 825-1 (1993) Class I, U.S. CDRH: 21CFR1040 Class II a

    Electrical safety EN 60950 second edition, IEC 950 (1991)

    UL1950 third edition, c-UL (according CSA22.2.950-M95)

    Flammability rate 94V-0

    EM Compatibility

    29

    EMC

    EN 61000-6-3 (2001) Generic emission standard, from which:

    EN 55001 (1998) Emission –class B

    EN 61000-6-2 (2001) Generic immunity standard, from which:

    EN 61000-4-2 (1995) Electrostatic Discharge (ESD) Immunity,

    EN 61000-4-3 (1996) Radiated Electro-Magnetic field immunity,

    ENV 50204 (1995) Digital radio telephones immunity,

    EN 6100-4-4 (1995) Electrical Fast Transient (EFT) Immunity,

    EN 61000-4-5 (1995) Surge transient immunity,

    EN 61000-4-6 (1996) Conducted RF disturbances Immunity

  • 30

    C

    TROUBLESHOOTING

    Appendices

    This section contains information on solving problems you may encounter when

    using the scanner. If troubles occur, take a moment to read the information in

    this section. However, before referring to the diagnostic tips make sure that the

    scanner is installed as described in Chapter 2 and that all cables are properly

    connected.

    Problem

    The scanner is on but a bar code cannot

    be read. The LED is red.

    The scanner is on, but the motor is not

    rotating. A bar code cannot be read.

    The LED is intermittently flashing red.

    The LED is alternating red/green

    The LED is alternating red/green and

    beeps are heard.

    The scanner does not accept more than

    two or three bar codes

    Diagnostic Tips

    The scanner window is dirty. Clean

    the scanner window as described in

    the Maintenance section.

    The presented bar code type is not

    enabled. Select the bar code type

    with the Configuration Guide.

    The scanner is disabled by the host.

    Refer to Section 2.4.

    The bar code type you presented to

    the scanner is not supported by the

    Sirius.

    The scanner is in sleep mode. Press

    the switch on top of the scanner to

    reactivate the scanner (or use the

    wake protocol. Refer to section 2.4).

    Mirror motor is defective and must

    be replaced (Authorized personnel

    only).

    Possible failure of the scanning

    safeguard circuit. Immediately

    disconnect the scanner from its

    power source. Contact your supplier.

    There is no proper handshaking with

    the host system. Switch the host

    system on and check connection and

    communication settings.

  • Appendices

    Problem

    Diagnostic Tips

    31

    Both the green and red LED are

    burning.

    The LED is blinking green+red.

    The LED remains green

    A bar code is read by the scanner but

    not accepted by the host system.

    The laser is not functioning. The laser

    is defective. Contact your supplier.

    The ambient temperature is too high.

    Make sure the scanner has enough

    air ventilation and is not placed in

    direct sunlight.

    The scanner is continuously seeing a

    bar code. Remove all bar code labels

    from the scan volume of the scanner

    and try again.

    The scanner cannot send the data to

    the host system. There is no proper

    handshaking between the scanner

    and the host. Scanner buffer is full.

    Make sure that all cables are

    connected and your host system is

    ready to receive data.

    The communication cable is not

    connected to the serial port of your

    host system. Refer to the manual of

    your host system to locate the serial

    port.

    The communication settings of the

    host and scanner do not match.

    Ensure that the setting value for both

    devices are the same. For proper

    adjustment values see the

    Configuration Guide.

    The communication cable does not

    suit your host system. Contact your

    supplier for the correct

    communication cable.

    The data format is not supported by

    the software running on the host

    system.

  • 32

    Problem

    Diagnostic Tips

    Appendices

    USB communication is not working

    Restart the scanner by temporarily

    disconnecting the scanner at the

    POS/PC side. This may help the POS

    system to detect the scanner. The

    very first time the PC might install

    some general drivers, possibly from

    your computer or setup CD.

    In case KB emulation is selected you

    can select various „Key Board

    languages‟ or the universal „Alt-input-

    method‟ (=default). You may want to

    try programming bar codes 3.4.11,

    3.4.13 or 3.4.14 from the

    Configuration Guide

    In case of KB emulation in

    combination with the ALT-input

    method, check if Num-Lock of your

    keyboard is on.

    In a MS-Windows environment verify

    with the device manager that a HID

    (Human Interface Device) is installed

    for the scanner.

    Check that scanner and POS-system

    or Computer have both been set for

    the same USB protocol

    (KB emulation, COM Port emulation

    or IBM POS protocol).

    See Configuration Manual Chapter

    3.5 for setup codes and reset

    (re-power) the scanner after making

    any changes.

    In case the LED is blinking red and

    the scanner does not read the bar

    code, it has been set for USB-COM

    Port emulation mode and the host

    system (application) has not (yet)

    opened the COM port.

  • Scantech-ID BV

    Amersfoortsestraat 124

    3769 AN Soesterberg

    The Netherlands

    Phone: +31 (0)33 469 84 00

    Fax: +31 (0)33 465 06 15

    E-mail: [email protected]

    Internet: www.scantech-id.com

  • Scantech Sirius S-7030 User Manual
  • Scantech Sirius S-7030 User Guide
  • Scantech Sirius S-7030 PDF Manual
  • Scantech Sirius S-7030 Owner's Manuals

DOC-fa4b47a1:

Recommended for Scantech Sirius S-7030 Owners: DVD752/B01, EX-MR1, Nouveau Pizzeria SN1250 Double Flue

B-SX6T Series, EAD20-1300, MS4980, CL-S703, MK1650-62B14 - Metrologic IS1650 - Wired Stationary Barcode Scanner
  • Printed Matter No. 6159929650_ENIssue No. 01Date 10/2020Page 1 / 20Angle-head Electric NutrunnerProduct InstructionsModel Part numberEAD20-1300 6151656060EAD32-900 6151656070EAD50-900 6151656090EAD50-900-HAD 6151658770EAD70-800 6151656110EAD70-700-HAD 6151658780EAD70-800 SQ1/2 6151658820EAD80- ...

    Model & Doc Type: EAD20-1300 20

  • Voyager™ 1452g SeriesCordless Area-Imaging ScannerQuick Start Guide1452-QS Rev (a)11/14Aller à www.honeywellaidc.com pour le français. Vai a www.honeywellaidc.com per l'italiano. Gehe zu www.honeywellaidc.com für Deutsch. Ir a www.honeywellaidc.com para español. Para Português, ...

    Model & Doc Type: Voyager 1452g Series 4

  • Revel HS Buyer’s Guide Copyright ©2010. All Rights Reserved ZEBEX INDUSTRIAL INC. Page 1 of 4 Revel HS Z-3151HS Advanced Handheld High-Speed Laser Scanner Standard Device PIN-OUT CONFIGURATION RJ 1. RTS_TTL RJ 2. KB Data RJ 3. PC Clock RJ 4. GND RJ 5. CTS_TTL RJ 6. RX_TTL R ...

    Model & Doc Type: Z-3151HS 4

  • DATALOGIC S.p.A., Via Candini, 2 40012 - Lippo di Calderara Bologna - Italy dichiara che declares that the déclare que le bescheinigt, daß das Gerät declare que el FireScan D1XX e tutti i suoi modelli and all its models et tous ses modèles und seine modelle y todos sus m ...

    Model & Doc Type: FireScan D141 12

  • Leitor Argox AS-9500 Imager O novo Leitor de Código de Barras Manual Argox AS-9500g Imager 2D é pequeno, leve, portátil e fácil de usar. Além de fazer a leitura de todos os tipos de código de barra, ele também lê códigos bidimensionais, Maxi Code, Data Matrix, Aztec, Qr ...

    Model & Doc Type: ArgoxScan 9500 154

  • 1 TOSHIBA Thermal Printer B-SX6T/SX8T Series SUPPLY LOADING INSTRUCTIONS This sheet contains only the media and ribbon loading procedures. Please be sure to read the Owner’s Manual in the CD-ROM for further information about this printer. 1. LOADING THE MEDIA The followin ...

    Model & Doc Type: B-SX6T Series 10

  • EasyCoder® PD41/PD42EasyLAN Ethernet Interface Installation InstructionsThese instructions tell you how to install the EasyLAN Ethernet Interface Board in a EasyCoder PD41/PD42 printer. The kit includes the following:• EasyLAN Ethernet Interface BoardRequired ToolsTo install the interface boa ...

    Model & Doc Type: EasyCoder PD41 4

Additional Information:

# Brand Model Document Type/File Pages File Size Last Checked
1 Zebra
DS3608
456 18/06
2 Godex
EZ-6000PLUS
8 16/03
3 Datalogic
Lynx D
2 07/12
4 Intermec
CN51
174 18/06
5 Century
Hawk 4
50 04/05
6 Unitech
MS282
169 26/01
7 Wasp
WPL205
2 07/01
8 Citizen
CL-S703
80 2.12 Mb 12/02
9 Datalogic
GRYPHON Mx30
18 0.31 Mb 12/12
10 SATO
CL412e
288 3.28 Mb 12/12
11 Godex
RT860i
68 07/03
12 Aidcti
ERB-2109
44 07/05
13 Di-soric
ID-04
368 17/03
14 kENDALL
Electric Cognex DataMan 260
56 06/01
15 Metrologic
StratosS MS2222
68 21/04
16 SATO
CLe RFID
2 0.71 Mb 23/03
17 Motorola
MC75A
2 06/02
18 Datalogic
DRAGONM131
20 04/03
19 ISSYZONEPOS
MNS009
22 21/12
20 Datalogic
Magellan 9800i
25 19/12
Popular Right Now:
# Brand Model Document (PDF) Pages Size Check Date
1 Cadillac
2011 Escalade
1 1.63 Mb 01.04.
2 HP
Voltaire InfiniBand Grid Director 4200 QDR
7 16.06.
3 Boss
B-506
4 13.04.
4 Raytech
TR-1
21 15.06.
5 LY International Electronics
PM - 210U
10 23.03.
6 AGA
Six-Four Series
44 0.59 Mb 06.06.
7 Trimble
Trimble DUO
20 03.03.
8 ZyXEL Communications
Prestige 645R-A Series
251 4.72 Mb 12.03.
9 Krone
AM 203 CV
56 15.12.
10 MoJack
MoJackPRO
29 11.02.
11 Morphy Richards
IB22078
6 11.06.
12 FAAC
E145
56 01.06.
13 Cintropur
NW 18
3 11.01.
14 Continental Girbau
CG115-25
64 06.05.
15 Yamaha
DX27
25 3.8 Mb 04.05.
16 Samsung
SGH-A617
139 29.02.
17 Giant
ANTHEM X ADVANCED SL 0
1 0.25 Mb 14.02.
18 Art
Model 416
2 0.21 Mb 08.01.
19 Simplicity
1694677
2 0.25 Mb 15.03.
20 WP
MIG 135i
27 03.05.
21 Russell Hobbs
RHSS75
45 12.06.
22 chinavasion
CVYI-E234
10 25.05.
23 Tamron
SP A08
10 0.15 Mb 15.03.
24 Zanussi
102280
2 0.17 Mb 02.04.
25 Viking
ME 339
448 22.12.
Operating Impressions, Questions and Answers: