Data: UPD 20th November 2023
Antique Radios PRO-528 Scanner PDF Quick Start Manual (Updated: Monday 20th of November 2023 05:55:37 PM)
Rating: 4.4 (rated by 16 users)
Compatible devices: XR3D-6, Professional Enhanced Scan Tool 9640A, Slide and Negative Converter, ZR4, Camescope KV-S1025C, A60+, PATRIOT P15, eScan Series.
Recommended Documentation:
Text Version of Antique Radios PRO-528 Scanner Manual (Summary of Contents)
(Ocr-Read of Document's Main Page, UPD: 20 November 2023)
PRO-528 1,000 Channel
Handheld Trunking Scanner
20-528
step 1: insert batteries
Insert four AA batteries (not supplied). You must set the ALKALINE
JACK NiMH switch inside the battery compartment to the
appropriate setting.
Warning: Do not connect an adapter to the scanner if non-
rechargeable batteries (such as alkaline batteries) are installed in the
scanner. Attempting to recharge non-rechargeable batteries may
cause harm to you or the scanner.
• ALKALINE when using alkaline batteries (not included).
• NiMH when using rechargeable (NiMH) AA batteries (not included).
Note that the scanner stops charging automatically after 14 hours.
step 4: use additional features
See your User’s Guide for more information on your scanner’s
features.
storing known frequencies into channels
Visit http://radioreference.com/ for local frequencies.
1. Press
E/PGM to put the scanner in programming mode.
2. Use the number keys to enter the channel number where you want
to store a frequency.
3. Press
SCAN/MANUAL.
4. Use the number keys and
•/CLR/DELAY to enter the frequency
(including the decimal point) you want to store.
5. Press
E/PGM to store the frequency into the channel.
service bank search
1. Press SVC. The current service symbol appears and the scanner
starts to search.
2. To select a different service bank, press
1/HAM, 2/MRN, 3/AIR or 4/POL.
The newly selected service symbol appears. Press
e
or
d
to search
up or down.
QUICK START GUIDE
06A06
UBZZ69344ZZ(0)
Printed in China
step 2: connect antenna
Attach the supplied antenna to the scanner by aligning
the slots around its base with the tabs on the scanner,
then slide into place.
step 3: scan preprogrammed channels
Your scanner is preprogrammed with 150 frequencies in channels 1-150.
1. Turn
SQUELCH fully counterclockwise.
2. Turn
VOLUME/OFF clockwise until it clicks and you hear a hissing sound.
3. Press
SCAN/MANUAL if SCAN is not shown in the display.
4. Turn
SQUELCH clockwise until the hissing stops.
See the User’s Guide for a
complete description of your
scanner’s buttons.
transferring data from another scanner or pc
You can upload programmed data from another PRO-528 scanner using a connecting cable (available at your local RadioShack store). Or upload
programmed data from a PC using an optional PC interface cable (available at your local RadioShack store) and software (visit http://starrsoft.com
and http://scancat.com/).
storing trunking frequencies into channels
1. Press E/PGM in conventional mode to set the scanner in
programming mode. Then, press TRUNK. Your scanner beeps. The
TRUNK and all of the bank numbers ash.
2. Press the number key (1-9 and 0) of the desired target storage bank.
Select one of the trunk systems by repeatedly pressing
e
or
d
to
select a trunking system type, then press E/PGM.
3.
Prog F appears, then press E/PGM. The scanner automatically selects
the rst channel in the selected banks.
4. Use the number keys to enter a valid frequency within the trunk
system, then press E/PGM. The bank number, the channel number,
and E (EDACS), M (Motorola), or L (LTR) appears depending upon
the trunk system selected.
5. Press
e
or
d
to select the next channel in the bank and repeat Step 4
to enter frequencies in that bank.
6. Repeatedly press
•/CLR/DELAY to return back to Step 2. Repeat Steps 2
and 5 until all frequencies have been entered.
7. Press
SRCH to begin searching for the trunk’s data channel and scan
conventional frequencies at the same time. As the scanner reviews
You must set the
ALKALINE JACK
NiMH switch inside the
battery compartment to the
appropriate setting.
Recommended:
DMR-EH80VEB, LMH Series, Aurora 720, TX-76PW05A
MDT 10, Q-Wash 250, DESIGNJET 700, bizhub 350, FB1210U, X1-Scan
-
One buttonscanning tosearchable PDFBusinesscard scanning Scan directlyto Microsoft® applicationsEasily protect,preserve, & sharedocumentsNew multi-function QuickMenu featureIncluded to work with Microsoft® Windows® Operating Systems Providing Authentic Adobe PDF CreationPFU CardMind ...
Model & Doc Type: S510 - ScanSnap - Document Scanner 2
-
Quick Start Guide Bluetooth® Cordless Hand Scanner CHS 7Ci, 7Di, 7DiRx This document pertains to the following CHS models: 7Ci SKU# CX2870-1409 (P/N 8550-00062) 7Di SKU# CX2877-1472 (P/N 8550-00065) 7DiRx SKU# CX2879-1474 (P/N 8550-00066) The part number (P/ ...
Model & Doc Type: CHS 7Ci 12
-
PROVU PD6100 Strain Gauge, Load Cell & mV Meter Instruction Manual Precision Digital Corporation Strain Gauge 15, 30, 150, 300 mV Unipolar Input Ranges ±15, ±25, ±150, ±250 mV Bipolar Input Ranges Selectable 5 or 10 VDC @ 350 mA Maximum Sensor Excitation Supports u ...
Model & Doc Type: ProVu Series 56
-
Getting to Know Your ScanMaker i2400Microtek's new scanner, the ScanMaker i2400, brings a brand new taste to the worldof scanners. With a newly designed laptop-like appearance, the ScanMaker i2400breaks the stereotype of scanner designs and brings a new milestone to the scannerworld. ...
Model & Doc Type: ScanMaker i2400 14
Operating Impressions, Questions and Answers:
