Ekofires Eko 3010 Manual, Installation & User's Instructions

Manual, Installation & User's Instructions for Ekofires Eko 3010 Indoor Fireplace (20 pages)

Specifications:

747/747648-3010.pdf file (18 Jan 2024)
  • Manufacturer: Ekofires
  • Category of Device: Indoor Fireplace
  • Document: Eko 3010, File Type: PDF Installation & User's Instructions
  • Updated: 18-01-2024
  • Count of Pages: 20
Download Eko 3010 Manual (20 pages)

Ekofires Eko 3010: Read PDF Manual Online

Data: UPD 18th January 2024

Ekofires Eko 3010 Indoor Fireplace PDF Installation & User's Instructions (Updated: Thursday 18th of January 2024 09:19:37 AM)

Rating: 4.8 (rated by 89 users)

Compatible devices: Eko 3020, eko 2010, eko 5510, 1030, EKO 3030, 5510, eko 3021, eko 4010.

Recommended Documentation:

Ekofires Eko 3010: Text of Manual, Installation & User's Instructions

(Ocr-Read Version Summary of Contents, UPD: 18 January 2024)
  • INSTALLATION & USER INSTRUCTIONS

    All instructions must be handed to the user for

    safekeeping.

    RADIANT/CONVECTOR INSET GAS FIRE

    Please note : Except where otherwise stated, all rights, including

    copyright in the text, images and layout of this booklet is owned by

    Focal Point Fires plc. You are not permitted to copy or adapt any of

    the content without the prior written permission of Focal Point Fires

    plc.

    1

    Revision F - 03/13

    © 2013 Focal Point Fires plc.

    GB IE

    BS 7977-1 : 2009

    BS EN 509 : 2000

    KM579168

    IN THE UK ALWAYS USE A GAS SAFE REGISTERED ENGINEER TO INSTALL, REPAIR OR SERVICE THIS APPLIANCE

    MODEL SHOWN: EKO 3020

    Christchurch, Dorset BH23 2BT

    Tel: 01202 588 638

    Fax: 01202 499 639

    www.ekofires.co.uk

    e-mail: [email protected]

    PLEASE NOTE: EKO 3010, 3015, 3020, 3025 GAS FIRES MAY BE SUPPLIED WITH DIFFERENT FRET &

    FRAMES THAN SHOWN

    MODELS COVERED BY THESE INSTRUCTIONS

    3010, 3015, 3020 & 3025 GAS FIRES*

    *AVAILABLE WITH MANUAL, SLIDE CONTROL & REMOTE CONTROL

  • • This appliance is an Inset Decorative Fuel Effect appliance which provides radiant warmth utilising the latest type

    burner technology.

    • The fire is designed to suit various types of fireplaces and natural draught flues as detailed in this manual.

    • The appliance must be installed by a competent person in accordance with Gas Safety (Installation and Use)

    Regulations 1998. It is strongly recommended that a GAS SAFE registered engineer be used for this purpose.

    • Read all these instructions before commencing installation.

    • This appliance must be installed in accordance with the rules in force and used only in a sufficiently ventilated

    space.

    • The appliance is designed for installation on to a non-combustible hearth of at least 300mm depth.

    • This appliance is factory set for operation on the gas type, and at the pressure stated on the appliance data plate.

    • In the event of gas leakage from the appliance, the gas supply must be turned off at the nearest isolating valve.

    • The appliance must be installed in accordance with the following:

    • Failure to comply with the above could lead to prosecution and deem the manufacturer’s warranty invalid.

    • The appliance is designed to fit various types of situations as described in sections 3.0 and 4.0.

    • It should be noted that heaters create warm air currents. These currents move heat to wall surfaces next to the

    heater. Installing the heater next to vinyl or cloth wall coverings or operating the heater where impurities in the air

    (such as tobacco smoke, candle smoke etc.) exist, may cause the walls to become discoloured.

    • WARNING: The manufacturer of this appliance considers all surfaces as working surfaces with the exception of

    the control knob(s) and ash pan door.

    • As with any gas fire, a fire guard complying with BS 8423 must be used in presence of pets, children,

    and the elderly or infirm.

    • Consult ALL instructions before installation and use of this appliance.

    • This appliance is free from any asbestos material.

    • Refractories and fuel bed are constructed from ceramic fibre.

    • Remote control models : These appliances features a battery-operated control system, and under normal usage

    will need a new battery approximately every twelve months.

    Refer to the appropriate section of these instructions for details of how to change the battery.

    I N S T A L L A T I O N I N S T R U C T I O N S

    2

    GB IE

    • Manufacturers' Instructions.

    • The Building Regulations issued by the Department for Communities and Local Government, the Building Standards

    (Scotland)

    (Consolidation) Regulations issued by the Scottish Development Department.

    • Relevant British Standards insofar as the relevant areas are not covered by these instructions.

    • For Republic of Ireland, reference should be made to the current edition of IS813 (the relevant standards governing

    installation).

    1.0 IMPORTANT NOTES

    © 2013 Focal Point Fires plc.

    Section

    1.0

    2.0

    3.0

    4.0

    4.1

    5.0

    6.0

    7.0

    7.1

    8.0

    9.0

    10.0

    11.0

    12.0

    13.0

    14.0

    15.0

    Contents

    Important Notes

    Appliance Data

    Installation Requirements

    Site Requirements

    Debris Collection Space

    Ventilation

    Pre-Fabricated Flue Boxes

    Unpacking the Appliance

    Component Checklist

    Preparing the Appliance

    Preparing the Opening

    Gas Supply Routing

    Installation by Cable Fixing Kit

    Fitting the Burner

    Gas Connection

    Fuel Bed Layout

    Fitting the Firefront / Frame

    Page No.

    2

    3

    3

    3

    4

    5

    5

    5

    5

    6

    6

    7

    7

    7

    8

    8

    8

    Section

    16.0

    16.1

    16.2

    16.3

    16.4

    16.5

    16.6

    16.7

    16.8

    17.0

    17.1

    17.2

    17.3

    17.4

    17.5

    17.6

    17.7

    18.0

    Contents

    Testing and Commissioning

    Operating the Fire (Manual control)

    Operating the Fire (Remote control)

    Operating the Fire (Slide control)

    Spark Gap

    Operating Pressure

    Flue Spillage Monitoring System

    Testing for Spillage

    Briefing the customer

    Servicing

    Cleaning the Ceramics

    Removing the Burner

    Dismantling the Burner

    Pilot Assembly

    Removing the Firebox

    Replacing the Batteries

    (

    Remote control versions)

    Replacing the Batteries (Slide control versions)

    Troubleshooting Guide

    Page No.

    8

    8

    8

    9

    9

    9

    9

    10

    10

    10

    11

    11

    11

    11

    11

    11

    11

    12

  • 2.0 APPLIANCE DATA

    3

    Model

    Destination

    Country

    Cat

    Operating Pressure

    (±2.0 mbar)

    Max Energy Input (kW) Min Energy Input (kW)

    Natural Gas G20 G25

    G30 G31 Gross Net Gross Net

    Manual control GB - IE

    I

    2H

    20 - - - 6.2 5.6 3.5 3.15

    Remote control GB - IE

    I

    2H

    17.5 -

    - - 6.2 5.6 3.5 3.15

    Slide control GB - IE

    I

    2H

    20 -

    - - 6.2 5.6 3.5 3.15

    GB IE

    3.0 INSTALLATION REQUIREMENTS

    Specifications Manual Control Models Remote Control Models Slide Control Models

    Main burner injector Stereo size 78 Stereo size 78 Stereo size 78

    Oxypilot SIT 9090 SIT 9090 SIT 9090

    Gas Control Copreci 21400 Series Mertik Maxitrol GV34 Series Teddington TESA 3173/011

    Gas Inlet All models - 8mm compression - Inlet restrictor elbow

    Ignition Double-action piezo Spark Piezo Spark Piezo Spark

    Spark Gap 3.5 - 4.5mm 3.5 - 4.5mm 3.5 - 4.5mm

    Flue specification

    All models - 225mm x 225mm (9in x 9in) brick or stone.

    125mm (5in) minimum diameter lined brick or stone.

    125mm (5in) minimum diameter twin wall flue conforming to BS 715.

    Pre-cast block flue complying with BS 1289 or BS EN 1858.

    This appliance MUST NOT be installed into a room containing a bath or shower, or where steam may be present. The fire has been

    designed to fit into a builders’ opening or fireplace conforming to BS 1251 or BS EN 1858 (and meeting certain dimensional require-

    ments), or a suitable flue box complying with the constructional requirements of BS 715. The flue box must be installed onto a suitable

    non-combustible insulating surface at least 12mm thick, covering the entire base area of the box.

    A natural draught flue system is required, and if previously used for solid fuel or oil burning, the flue and chimney must be swept prior

    to appliance installation. The flue must have an effective height of at least three metres, as measured from the hearth to the top of the

    flue. Any flue damper plates or restrictors should be removed and no other restriction fitted to the flue. Where removal is not practi-

    cal, the restriction must be fixed in the fully open position. The flue must be checked before installation by using a smoke pellet or sim-

    ilar to ensure proper draw and that leakage is not evident at any joints. Repair and re-test as necessary before the appliance is installed.

    The flue must be connected to only one fireplace, and the flue must not vent more than one appliance (i.e. not shared with a gas back

    boiler). There must be no opening in the flue apart from the one that the appliance is installed into, and the one venting the gases into

    the air. A suitable terminal may be fitted, such as class GC1, as regulations allow.

    This appliance has been tested for use in a pre-cast block flue complying with BS 1289 or BS EN 1858. In accordance with BS 1289 part

    1, pre-cast flues built with directly plastered faces (front or rear) are not correctly installed as to ensure proper operation with any type

    of gas fire. In some instances of this flue construction, temperature cracking of the surface plaster may occur through no fault of the

    appliance. An air gap or some form of insulation material should be installed to prevent normal flue temperatures from damaging wall

    surfaces. Pre-cast flues must be checked for mortar fangs and correct installation of joints, flue sections in loft space and terminals.

    This appliance has been tested for use with circular flues of a minimum internal diameter of 125mm.This appliance is suitable for use

    with a “lightweight” surround and back panel of 150°C minimum rating.

    The fireplace opening should be inspected and repairs made where necessary. Any chair brick or fireback may be left insitu, providing

    that the dimensional requirements for debris collection space and spigot clearances are met. See figure 1.

    The opening WIDTH and HEIGHT dimensions should be between 350mm and 450mm wide, and 540mm to 575mm high. For flues used

    with solid fuel, the minimum WIDTH is 380mm.

    Opening DEPTH should be 200mm or greater for a clay/cement lined or Pre-cast flue which is new, unused, or previously used only with

    a gas appliance. DEPTH should be 240mm or greater for a flue used for solid fuel of oil burning appliances. Opening DEPTHS include

    any plaster or infill panels which form part of the installation.

    4.0 SITE REQUIREMENTS

    Please see Data Badge affixed to appliance for current data. This appliance is for use only with the gas type, and at the pressure stated

    on the appliance Data Badge, and is for decorative purposes.

    © 2013 Focal Point Fires plc.

  • 4.0 SITE REQUIREMENTS - CONTINUED

    GB IE

    4

    All models : This appliance requires a natural draught flue system which may be one of the following;

    225mm x 225mm (9in x 9in) brick or stone.

    125mm (5in) minimum diameter lined brick or stone.

    125mm (5in) minimum diameter twin wall flue conforming to BS 715.

    Pre-cast block flue complying with BS 1289 or BS EN 1858.

    Any existing under grate draught device must be sealed off. The opening wall must be non-combustible.

    The appliance requires a hearth with non-combustible surface of at least 12mm thick. The top surface must be at least 50mm above the

    surrounding floor level, or be surrounded by a raised edge or fender 50mm high.

    To enable the products of combustion to be cleared properly up the flue, the outlet at the back of the appliance must have a 50mm min-

    imum clearance between it and the back wall of the opening or any other obstruction. The area immediately above the outlet must form

    a smooth path into the flue.

    Any type of fire surround used with this appliance must be adequately sealed to the wall and floor.

    A combustible shelf may be fixed to the wall above the fire, providing that it complies with the dimensions given below.

    A non-combustible shelf may be fitted to within 10mm of the top edge of the fireframe. Combustible materials, such as wood, may be

    fitted to within 100mm of either side of the fireplace opening, providing the forward projection does not exceed 100mm. Any com-

    bustible side walls must be at least 500mm to the side of the radiant heat source. As with all heating appliances, any decorations, soft

    furnishings, and wall coverings (i.e. flock, blown vinyl and embossed paper) positioned too close to the appliance may discolour or scorch.

    The mounting depth of this appliance is 108mm (120mm - Convector models).

    In accordance with BS 5871 part 2, minimum debris collection volumes are required behind the installed appliance. These are shown

    below and as dimension ‘X’ in figure 1.

    CLAY/CEMENT LINES OR BLOCK FLUE WHICH IS NEW, UNUSED, OR PREVIOUSLY ONLY USED WITH A GAS FIRE.

    X Dimension = 20mm

    UNLINED FLUE OR CHIMNEY WHICH HAS BEEN PREVIOUSLY USED FOR A SOLID FUEL OR OIL BURNING APPLIANCE

    X Dimension = 60mm

    4.1 DEBRIS COLLECTION SPACE

    © 2013 Focal Point Fires plc.

    Maximum depth of shelf

    Minimum distance from finished

    hearth surface to underside of shelf

    100mm (4in) 745mm (29

    1/4

    in)

    150mm (6in) 845mm (33

    1/4

    in)

    203mm (8in) 895mm (35

    1/4

    in)

    Note : Italics refer to Convector models.

    ‘A’. Opening height: 540mm min/575mm max.

    ‘B’. Opening width: 350mm min/440mm max.

    (380mm min/440mm max.)

    ‘C’. Mounting depth: 108mm (125mm).

    ‘D’. Hearth must extend minimum of 150mm either

    side of the opening.

    ‘E’. Hearth must extend minimum of 300mm in front

    of the opening.

    ‘F’. Non-combustible hearth must be a minimum of

    50mm in height, or be surrounded by 50mm high

    fender.

    ‘G’. 470mm, this area must be flat and vertical to

    ensure a good seal.

    ‘H’. 585mm, this area must be flat and vertical to

    ensure a good seal.

    ‘X’. Debris collection space - See section 4.1.

    ‘A’

    ‘C’

    ‘B’

    ‘E’

    ‘F’

    ‘G’

    ‘H’

    ‘X’

    ‘D’

    Figure 1

  • No purpose provided ventilation is normally required for this appliance. The requirements of other appliances operating in the

    same room or space must be taken into consideration when assessing ventilation. If spillage is detected when commissioning the appli-

    ance, then amongst other problems there may be insufficient natural ventilation for correct operation of the flue. If the appliance does

    not spill with the windows open, but spillage is detected with the windows closed, this demonstrates a lack of natural ventilation. If

    spillage is still detected with the windows open, the flue is at fault. Installation of an air brick is the best solution to lack of ventilation.

    Any ventilation fitted must comply with BS 5871 part 2 and BS 5440 part 2. Vents fitted under or within the immediate vicinity of the

    appliance must not be used as adverse effects to the operation of the ODS may occur. Spillage detected during commissioning is almost

    always a result of poor flue performance that cannot be corrected by any amount of ventilation. For Republic of Ireland ventilation may

    be required, see IS 813, ICP3, IS 327, and any other rules in force.

    This appliance can be fitted into a number of proprietary flue

    boxes provided that the minimum dimensions shown in figure 2

    are complied with.

    Constructional Note: The frame of the fire, any back panel or

    other infill panels, and the flue box must be sealed together so that

    there is no possibility of leakage between them. Adequate clear-

    ances to combustible materials (e.g. false chimney breast con-

    struction) must be maintained.

    The manufacturers’ instructions for fitting the prefabri-

    cated box shall be complied with at all times. To fit the fire

    using the cable fixing kit, some minor adaption may be necessary

    for certain flue boxes. A check should be made to ensure the fire-

    box does not obscure the flue box outlet. The firebox, base of the

    flue box, and hearth below may be drilled to allow plugs and

    screws to secure installation. It is important that the sealing

    requirements of the appliance are met at all times and that the flue

    box is well sealed to any back or infill panel. Note: The DEPTH

    dimension is inclusive of any back or infill panel.

    Stand the carton the right way up, cut the strapping bands and remove the top endcap. Read all the instructions before continuing to

    unpack or install this appliance. Remove the box containing the firefront, and the bags containing the ceramic components. Remove the

    cardboard packing pieces, and any other bags or boxes containing fittings or other parts. When all loose parts have been removed, the

    outer sleeve may be lifted off to reveal the appliance. Check that the components supplied correlate with the component checklist given

    in section 7.1. Please dispose of all the packaging materials at your local recycling centre.

    5.0 VENTILATION

    GB IE

    6.0 PREFABRICATED FLUE BOXES

    125mm min internal dia. twin wall flue

    Radiant models:

    125mm min

    depth

    Convector

    models:

    140mm min

    depth

    Radiant models: 350mm min opening width

    Convector models: 380mm min opening width

    540mm

    min height

    Figure 2

    7.0 UNPACKING THE APPLIANCE

    7.1 COMPONENT CHECKLIST

    QUANTITY DESCRIPTION

    1 Firebox and burner tray assembly

    1 Decorative frame

    1 Firefront

    1 Black Moulded ceramic fibre combustion matrix (coal effect versions only)

    1 Beige Moulded ceramic fibre combustion matrix (Pebble effect version only)

    11 Individual ceramic coals (rounded coal effect version only)

    15 Individual ceramic coals (ripped coal effect version only)

    15 Individual ceramic pebbles (pebble effect version only)

    2 Ceramic fibre side cheeks (pebble effect & ripped coal effect)

    1 Ceramic rear panel

    1 Ceramic taper pad (radiant models only)

    1 Remote control handset (remote control models only)

    1 Cable fixing kit; 2 cables, 2 tensioners, 2 cable clamps, 4 fixing eyes, 4 wall plugs

    1 Sealing grommet

    3 Lengths of adhesive sealing strip

    1 Self tapping screw pack; 4 No.8 x 5/16

    1 Spigot restrictor

    1 Deflector baffle

    1 Set of manufacturers instructions

    1 Slide control position marking sticker (slide control models only)

    1 Slide control knob and M4 Nyloc nut (slide control models only)

    5

    © 2013 Focal Point Fires plc.

  • Note: Ensure that the gas supply is isolated before commencing installa-

    tion of the appliance.

    The fireplace opening and environment must be in compliance with specifications

    laid down in the appropriate sections of these instructions. Remove the appliance

    from the carton as described previously and stand on a dust sheet or similar. Place

    the coals/pebbles, ceramics and fixings safely to one side. Remove the burner from

    the assembly by removing the two screws retaining the tray legs. The tray is now free

    and may be lifted away.

    SPIGOT RESTRICTOR :

    If fitting the fire into a Class 1 or good Class 2 flue, attach the spigot restrictor to

    the rear of the appliance using screws provided as shown in figures 3 and 4. If spillage

    is detected during the commissioning of the appliance, the spigot restrictor should

    be removed immediately.

    SUPPLY PIPE ENTRY :

    Knockout holes are provided in the rear and sides of the firebox for use where con-

    cealed pipework is required. Where necessary, knock out the appropriate hole with

    a sharp tap from a hammer, and fit the rubber grommet supplied. A small incision can

    now be made in the rubber to slip snugly around the outside of the pipe and sleev-

    ing. Do not install or use the appliance without the seal in place. If a hole is

    inadvertently opened, reseal with an intact grommet. Failure to fit the seal correctly

    will cause flue suction to act upon the area under the burner, resulting in poor per-

    formance and intermittent cutting out of the burner.

    SEALING STRIPS :

    Apply the self adhesive sealing strips to the back

    of the fireframe as shown in figure 5 to give a

    continuous seal.

    SLIDE CONTROL MODELS : The control

    knob is supplied as a loose part. Insert the control

    knob into the hole in the top of the slide control

    spindle (Figure 6). Secure the control knob in posi-

    tion using the M4 nyloc nut provided. Affix the Slide

    control position marking sticker on the trim next

    to the control knob as shown in figure 16.

    Before installing the fire, check the flue using a smoke pellet. All of the smoke should travel up the flue and exit correctly from the ter-

    minal.

    If problems are found, DO NOT fit the fire until corrective action is completed. Protect the decorative hearth whilst pushing the fire-

    box in and out of the opening. Part of the packaging will make an ideal hearth saver pad. Before running the gas supply into the open-

    ing, offer up the firebox to the fireplace to check the fit is good.

    Ensure that it slides in correctly, the sealing face sits flat and square to the wall or infill panel, and that the base is firm on the floor of

    the opening as no leaks are permissible here. At this stage it is essential to ensure that the spigot outlet of the fire is not restricted in

    any way. Remove the firebox and take any necessary measurements before making good and preparing for final installation.

    CABLE FIXING :

    For fixing of the fire by the cable method, see the relevant section. The cable fixing locations should be marked on the back of the open-

    ing and the holes drilled. Fit the wall plugs and eyebolts to these holes.

    SCREW FIXING :

    For fixing by screw, mark and drill the fireframe or base, and the relevant points in the opening or on the wall. wall plugs will again be

    required. Pre-punched holes are not provided for this purpose to allow you to choose the optimum positions.

    GAS SUPPLY :

    Following preparation for the fixing method, the concealed gas supply, where required, can now be put into place. Refer to the gas sup-

    ply section for suggested pipe routes. The ends of the sleeving in which the gas pipe is run should be sealed. The ends of the 8mm sup-

    ply pipe should be temporarily sealed to prevent the ingress of debris during fixing.

    PLEASE NOTE: Ensure fire can be removed for ease of servicing and not silconed

    8.0 PREPARING THE APPLIANCE

    GB IE

    6

    © 2013 Focal Point Fires plc.

    Figure 5

    Figure 3 - Convector models

    Figure 4 - Radiant models

    9.0 PREPARING THE OPENING

    Figure 6

  • When the opening is ready for installation of the fire, the gas supply may be routed as per the examples shown in figure 7.

    Wherever a concealed connection is made a rubber grommet must be used to seal the firebox.The gas pipe must be suitably protected

    where it passes through fireplace openings. Any sleeving should be sealed to the pipe at its ends. This appliance is fitted with an inlet restric-

    tor elbow. Using 8mm diameter pipe, connect the appliance to the gas supply point. The appliance must be fitted with rigid or semi-rigid pipe

    of 8mm external diameter. The appliance is factory fitted with an inlet restrictor elbow. Use a minimum length of 8mm pipe, less than 1.5m

    where possible, as a long run of pipe may cause an unacceptable drop in the supply pressure. The open end of the supply pipe should be

    sealed temporarily during the installation to prevent the ingress of dirt and dust.

    Soldered joints are not recommended.

    Drill four holes using a 8mm masonry bit to a depth of 42mm in the positions shown in figure 8. If the fireplace configuration does not allow

    the exact layout given, the eyebolts should be

    positioned as close to the correct layout as

    possible. Before finally fitting cables, ensure the

    self adhesive sealing strips are in position on

    the back of the appliance frame. The fireframe

    must be sealed evenly to the fireplace opening

    all around the periphery. Thread the tensioning

    cables through the holes in the top of the fire-

    box, then the eyelets, and finally through the

    lower holes in the back of the firebox, as shown

    in figure 9. Note : The burner must be

    removed as per relevant section to gain access

    to the cable adjusters. Push the appliance back

    into the fireplace, centralise, and pull the loose

    tensioning cables through the holes into the

    firebox.

    Thread the tensioner bolts onto the cables,

    with the nuts screwed down close to the ten-

    sioner head. Slide the screwed nipple onto the

    cable, pull cable tight, and tighten nipple. The

    tension of the cable may now be adjusted by using a suitable spanner on the tensioner nuts to pull the

    appliance tightly against the fireplace opening. Visually inspect the seal and reseat if necessary. Do not

    cut off excess cable. Surplus cable must not be cut off, as it will be impossible to refit the fire after

    servicing. Coil up the surplus cable, and locate at rear of firebox.

    Temporarily fit the burner tray and ensure a suitable gas route can be achieved. Place the burner tray into the firebox making sure that the

    rear lugs locate properly on to the ledge in the firebox.

    Manual and remote control models : Fit the two securing screws through the tray legs to secure the assembly.

    Slide control models : Fit the four securing screws - two through the

    tray rear first and then two through the legs of the tray to secure the assem-

    bly - see figure 10. Reconnect the slide mechanism by replacing the M4 nut and

    serrated washer on the assembly.

    All models : Connect the gas supply and tighten the gas connections. Fit the

    deflector baffle to

    the two locations

    on the front face of

    the firetray as

    shown in figure 11.

    Screws are provid-

    ed for this purpose.

    The baffle should

    be level with the

    lower edge of the

    tray. Place contemporary firefront in front of the fire temporarily to check the

    angle of the baffle. The front should fit well and the control devices beneath should

    not be visible to the eye. Realign the baffle slightly if necessary to achieve the cor-

    rect fit.

    Purge the gas supply thoroughly to remove air and dirt/debris BEFORE connec-

    tion. Now disconnect the inlet restrictor elbow from the inlet pipe.

    Connect the previously installed gas supply to inlet restrictor elbow, and re-fit the

    restrictor elbow to the inlet pipe of the appliance.

    7

    © 2013 Focal Point Fires plc.

    10.0 GAS SUPPLY ROUTING

    GB IE

    11.0 INSTALLATION BY CABLE FIXING KIT

    ‘A’

    ‘B’

    ‘C’

    ‘A’. 250 mm

    ‘B’. 350 mm

    ‘C’. 60 mm

    All dims ±10mm

    Figure 8

    Figure 9

    12.0 FITTING THE BURNER

    Figure 11

    FIN:

    A

     

    Figure 10

    Manual and

    Remote con-

    trol models :

    The burner is

    secured by two

    screws through

    the tray legs only.

    Slide control

    models : The

    burner is secured

    by four screws as

    shown here.

    IMPORTANT :

    Slide control

    models - Fit the

    rear screws first.

    Fi

    gu

    r

    e 7

    M

    an

    u

    al

    c

    on

    t

    r

    ol

    S

    l

    i

    d

    e c

    on

    t

    r

    ol

    R

    em

    ot

    e c

    on

    t

    r

    ol

    F

    i

    r

    ep

    l

    a

    c

    e o

    p

    en

    i

    n

    g

    G

    r

    o

    m

    m

    et

    s

    F

    i

    r

    eb

    o

    x

    I

    n

    l

    e

    t

    r

    e

    s

    tr

    i

    c

    to

    r

    e

    l

    bo

    w

  • If running a concealed gas supply, ensure grommets are secure around incoming pipes.

    Important Note: Check the thermocouple nut connection into the rear of the valve is secure.

    Please refer to section 7.0 of the user instructions.

    All models : Remove all protective film and packaging material before fitting.

    One-piece frame models : The appliance is supplied with a one piece decorative frame that

    is attached to the front of the firebox with the magnets provided. Position the firefront in front

    of the burner.

    Three-piece frame models : The clip-on frame pieces should be hooked over the outer edges

    of the fireframe, (figure 12), and pushed firmly home. The sides should be fixed first, followed by

    the top bar, which overlaps the sides. Push firmly home.

    IMPORTANT : Due to the possibility of sharp edges, care should be taken when han-

    dling the three-piece frame components. The use of protective gloves is strongly rec-

    ommended.

    Cast frame models : Remove the decorative frame from it’s protective packaging. The frame is retained onto the firebox with a mount-

    ing bracket at the top of the frame and three magnets on each leg of the frame.

    Turn on and test the gas supply up to the fire for any leaks, in accordance with the current edition of BS6891. When the appliance is first

    used, protective oils coating the firebox may burn off. It is advisable to ventilate the room during this period for at least one hour.

    The pilot is visible through the left hand side of ceramic fuel matrix. When cold, the coals or pebbles may be rotated for good viewing.

    The fire features a ‘twin spark’ ignition system to aid lighting,

    Push the control knob in fully and turn anti-clockwise through both of the SPARK positions, keep-

    ing fully depressed, hold there for a few seconds. If the fire has not been used for some time, hold

    the knob in this position for longer, to allow any air in the pipes to be purged.

    Continue turning anti-clockwise through the spark clicks to the nine o’clock position, ensuring

    the pilot has lit. If not, return the knob clockwise, and repeat.

    When the pilot lights after one of the two sparks, keep the knob depressed in the nine o’clock

    position for approximately ten seconds. Now release the knob and the pilot should stay alight. If

    the pilot is extinguished during use, wait three minutes before repeating the ignition procedure.

    To achieve the HIGH setting, push the control knob in slightly and continue turning anti-clock-

    wise to the high position. The main burner should light after a few seconds. To decrease the set-

    ting to LOW, push the knob in slightly and turn the control knob clockwise to the low setting.

    To turn to the pilot only position from the HIGH or LOW positions, press the control knob in, and return to the nine o’clock position

    and release. To turn the fire OFF, keep the knob pressed in, return to the off position and release.

    The pilot is visible through the left hand side of the matrix. When cold, the coals or pebbles may be rotated for good viewing.

    Turn the main burner control (shown on left hand side of control valve) knob fully

    anti-clockwise.

    Turn ignition knob (shown on right hand side of control valve) slightly left towards

    the ignition position until reaching the stop, press down and hold for 5 seconds

    (only pilot gas is flowing)

    Continue pressing down the knob while turning further to the left to activate the

    piezo spark, continue to hold the knob down for a further 10 seconds after the

    pilot has been lit. If the pilot does not light repeat the previous steps.

    8

    © 2013 Focal Point Fires plc.

    13.0 GAS CONNECTION

    14.0 FUEL BED LAYOUT

    16.0 TESTING AND COMMISSIONING

    15.0 FITTING THE FIREFRONT/FRAME

    Figure 12

    GB IE

    FIN:

    A

    16.1 OPERATING THE FIRE - MANUAL CONTROL MODELS

    16.2 OPERATING THE FIRE - REMOTE CONTROL MODELS

    FIN:

    A

    : No reference

    1

    Figure 13

    Figure 14

  • Upon lighting and after the further 10 seconds, release the knob and turn further to the left to the

    ON position. The main burner will light and be controlled in accordance with the main burner con-

    trol knob setting. Adjust the main burner control knob to the desired setting.

    If the pilot is extinguished during use of the fire, you MUST wait ten minutes before repeating the

    ignition procedure.

    To turn the main burner OFF whilst keeping the pilot flame lit, turn the ignition control knob to the

    pilot position then only the pilot will remain lit.

    To shut the fire off completely, press the ignition control knob down and continue turning to the

    right from the pilot position to the OFF position.

    A safety interlock prevents re-ignition of the pilot flame until the thermocouple has cooled suffi-

    ciently to allow the magnetic valve unit to reset itself.

    The remote control unit allows operation of the main burner setting between maximum and pilot

    only setting. It does not permanently turn the pilot on or off.

    The remote control handset incorporates an inbuilt safety feature to prevent the main burner being

    activated or turned up accidentally. It is necessary to press buttons 1 and 2 (see figure 15) simulta-

    neously to turn the fire up. To turn the fire down press button 3 only.

    The pilot is visible through the left hand side of the matrix. When cold, the coals or pebbles may be

    rotated for good viewing.

    Push the slide control knob fully downwards to the SPARK position, and hold there for approxi-

    mately ten seconds. Now release the knob and the pilot should stay alight. When the pilot light has

    established, move the slide control knob upwards to the LOW flame setting. If the pilot is extin-

    guished during use, wait three minutes before repeating the ignition procedure.To achieve the HIGH

    setting, move the slide control knob upwards to the HIGH flame setting. The fire can also be set to

    operate anywhere between HIGH and LOW by moving the control knob to an intermediate posi-

    tion.

    To turn the fire OFF, move the slide control knob upwards fully to the position marked ‘O’.

    The spark gap between the spark electrode and the thermocouple should be 3.5 - 4.5mm

    to produce a good spark.

    There should be no need to adjust this. If under any circumstances the electric spark fails,

    the pilot may be lit manually by proceeding with the ignition sequence as previously

    described, and after moving the control knob through the spark position, the knob should

    be held in (slide control models - down) and the pilot lit with a taper.

    Light the fire on the HIGH setting.

    To commission the appliance, the operating pressure must be in accordance with the figures stated in section 2.0 of these instructions.

    The fire is factory set to achieve the correct flow rates at the specified operating pressure. Any significant variation in the operating pres-

    sure could indicate a supply problem. If the operating pressure is too high the gas supply meter/governor may be set incorrectly. This

    should be checked with the fire running and if necessary reset by the gas supplier. If the operating pressure is too low, then check the

    meter/governor pressure with the appliance running. Upon satisfactory checking of the operating pressure, turn the fire off, disconnect

    the pressure gauge and refit the test point screw. Light the fire and check for gas soundness. In the event that the operating pressure is

    not in accordance with the figures stated in the data section of these instructions, the appliance must not be commissioned, and the

    problem investigated and rectified.

    This fire is fitted with a flue spillage safety device (ODS). If the fire shuts down during use for no apparent reason then several things

    may be suspected. If a door or window has been opened creating a draught, then pilot disturbance is the problem, and removal of the

    draught should resolve this. The gas pressure reaching the fire must also be checked (again, recall your installer to check and rectify any

    problem). The thermocouple connection into the back of the gas control valve may also have worked loose during installation, simply

    get the installer to tighten. If pilot disturbance is not the cause, then the ODS safety system may be in operation. Switch the appliance

    OFF, check the flue and carry out any remedial work required. Relight the fire and carry out a spillage test. DO NOT allow the appli-

    ance to be used if it continues to fail a spillage test. The aeration hole of the pilot must be carefully cleaned out on each annual service

    to ensure continued function of the ODS.The spillage monitoring system shall not be adjusted, modified, or put out of operation by the

    installer. Any spare parts fitted MUST be of a type supplied for the purpose by the appliance manufacturer. If the fire is not spilling, then

    further guidance should be sought, using the Troubleshooting section as a guide.

    9

    © 2013 Focal Point Fires plc.

    16.4 SPARK GAP

    16.5 OPERATING PRESSURE

    16.2 OPERATING THE FIRE - CONTINUED

    GB IE

    16.6 FLUE SPILLAGE MONITORING SYSTEM

    1

    2

    3

    Figure 15

    16.3 OPERATING THE FIRE - SLIDE CONTROL MODELS

    Figure 16

    Figure 17

    Spark gap

  • Close all doors and windows to the room containing the appliance. Let the fire run on HIGH for five minutes. Take a smoke

    match, light it, and using a smoke match tube, hold it at the top edge of the fire opening, 25mm down and 25mm in. Starting 50mm in

    from either side, run the smoke match across the opening.

    All the smoke should be drawn away up the flue. Any smoke returning into the room indicates that spillage is occurring. If the initial

    spillage test fails, run the fire for a further 10 minutes and repeat the test.

    When the test has been completed satisfactorily, repeat with any extractor fans in the premises running on the highest setting, and any

    communicating doors open. Finally, repeat with all doors open.

    DO NOT allow the fire to be used until the test is satisfactorily passed.

    All instructions must be handed to the user for safekeeping. Show the customer how to light and control the fire. After commissioning

    the appliance, the customer should be instructed on the safe use of the appliance and the need for regular servicing. Frequency of serv-

    ice depends on usage, but MUST be carried out at least once annually. Advise that cleaning of the fire may be achieved when the fire is

    cold using a damp cloth and mild detergent on most surfaces.

    Scratched and other superficial damage to the matt black paintwork of the appliance can be covered with matching heatproof spray. Use

    only the manufacturers’ recommended spray paint. Paint only when the fire is OFF and cold. Always mask off the surrounding area to

    prevent contamination with overspray. Ventilate the room during the use of the spray. DO NOT attempt to wash the coals or ceramics

    with water.

    Advise that the fire will emit a “newness” smell for a time after initial commissioning and that extra ventilation may be needed during

    this time. Advise that the fire is fitted with a spillage safety device (O.D.S.). If the fire shuts down, this system may be in operation. If

    spillage is suspected, SWITCH APPLIANCE OFF and call in the installer to investigate any problems.

    Isolate the fire from the gas supply. Ensure that the fire is fully cold before attempting service. A suggested procedure for servicing is

    detailed below.

    10

    © 2013 Focal Point Fires plc.

    16.7 TESTING FOR SPILLAGE

    Match

    Crimp

    Tube

    Figure 18 : Cross section of smoke match tube

    Make a smoke match tube from 10mm diameter

    tube. Seal off one end and crimp the tube to prevent

    the smoke match from sliding down inside.

    Spillage test - Figure 19

    A. 25mm down from top of

    opening

    B. 25mm in from front of open-

    ing.

    C. Disregard outer 50mm

    either side of fireplace opening

    C

    C

    B

    A

    Fireplace Opening

    Smoke Match

    In Tube

    Figure 20

    GB IE

    16.8 BRIEFING THE CUSTOMER

    17.0 SERVICING

    1. Lay out the dust sheet and tools.

    2. Carefully remove the ceramic components.

    3. Remove the firefront fret or the combined frame and firefront (dependant on model).

    4. Disconnect the gas supply, and remove the burner securing screws (see figure 10 and refer to section 17.2)

    5. Remove the burner tray.

    6. Remove firebox as described in section 17.5.

    7. Check the fireplace opening for rubble accumulation and remove. If debris is excessive, initiate remedial work on the flue.

    8. Check the flue with smoke pellet for correct operation.

    9. Refit firebox using new seals where necessary.

    10. Strip off the burner pipes and clean thoroughly.

    11. Clean out the injector, pilot assembly and burner tube. DO NOT attempt to remove the pilot injector.

    12. Re-assemble and re-fit the burner tray.

    13. Turn on the gas supply, and leak test.

    14. Refit the decorative casting and ceramics.

    15. Check any purpose provided ventilation is un-obstructed.

    16. Light the fire and test for spillage.

    17. Check the operating pressure (see section 16.5) and safe operation of the appliance.

    For specific servicing instructions, see the relevant sections.

  • 11

    Remove the firefront and place to one side. Remove the ceramic components. Gently clean in the open air. Be careful not to create dust

    from the coals. Where necessary replace damaged components with genuine spares. Seal scrap ceramic components in plastic bags and

    dispose at proper refuse sites as directed.

    Re-fit the ceramic fuel bed by referring to the relevant section of these instructions.

    Remove the firefront. Remove the ceramics and place safely aside.

    Manual control models : Remove the two screws securing the tray legs to the firebox. Pull tray forward slightly and lift away.

    Slide control models : Remove the four screws securing the tray to the firebox (two in the tray legs and two in the rear of the tray

    - see figure 10). Remove the M4 nut from the slide control linkage. Pull tray forward slightly and lift away. When re-fitting replace the

    rear retaining screws first, followed by the front (leg) retaining screws.

    All models : Be sure to engage the tray location lugs on the shelf at the rear of the firebox.

    Remove the tray as previously described. The pilot unit can be removed by withdrawing the tubing nut, the thermocouple nut on the

    valve, and the two securing screws, and lifting away. Remove the tubing nut from the valve end of the pilot pipe, and blow through to dis-

    lodge any debris. Remove the two tubing nuts on the ends of the gas pipe to the injector elbow and blow clear. Remove the two tub-

    ing nuts on the ends of the inlet pipe and blow clear.

    Manual control models : The valve is not field serviceable.

    Slide control models : The valve contains a gauze filter on the inlet manifold. Check that this is free from debris/obstruction.

    Remove the burner unit as previously described. The pilot unit can be removed by withdrawing the tubing nut, the thermocouple nut on

    the rear of the valve, and the two securing screws, and lifting away. Remove the tubing nut from the valve end of the pilot pipe, and blow

    through to dislodge any debris.

    Clean the pilot assembly with a soft brush and blow through. Check the aeration holes are free of any dirt or lint. Clean thoroughly

    internally, the connection can be removed from the base of the pilot unit using two spanners to make cleaning easier. Do not damage

    or try to remove the pilot injector. The unit is factory set and the only check necessary is to ensure the spark gap is correct. See spec-

    ifications for gap setting.

    Remove the burner unit. Protect the hearth from potential damage. Unroll the coiled tensioner cables from the rear of the firebox.

    Remove the securing nipples and tensioner adjusters. The firebox is now released from the opening and can be slid outward onto the

    hearth. Inspect the fireplace opening for debris and if excessive rectify the flue before proceeding further. Check the seal around the fire-

    frame and if necessary replace. Refitting of the firebox is as described in the fitting section of these instructions.

    Handset - Remove cover from rear of handset and insert 1 x ‘PP3’ (9 volt) battery - Replace

    cover

    Appliance - Ensure appliance is off and cool. Remove cover from top of receiver box. The

    cover is protected by reflective foil, and located towards the right hand side, underneath the

    burner unit. Insert 4 x ‘AA’ (1.5 volt) batteries - Replace cover.

    Ensure appliance is off and cool. The battery is located in the front of the ignition unit, on

    the right hand side of the burner (shown in figure 20). Unscrew the battery holder cap. Insert 1 x ‘AA’ (1.5 volt) battery. Replace cap.

    Slide control models

    Ensure appliance is off and cool. The battery is located in the front of the ignition unit, on

    the right hand side of the burner (shown in figure 22). Unscrew the battery holder cap. Insert 1

    x ‘AA’ (1.5 volt) battery. Replace cap.

    © 2013 Focal Point Fires plc.

    17.1 CLEANING THE CERAMICS

    17.2 REMOVING THE BURNER

    17.4 PILOT ASSEMBLY

    17.5 REMOVING THE FIREBOX

    GB IE

    17.6 REPLACING THE BATTERIES (REMOTE CONTROL VERSIONS)

    17.3 DISMANTLING THE BURNER

    FIN:

    A

     

     

    Figure 21

    17.7 REPLACING THE BATTERIES (SLIDE CONTROL VERSIONS)

    FIN:

    A

    Figure 22

  • Fire sparks but pilot does not light • No gas to fire, check isolators are open and gas supply is on.

    • Pipework blockage, clean out.

    • Air not fully purged, re purge supply or wait longer.

    • Spark earthing to metalwork, reset gap correctly.

    • Blocked pilot, clean out internally.

    Pilot lights but then goes out • Severe restriction in gas supply: clear obstruction.

    • Faulty thermocouple, replace pilot unit.

    • Blocked pilot, clean out.

    • Blocked lint gauze, clean.

    • Hold control knob in/down for longer.

    • Slide control models only : Ensure that the slide control knob is pushed down fully.

    • If the pilot will not stay lit there could be a problem with contamination of the

    gas supply, drafts, room size and/or ventilation or the thermocouple needs replacement.

    Modifications are dangerous and can have a serious unseen effect on safety.

    NEVER MODIFY OR BEND THE THERMOCOUPLE TO MAKE THE PILOT STAY ALIGHT.

    Fire does not spark at pilot • HT lead detached, refit.

    • Slide control models only - replace battery. See section 10.0 of the user instructions.

    • Check the spark gap (see section 16.4).

    • Faulty piezo unit, replace.

    • Debris shorting out electrode, clean.

    • Spark shorting to metalwork under tray, check routing of HT lead under burner.

    Fire runs for a time • Loose or faulty thermocouple, rectify.

    and then cuts off • Blocked pilot, clean out.

    • Excessive drafts in the room.

    • Excessive flue pull.

    • Fire is too close to an air vent.

    • Dirt or lint in pilot aeration hole or on the lint gauze, clean thoroughly.

    • If the pilot will not stay lit there could be a problem with contamination of the

    gas supply, drafts, room size and/or ventilation or the thermocouple needs replacement.

    Modifications are dangerous and can have a serious unseen effect on safety.

    NEVER MODIFY OR BEND THE THERMOCOUPLE TO MAKE THE PILOT STAY ALIGHT.

    Pilot flame shrinks when • Poor gas flow to fire, check pressure with fire on high.

    fire is on high • If pressure is low, remove any restriction in pipework or valve.

    • Check all isolators are adequately sized and fully open.

    • Check meter pressure is adequate.

    • Firebox grommet seal missing, rectify.

    • If the pilot will not stay lit there could be a problem with contamination of the

    gas supply, drafts, room size and/or ventilation or the thermocouple needs replacement.

    Modifications are dangerous and can have a serious unseen effect on safety.

    NEVER MODIFY OR BEND THE THERMOCOUPLE TO MAKE THE PILOT STAY ALIGHT.

    Fire smells when first lit or in use • Newness smell from brand new appliance.

    • Spillage occurring. Carry out Spillage test and rectify any problems.

    • Combustible materials used in incorrect positions.

    • Firebox grommet seal missing, rectify.

    • Other airborne contaminants such as dust, tobacco smoke, paint vapours.

    12

    © 2013 Focal Point Fires plc.

    18.0 TROUBLESHOOTING GUIDE

    GB IE

  • • The Installation and Servicing of this fire MUST only be carried out by a competent person in accordance with local Codes and/or

    Regulations, Building Regulations and the manufacturer's instructions. Failure to comply with these could lead to prosecution and invalidate

    the appliance warranty. In the event of gas leakage from the appliance, the gas supply must be turned off at the nearest isolating valve. This

    appliance is only suitable for the gas type for which it is supplied.

    • Keep a note of the installer's name and address, the original purchase receipt and the date of installation. Failure to produce this informa-

    tion may invalidate the warranty. The appliance should be serviced regularly to ensure continued safe operation. See the servicing section

    for further reference. Frequency of service will depend on use, but MUST be carried out at least once annually.

    • Parts of this appliance become naturally hot during use. It is recommended that a suitable fireguard is used, especially where young children,

    pets, the elderly or infirm are concerned. The manufacturer of this appliance considers all surfaces as working surfaces with the exception of

    the control knob and control panel.

    • As with any gas fire, a fire guard complying with BS 8423 must be used in presence of pets, children, and the elderly or

    infirm.

    • The appliance should be serviced regularly to ensure continued safe operation. Frequency of service will depend on use, but MUST be car-

    ried out at least once annually.

    • Combustible items, such as flooring and furniture and soft wall coverings (such as blown vinyl or embossed paper), low temperature sur-

    rounds etc may discolour if fitted too close to the fire. See relevant section for further details on clearances to combustibles. No combustible

    materials or flooring should protrude onto the hearth.

    • This appliance incorporates a combustion monitoring system (ODS).

    • DO NOT burn any foreign material on this fire, the ceramic fuel effect components must be of the correct type and laid out in accordance

    with the relevant section of these instructions.

    • Failure to do so could create a hazard or lead to sooting.

    • Before the appliance is installed, the chimney should be swept. All flues should be checked by the installer to ensure there are no defects

    or obstructions that may prevent the flow of combustion products.

    • This appliance is fitted with a flue blockage safety device which will shut down the fire if abnormal flue conditions occur. It is NOT a sub-

    stitute for an independently mounted Carbon Monoxide detector.

    • This fire is supplied with a particular style of firefront. Use of the firefront will ensure an adequate airflow under the firebed for the cor-

    rect functioning of this appliance. Use ONLY the firefront supplied with the appliance. Use of any other firefront could be dangerous.

    • Should any home improvements be carried out to the property after the fire is installed, such as installation of extractor fans for example,

    the fire should be re-checked by a competent person for safe operation.

    U S E R I N S T R U C T I O N S

    A combustible shelf may be fixed to the wall above the fire, providing that it complies with the dimensions given below.

    A non-combustible shelf may be fitted to within 10mm of the top edge of the fireplace opening. Combustible materials, such as wood, may be

    fitted to within 100mm of either side of the fireplace opening, providing the forward projection does not exceed 100mm.

    Any combustible side walls must be at least 500mm to the side of the radiant heat source. As with all heating appliances, any decorations, soft

    furnishings, and wall coverings (i.e. flock, blown vinyl and embossed paper) positioned too close to the appliance may discolour or scorch.

    1.0 IMPORTANT NOTES

    1

    GB IE

    © 2013 Focal Point Fires plc.

    Section

    1.0

    2.0

    3.0

    4.0

    5.0

    5.1

    5.2

    6.0

    7.0

    Contents

    Important Notes

    Clearances to Combustibles

    Fire Guards

    Ventilation

    Operating the fire - Manual control

    Operating the fire - Remote control

    Operating the fire - Slide control

    Flue Spillage Monitoring System

    Fuel Bed Layout - ripped coal effect

    Page No.

    1

    1

    2

    2

    2

    3

    3

    3

    4

    Section

    7.1

    7.2

    8.0

    9.0

    10.0

    10.1

    11.0

    12.0

    13.0

    14.0

    Contents

    Fuel Bed Layout - pebble effect

    Fuel Bed Layout - rounded coal effect

    Servicing

    Cleaning

    Replacing the batteries - Remote control models

    Replacing the batteries - Slide control models

    List of replacement parts

    Installation details

    Service History

    Guarantee - Terms and conditions

    Page No.

    4

    5

    6

    6

    6

    6

    7

    7

    8

    8

    2.0 CLEARANCES TO COMBUSTIBLES

    Maximum depth of shelf

    Minimum distance from finished

    hearth surface to underside of shelf

    100mm (4in) 745mm (29

    1/4

    in)

    150mm (6in) 845mm (33

    1/4

    in)

    203mm (8in) 895mm (35

    1/4

    in)

  • The fireguards specified in BS 8423 are intended to protect people from falling into a fire, prevent burns and reduce the risk of injury,

    particularly to young children and the infirm. In addition it is intended to reduce the risk of fire resulting from clothing and/or other flammable

    materials coming into contact with, or in proximity to, burning fuel and/or hot surfaces.

    Fireguards can be permanently fixed in position or can be moveable, and can incorporate open fires including combination grates, or closed fires,

    including room heaters and stoves. See figures 1 & 2 for fireguard examples.

    The fireguards specified are not intended to reduce the risk of fires caused by flying particles, which are covered by BS 3248.

    No purpose provided ventilation is normally required for this appliance. The requirements of other appliances operating in the same space or

    room, and the results of a spillage test must be taken into consideration when assessing ventilation requirements, this will have been carried out

    by your registered installer. For Republic of Ireland, ventilation may be required, see IS 813, ICP3, IS 327, and any other rules in force.

    WARNING : Ventilation openings (where fitted) must never be blocked or restricted in any way.

    The pilot is visible through the left hand side of ceramic fuel matrix. When cold, the coals or

    pebbles may be rotated for good viewing. The fire features a ‘twin spark’ ignition system to

    aid lighting, Push the control knob in fully and turn anti-clockwise through both of the SPARK

    positions, keeping fully depressed, hold there for a few seconds. If the fire has not been used

    for some time, hold the knob in this position for longer, to allow any air in the pipes to be

    purged.

    Continue turning anti-clockwise through the spark clicks to the nine o’clock position, ensur-

    ing the pilot has lit. If not, return the knob clockwise, and repeat.When the pilot lights after

    one of the two sparks, keep the knob depressed in the nine o’clock position for approxi-

    mately ten seconds. Now release the knob and the pilot should stay alight. If the pilot is extin-

    guished during use, wait three minutes before repeating the ignition procedure.

    To achieve the HIGH setting, push the control knob in slightly and continue turning anti-

    clockwise to the high position. The main burner should light after a few seconds. To decrease

    the setting to LOW, push the knob in slightly and turn the control knob clockwise to the low setting. To turn to the pilot only position from

    the HIGH or LOW positions, press the control knob in, and return to the nine o’clock position and release. To turn the fire OFF, keep the

    knob pressed in, return to the off position and release.

    3.0 FIRE GUARDS

    Figure 1

    Example of moveable fireguard for portable heating appliances

    4.0 VENTILATION

    GB IE

    5.0 OPERATING THE FIRE - MANUAL CONTROL MODELS

    FIN:

    A

    Figure 3

    2

    © 2013 Focal Point Fires plc.

    Key

    1. Optional base section for total enclosure of a wall mounted appliance

    2. Points for attachment to a wall.

    Figure 2

    Example of detachable fireguard

    Key

    1. Detachable fireguard

    2. Screw eye

  • The pilot is visible through the left hand side of

    the matrix. When cold, the coals or pebbles may

    be rotated for good viewing.

    Turn the main burner control (shown on left hand

    side of control valve) knob fully anti-clockwise.

    Turn ignition knob (shown on right hand side of

    control valve) slightly left towards the ignition

    position until reaching the stop, press down and

    hold for 5 seconds (only pilot gas is flowing)

    Continue pressing down the knob while turning further to the left to activate the piezo spark, contin-

    ue to hold the knob down for a further 10 seconds after the pilot has been lit. If the pilot does not light

    repeat the previous steps.

    Upon lighting and after the further 10 seconds, release the knob and turn further to the left to the ON

    position. The main burner will light and be controlled in accordance with the main burner control knob

    setting. Adjust the main burner control knob to the desired setting. If the pilot is extinguished during

    use of the fire, you MUST wait ten minutes before repeating the ignition procedure.

    To turn the main burner OFF whilst keeping the pilot flame lit, turn the ignition control knob to the

    pilot position then only the pilot will remain lit.

    To shut the fire off completely, press the ignition control knob down and continue turning to the right

    from the pilot position to the OFF position.

    A safety interlock prevents re-ignition of the pilot flame until the thermocouple has cooled sufficiently to allow the magnetic valve unit to

    reset itself. The remote control unit allows operation of the main burner setting between maximum and pilot only setting. It does not per-

    manently turn the pilot on or off.

    The remote control handset incorporates an inbuilt safety feature to prevent the main burner being activated or turned up accidentally. It is

    necessary to press button 1 and 2 (see figure 5) simultaneously to turn the fire up. To turn the fire down press button 3 only.

    The pilot is visible through the left hand side of the matrix. When cold, the coals or pebbles may be

    rotated for good viewing.

    Push the slide control knob fully downwards to the SPARK position, and hold there for approximately

    ten seconds. Now release the knob and the pilot should stay alight. When the pilot light has established,

    move the slide control knob upwards to the LOW flame setting. If the pilot is extinguished during use,

    wait three minutes before repeating the ignition procedure.To achieve the HIGH setting, move the slide

    control knob upwards to the HIGH flame setting. The fire can also be set to operate anywhere between

    HIGH and LOW by moving the control knob to an intermediate position.

    To turn the fire OFF, move the slide control knob upwards fully to the position marked ‘O’.

    This fire is fitted with a flue spillage safety device (ODS).

    If the fire shuts down during use for no apparent reason then several reasons may be suspected. If a door or window has been opened cre-

    ating a draught, then pilot disturbance could be the problem, and removal of the draught should resolve this.

    The fire can then be re-lit in accordance with the previous section. If pilot disturbance is not the cause, then the ODS safety system may be

    in operation. Switch the appliance OFF, call in your installer to check any ventilation and carry out any remedial work required. DO NOT

    allow the appliance to be used until the installation is passed as safe.

    3

    © 2013 Focal Point Fires plc.

    5.1 OPERATING THE FIRE - REMOTE CONTROL MODELS

    6.0 FLUE SPILLAGE MONITORING SYSTEM

    FIN:

    A

    : No reference

    1

    Figure 4

    1

    2

    3

    Figure 5

    5.2 OPERATING THE FIRE - SLIDE CONTROL MODELS

    Figure 6

    GB IE

  • This fire is supplied with 15 ceramic ripped coals.

    Fit the tapered brick pad into the securing brackets in the upper area of the fire-

    box. Place the large brick panel against the rear of the firebox.

    Place the ceramic combustion matrix onto the burner and the ceramic side cheeks

    onto the matrix.

    Place the front row of six coals

    on to the matrix. Ensure the

    coals are firmly against the side

    cheeks as shown in the photo-

    graph. If necessary, pull the coals forward slightly to ensure their rear edges do not

    overhang the flame ports. Corners or rough edges MUST NOT be allowed to enter

    the flame ports. If in any doubt pull the coals as far forward as possible.

    Place the middle row of five coals onto the flats in the matrix. Ensure the coals are

    not put into the holes in the matrix. Place the two end coals firmly against the side

    cheeks and back to the steps on the matrix, turning them on to their sides as

    shown.

    Place the rear row of four coals, making sure that the flat sides are firmly against the

    brick panel and side cheeks as shown.

    The coals must not be crammed together, or inserted into the holes in the matrix.

    A well laid out, generously spaced coal layout will give the best results.

    IMPORTANT : The fire is designed to operate correctly with the coals supplied when assembled according to the

    instructions. Never add to the fifteen coals, or change them for a different type. Never throw rubbish or other mat-

    ter onto the coal bed.

    This fire is supplied with 15 ceramic pebbles. The pebbles may vary slightly in size,

    shape and colour, in order to allow a realistic layout. Fit the tapered brick pad into

    the securing brackets in the upper area of the firebox. Place the large brick panel

    against the rear of the firebox.

    Place the ceramic combustion matrix onto the burner and the ceramic side cheeks

    onto the matrix.

    4

    © 2013 Focal Point Fires plc.

    7.1 FUEL BED LAYOUT - PEBBLE EFFECT

    7.0 FUEL BED LAYOUT - RIPPED COAL EFFECT

    GB IE

    Figure 7

    Figure 8

    Figure 10

    Figure 9

    Figure 11

    Figure 12

    Figure 12

  • Place the front row of six pebbles on to the matrix. Ensure the pebbles are firmly

    against the side cheeks as shown in the photograph. If necessary, pull the pebbles

    forward slightly to ensure their rear edges do not overhang the flame ports. The

    edges of the pebbles MUST NOT be allowed to enter the flame ports.

    Place the middle row of four pebbles onto the supports in the matrix, over the top

    of the holes. Ensure the pebbles are not turned sideways, such that they actually

    enter the holes.

    Place the rear row of five pebbles, making sure that the flat sides are firmly against

    the brick panel and side cheeks as shown. Note: The pebbles must not be crammed

    together, or inserted into the holes in the matrix. A well laid out, generously spaced

    pebble layout will give the best results.

    IMPORTANT : The fire is designed to operate correctly with the pebbles supplied when assembled according to the

    instructions. Never add to the fifteen pebbles, or change them for a different type. Never throw rubbish or other

    matter onto the fuel bed.

    Due to the light colour of the pebbles, some discolouration/sooting is to be expected during normal use.

    This fire is supplied with 11 ceramic moulded coals.

    Fit the tapered brick pad into the securing brackets in the upper area of the fire-

    box. Place the large brick panel against the rear of the firebox.

    Place the ceramic combustion matrix onto the burner.

    Place the front row of five coals on to the matrix. The edges of the coals MUST

    NOT be allowed to enter the flame ports.

    Place the middle row of four coals onto the supports in the matrix, over the top of

    the holes. Ensure the coals are not turned sideways, such that they actually enter

    the holes.

    5

    © 2013 Focal Point Fires plc.

    7.1 FUEL BED LAYOUT - PEBBLE EFFECT - CONTINUED

    GB IE

    Figure 13

    Figure 15

    Figure 14

    7.2 FUEL BED LAYOUT - ROUNDED COAL EFFECT

    Figure 16

    Figure 18

    Figure 17

    Figure 18

  • Finally, place the rear row of two coals.

    IMPORTANT : The fire is designed to operate correctly with the coals

    supplied when assembled according to the instructions. Never add to

    the fifteen coals, or change them for a different type. Never throw rub-

    bish or other matter onto the coal bed.

    The fire and flue should be checked on an annual basis to ensure all of the products of combustion are entering the flue and that there

    is no excessive build up of soot. The frequency of service will depend on usage, but MUST be carried out at least once annually. Servicing

    must be carried out by a GAS SAFE registered engineer.

    Cleaning of the coals/pebbles may be carried out by following the instructions given in section 9.0 of these instructions. The Installation

    instructions carry full servicing details for the use of the installer.

    If debris from the flue or other foreign matter is found on the fire it may indicate a need for servicing. Do not use the fire until the

    source of the debris has been found and rectified. Air vents (where fitted) should be checked periodically to ensure they are free from

    obstruction.

    Before carrying out any of the following operations, ensure that the fire is OFF and completely cold.

    FIREFRONT - Any dust accumulating in the firefront may be removed using a vacuum cleaner or dry cloth. Heavy stains may be removed

    by using a damp cloth and mild household detergent. Brass parts of the firefront may be cleaned using a suitable brass cleaner. Replace

    the front centrally against the fire after cleaning. Do not use a damp cloth to clean cast iron fronts (Soho, and Finsbury models) as this

    can cause the fronts to rust.

    PAINTED AREAS - These can be cleaned using a dry cloth.

    COALS AND CERAMICS - Remove the firefront and place to one side. Remove the ceramic components. Gently clean in the open air.

    Be careful not to create dust from the coals. Where necessary replace damaged components with genuine spares. Seal scrap compo-

    nents in plastic bags and dispose of at proper refuse sites as directed.

    Re-fit the ceramics carefully by referring to section 7.0 of these instructions.

    Handset - Remove cover from rear of handset and insert 1 x ‘PP3’ (9 volt) battery - Replace

    cover

    Appliance - Ensure appliance is off and cool. Remove cover from top of receiver box. The

    cover is protected by reflective foil, and located towards the right hand side, underneath the

    burner unit. Insert 4 x ‘AA’ (1.5 volt) batteries - Replace cover.

    Ensure appliance is off and cool. The battery is located in the front of the ignition unit, on

    the right hand side of the burner (shown in figure 20). Unscrew the battery holder cap. Insert 1 x ‘AA’ (1.5 volt) battery. Replace cap.

    Slide control models

    Ensure appliance is off and cool. The battery is located in the front of the ignition unit, on

    the right hand side of the burner (shown in figure 8). Unscrew the battery holder cap. Insert 1

    x ‘AA’ (1.5 volt) battery. Replace cap.

    6

    © 2013 Focal Point Fires plc.

    8.0 SERVICING

    9.0 CLEANING

    7.2 FUEL BED LAYOUT - ROUNDED COAL EFFECT

    GB IE

    Figure 19

    10.1 REPLACING THE BATTERIES (SLIDE CONTROL VERSIONS)

    10.0 REPLACING THE BATTERIES (REMOTE CONTROL VERSIONS)

    FIN:

    A

    Figure 21

    FIN:

    A

     

     

    Figure 20

  • 11.0 LIST OF REPLACEMENT PARTS

    Item Part number

    Pack of 15 Ripped coals F780094

    Pack of 15 Pebbles F550057

    Pack of 11 Moulded coals F550059

    Ceramic fuel bed - Ripped coal models F780093

    Ceramic fuel bed - Pebble models F780035

    Ceramic fuel bed - Moulded coal models F780034

    Rear ceramic tile and rear taper pad - Hotbox models F550208

    Rear ceramic tile - Convector models F790005

    Oxypilot 9090 - Manual, remote control & slide control models F730057

    Gas valve - Manual control models F730085

    Gas valve - Remote control models F730011

    Gas valve - Slide control models F730067

    Injector - Stereo 78 - Manual & Slide control models F730062

    Injector - Stereo 77 - Remote control models F730047

    Burner assembly - complete - Manual control TRAYSLIM

    Burner assembly - complete - Remote control TRAY 019

    Burner assembly - complete - Slide control TRAY153

    Remote handset and receiver kit F730003/5

    12.0 INSTALLATION DETAILS

    Installer GAS SAFE registration No : Model :

    Fire serial No. :

    Name & contact details of installer : Supplied by :

    Date installed :

    7

    GB IE

    © 2013 Focal Point Fires plc.

  • 13.0 SERVICE HISTORY

    As our policy is one of continuous improvement and development , we hope therefore you will understand we must retain the right to amend details and/or specifications without prior notice.

    8

    F860618

    GB IE

    © 2013 Focal Point Fires plc.

    14.0 GUARANTEE - TERMS AND CONDITIONS

    The 3 year guarantee only covers products purchased on or after 1st February 2009. For all gas fires purchased the 3 year guarantee

    commences from the date of purchase, provided that the following 3 terms and conditions are adhered to:

    Registration is not required.

    1. For any claim to be made within the 3 years from date of purchase you will be required to provide and supply us with your proof

    of purchase.

    2. Your gas fire must have been commissioned by a CORGI/Gas Safe* registered installer, evidence of which you must provide together

    with the CORGI/Gas Safe* registration number.

    3. Your appliance must have been serviced annually, irrespective of use, by a CORGI/Gas Safe* registered installer, evidence of which

    must be provided, such as the receipt.

    Please note all consumable items such as any ceramics including; coals, pebbles, the matrix, front strips, side cheeks, rear panels and

    tapered rear panels are not covered by the 3 year guarantee.For all Electric fires purchased the 3 year guarantee commences from

    the date of purchase, providing that you can supply the proof of purchase. This does not cover consumable items such as pebbles,

    coals or light bulbs.

    Making a claim is easy.

    If you wish to make a claim under our 3 year guarantee and all the terms and conditions for your product have been met then please

    submit the following information for the attention of the 3G Service Department to the address below. Alternatively, you can email or

    fax.Please note that this does not affect your statutory rights.

    Focal Point Fires plc, 3G Service Department, Reid Street, Christchurch, Dorset, BH23 2BT.

    Alternatively email: [email protected] or fax. 01202 499326.

    Details required:

    1. Name, full address including post code and contact telephone number.

    2. Receipt of purchase or credit card statement.

    3. Original installers CORGI/Gas Safe* registration number (gas fires only).

    4. Annual service receipt for every 12 months (gas fires only).

    *Gas Safe Register replaced CORGI as the gas registration body in Great Britain and the Isle of Man on 1st April 2009.

    Date of service Serviced by (name): GAS SAFE No. : Contact details of Engineer

  • Ekofires Eko 3010 User Manual
  • Ekofires Eko 3010 User Guide
  • Ekofires Eko 3010 PDF Manual
  • Ekofires Eko 3010 Owner's Manuals

DOC-93fc1cb5:

Recommended for Ekofires Eko 3010 Owners: GI12117, 8330, SLS

CARODG36I, EPI3, P121, BGD42N, Superior Fireplaces VRE4536RS, COLORADO
  • Save this manual for future reference.OWNER’S OPERATION AND INSTALLATION MANUALVENT-FREE PROPANE/LP GASCOMPACT CLASSIC HEARTH® FIREPLACE®Shown with OptionalCabinet Mantel/HearthBase AccessoryVMH26TPB14,000 to 26,000 Btu/Hrwith ThermostatWARNING: If the information in this manual is notfo ...

    Model & Doc Type: VMH26TPB 14 28

  • Printed in CanadaCONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT RESTRICTIONS AND INSTALLATION INSPECTION REQUIREMENTS IN LOCAL AREA.READ THIS ENTIRE MANUAL BEFORE INSTALLATION AND USE OF THIS WOOD FIRE. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN PROPERTY DAMAGE, BODILY INJURY O ...

    Model & Doc Type: INSPIRE 2000 48

  • Save These Instructions 3-90-775R15_04/13 www.harmanstoves.comOwner's ManualInstallation and OperationModel:P35iPellet/Biomass Fireplace Insert#1-70-774195#1-70-774235SAVE THESE INSTRUCTIONS. Please read this entire manual before installation and use of this replace insert room heater. Fa ...

    Model & Doc Type: P35I 50

  • USER INSTRUCTIONS INSTALLATION INSTRUCTIONS SERVICE INSTRUCTIONS It is a regulation that these instructions be handed to the customer after installation is complete. It is also the responsibility of the installation engineer to ensure that the customer is able to fully operate the appliance ...

    Model & Doc Type: BM-05XXX1 18

  • ANYWHERE FIREPLACE™ The high style and distinctive contemporary design of the Anywhere Fireplace™ allows the ambiance of a fire to be enjoyed in any room, garden or patio. It is ventless, requiring no chimney or gas line because it uses clean burning bio-ethanol liquid fuel speci ...

    Model & Doc Type: Gramercy 6

  • 539042MPL coverInstallation, Operation and Maintenance Manualfor Residential Installation� ...

    Model & Doc Type: MPL11 32

  • 1 Inset Instrucon Guide Models – COLORADO – IOWA – DETROIT – MEMPHIS - KANSAS – KEPLER 22 Important Safety Informaon Always read this manual rst before aempng to install or use this replace. For your safety, always comply with all warnings and safe ...

    Model & Doc Type: COLORADO 20

  • 352013.09.2017 / 53-0667DKSVNOGBDEESITFRNLMontering af stenbeklædningMounting of stone coverMontage von SteinverkleidungMontering av stenbeklädnadMontering av steinbekledningHet monteren van de steen bekledingMontage du set de pierreMontaggio del rivestimento in pietraMontaje del reves ...

    Model & Doc Type: 3520 8

  • Northfield MV Owner’s Manual WARNING: FIRE OR EXPLOSION HAZARD Failure to follow safety warnings exactly could result in serious injury, death, or property damage. - Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appli ...

    Model & Doc Type: Northfield MV 44

  • 1W415-0527 / A / 04.14.11SAFETY INFORMATION- Do not store or use gasoline or other fl ammable vapors and liquids in the vicinity of this or any other appliance.- WHAT TO DO IF YOU SMELL GAS:• Do not try to light any appliance.• Do not touch any electrical switch; do not use a ...

    Model & Doc Type: ZCVF36 16

Additional Information:

# Brand Model Document Type/File Pages File Size Last Checked
1 Lennox
MERIT PLUS
32 09/06
2 Desa
GMC11FD
4 08/05
3 Heat & Glo
SL-550METRO-LP
77 6.58 Mb 15/02
4 Flavel
Warwick FIRC**MN
12 02/02
5 Riello Burners
RS 25/M BLU
72 08/12
6 Real Fires
RF800M(N/P) Modern
44 23/02
7 White Mountain Hearth
DVD32FP3 Series
52 10/02
8 Kingsman
ZRB46
74 18/04
9 Prokonian
Monte Carlo
4 19/05
10 Heatmaster
enviro 17
4 25/03
11 Pacific energy
G963
34 04/05
12 Nordpeis
Uno 1
52 28/12
13 Dimplex
DF2024
13 16/04
14 Firenzo
Royale
14 07/03
15 Monessen Hearth
Peninsula 624WBPF
1 22/05
16 Regency
P33-NG4
64 7.99 Mb 09/05
17 metrofires
Tiny Rad Woody
16 01/04
18 Town & Country Fireplaces
TCWS.38CE3
44 08/03
19 Belleze
050-HA-50118
12 29/04
20 Montigo
DelRay DRL3613NI-2
40 25/05
Popular Right Now:
# Brand Model Document (PDF) Pages Size Check Date
1 Bryant
T2-PAC
40 1.07 Mb 03.04.
2 Accurate Technology
TK100
14 11.06.
3 Matsui
M100WM09
24 08.06.
4 Creative
TravelSound for iPod nano 4th gen
1 1.53 Mb 13.04.
5 IVT
PL-828
28 14.06.
6 Haibrain
SW12
16 22.04.
7 White
404
48 5.26 Mb 29.02.
8 Beam
IsatDock2 MARINE
2 12.06.
9 Konig
HAV-SB250
50 08.01.
10 Directed Electronics
VA200
1 0.02 Mb 08.06.
11 PDi
PD251-031A
9 05.01.
12 Toshiba
Satellite L50
142 17.12.
13 Cobra
XRS9840
21 14.03.
14 WERTHEIM
Deep Clean W3000
20 13.03.
15 Danfoss
VACON 100 industrial
148 12.03.
16 Superlux
E205U
14 11.04.
17 Triple S Customs
Car Security
61 13.05.
18 D-Link
PCMCIA WIRELESS ASAPTER DWL-650
4 10.58 Mb 07.03.
19 MPMan
BTC244
7 31.05.
20 Mocet
IP3062
74 25.02.
Operating Impressions, Questions and Answers: