Data: UPD 22nd January 2024
ns design NXT Double Bass Musical Instrument PDF Instruction Manual (Updated: Monday 22nd of January 2024 07:32:08 PM)
Rating: 4.9 (rated by 24 users)
Compatible devices: NS WAV4 Radius, NXTa Omni Bass, CS1X, MM100, NS-CR4 Radius Bas, CLP-990, Pacer 100, NS-NXT4a.
Recommended Documentation:
Text Version of ns design NXT Double Bass Musical Instrument Manual (Summary of Contents)
(Ocr-Read of Document's Main Page, UPD: 22 January 2024)
NXT
Double Bass Instructions
STAND
Open the legs wide for stability, and secure in place with thumb screw clamp. Mount the instrument to the
stand using the large (5/16”) thumb screw at the top of the stand. Using the adjustment knobs, it is possible to
adjust the height, angle, and tilt of the instrument.
CONTROLS
Knob 1 – Volume with bypass switch – called the JackPot™, the volume control has a switch at the full on
(clockwise) position that bypasses the volume potentiometer for the fullest tone and output level.
Knob 2 - Tone clockwise for full treble, counter-clockwise to cut treble.
Switch - Up for Arco Mode (for optimal bowed and percussive plucked sound).
Down for Pizzicato Mode (for optimal plucked, sustained sound).
The Polar™ pickup allows the player to control attack and decay parameters. Pizzicato Mode is for a smooth
attack and long decay, Arco (percussive) Mode is for massive attack and relatively fast decay. Note that the full
bow response can only be achieved in the Arco Mode.
PASSIVE ELECTRONICS
This is a passive system, so it does not require batteries, and therefore has unlimited headroom for dynamic,
distortion-free response. The large piezo crystal sensors are powerful, and provide plenty of level for most
amps. However, the output impedance is high, and may not match well with amps that are designed for
magnetic coil (electric guitar) pickups. The symptom of poor impedance matching is reduced bass response.
As a result, on some amps the bass control will need to be turned up for best results. Amps with 1 meg ohm or
greater input impedance are recommended.
TRUSS ROD
Use 6mm inch hex wrench. Access is just below the nut. Clockwise rotation tightens the truss rod to decrease
relief. To play well, the surface of the fingerboard should not be perfectly straight, but rather it should have a
slight forward curve from end to end.
STRING HEIGHT
Adjust bridge height with Phillips head screws under the bridge, accessible through the back plate.
STRING REPALCEMENT
The NXT Bass is designed to fit standard NS Electric Double Bass Strings. Replacement NS strings should be
available from your dealer. Conventional acoustic double bass strings can also be used. However, acoustic
strings are much longer, extending far beyond the bridge. To avoid adding this extra length to the body of the
instrument, extra string slots are provided on the back so that the long strings can wrap around the end of the
body.
ATTACHING STANDARD ACOUSTIC DOUBLE BASS STRINGS
To install standard acoustic strings, thread the strings through the holes in the body from the back, then wrap
the strings around the end of the instrument and hook the ball ends into the key holes in the back plate. The
strings are then threaded into the tuners in the normal manor.
Sales :
Technical :
[email protected]
[email protected]
Recommended:
HDR-CX500E, Ektapro 3020, 6110 - Navigator Smartphone 40 MB, Tacoma 2005
Portatone PC-1000, MRS-1044CD, RS-101 Strings, KT-76, AP800
-
ENDEFRESEnglishDeutschFrançaisEspañolFeaturesInput Channels...................................................................page 12With up to 16 (MG166CX/MG166C: 10) mic/line inputs or up to four stereo inputs, the MG mixer can simultaneously connect to a wide range of devices: microphones, lin ...
Model & Doc Type: MG206C 29
-
1. Attach the steel legs to the base of the instrument with the M8 Nyloc Nuts and 2 part security caps. (1.1) (See Assembly Guide)Surface FixedInstallation Instructions(1.1)(1.2)Instrument Components:6. Attach the 1 pair of beater to the saddle strap on the leg. (1.3)Surface Fix C ...
Model & Doc Type: Rainbow Trio Metallophone 3
-
PSR-OR700 Installation Procedure Caution: Do not turn off the power or remove the USB flash memory during this operation. Confirming the version number 1)Turn on the power of the instrument and wait until the main display appears. 2)Press the [FUNCTION] button, then select [UTIL ...
Model & Doc Type: PSR-OR700 4
-
Roland HP 237R user manualhttp://www.manuallib.com/file/2725302From ManualLib.comManualLib.com collects and classifies the global product instrunction manuals to help users access anytime and anywhere, helping users make better use of products.Home: http://www.manuallib.com/ Chinese: ...
Model & Doc Type: HP 237R 45
Operating Impressions, Questions and Answers:
