Extron electronics AVTrac 68-1405-01 Installation Manual

AVTrac
™
 Rough-In Adapter Installation Guide
This adapter is designed for installation in new stud wall 
constructions, prior to installing the gypsum board walls 
(drywall).
1.  Determine where AVTrac will abut the wall.  (See the 
AVTrac Installation Guide [part number 68-1405-01] for 
factors that must be considered before installation.)  
Cut out a section of the wall base stud that is 4” 
(10.1 cm) wide and align the front edge of the adapter 
base with the front edge of the wall base stud (see the 
figure at right).
2.  Mark the position of the holes in the adapter base, 
and drill at least two holes into the 
concrete 5/32” (0.4 cm) diameter and 1 1/2” (3.8 cm) deep.  Secure 
the adapter to the floor with the provided masonry screws.

Dry Wall
Rough-In Adapter
Front Support
4.0"
1.5"

Wall Base Stud
Rough-In Adapter Base
(Front edge is level with
  wall base stud.)
(2) Masonry
     Screws

3.  Cut a notch 1.5” (3.8 cm) high x 4” (10.1 cm) wide 
in the bottom edge of the drywall and place the 
drywall over the rough-in adapter with the top edge 
of the notch resting on top of the adapter’s front 
support.  Secure the drywall to the wall frame (see 
the figure at left).
4.  Install the AVTrac system.  For complete information 
about installing the AVTrac system, consult the 
AVTrac Installation Guide.

Extron Electronics, USA
800.633.9876  714.491.1500  
FAX  714.491.1517
Extron Electronics, Europe
+800.3987.6673  +31.33.453.4040
FAX +31.33.453.4050
Extron Electronics, Asia
+800.7339.8766  +65.6383.4400  
FAX  +65.6383.4664
Extron Electronics, Japan
+81.3.3511.7655
 FAX  +81.3.3511.7656
www.extron.com

68-1603-01
Rev A
06 08
AVTrac
™
 Wall Trim Plate Installation Guide
The wall trim plate is a finishing plate that compensates 
for any overcuts to the existing gypsum wall during 
AVTrac intstallation.
Install the trim ring in place of, or behind, existing wall 
base trimmings as follows:
1.  Install the AVTrac system, as described in the AVTrac 
Installation Guide (part number 68-1405-01).
2.  Before snapping the cover track in place and  
covering the track with a carpet or rubber strip, place 
the trim plate against the wall so that it is seated on 
the AVTrac, covering the overcut hole in the wall.
3.  Mark the position of the two holes in the trim ring on 
the wall and, using the screws provided, secure the 
trim plate to the wall.
4.  Snap the cover track in place and cover the track 
and ramps with carpet, as described in the AVTrac 
Installation Guide (part number 68-1405-01).  If 
required, trim the wall baseboard to fit snugly 
around the track and attach it to the wall, over the 
trim plate.

Wall Tr im Plate

• 
  MikroTik RouterOS v2.9

  MikroTik Reference Book: RouterOS v2.9 (#81ML7K)

  RouterOS v2.9, 709, mikrotik/routeros-v2-9.pdf

• 
  SKLZ Quickster Soccer Goal

  Sports & Outdoors Quickster Soccer Goal Document, #O822JN

  Quickster Soccer Goal, 2, sklz/quickster-soccer-goal.pdf

• 
  Uniden GMR2099-2CK

  Two-Way Radio Tutorial #6WJG6D

  GMR2099-2CK, 2, uniden/gmr2099-2ck.pdf

• 
  CFS SX-200

  CFS Guidance: SX-200 (#29O24K)

  SX-200, 11, cfs/sx-200.pdf

• 
  enzie DELUX

  enzie Ladders Manual (#RV7FE1)

  DELUX, 2, enzie/delux.pdf

• 
  tti Tech PMR-122TX

  Radio PMR-122TX Handbook, #I3A8J1

  PMR-122TX, 40, tti-tech/pmr-122tx.pdf

• 
  Wavtech linkD

  #SH71HD: linkD Guidance

  linkD, 12, wavtech/linkd.pdf

• 
  Gloria Thermoflamm

  Gloria Lawn and Garden Equipment Manual (#C91922)

  Thermoflamm, 124, gloria/thermoflamm.pdf

• 
  Schter STSPPILA520000

  Schter Chainsaw Manual (#O7K2C3)

  STSPPILA520000, 27, schter/stsppila520000.pdf

• 
  Piaget 640P

  Reference Book (640P, #OKPEK9)

  640P, 31, piaget/640p.pdf

• Search YouTube Videos for Extron electronics AVTrac 68-1405-01 Device
• Search Google for Extron electronics AVTrac 68-1405-01 Information
• Search Photo of Extron electronics AVTrac 68-1405-01 in Google Images
• Search Twitter for Extron electronics AVTrac 68-1405-01 News