Data: UPD 16th October 2023
Dimplex RXPW4 Controller, Heating System PDF Quick Start Manual (Updated: Monday 16th of October 2023 04:42:58 AM)
Rating: 4.9 (rated by 66 users)
Compatible devices: DXGLO2, VSH LAK9, KNX WPM, DWF1215, DWF1203, DF2550, TIMRA, Duo300N.
Recommended Documentation:
Text Version of Dimplex RXPW4 Controller, Heating System Manual (Summary of Contents)
(Ocr-Read of Document's Main Page, UPD: 16 October 2023)
Quick Start Guide
RXPW4 - 4 Zone Pilot Wire Central Controller
Controls
General
Initial set up: Setting the time and day
Issue 1: D1227-0106
This guide is for quick reference only. Refer to RXPW4 installation and operating instructions for further information
1 - Time
2 - Day of the week
3 - Current mode
4 - Zone status reference
5 - Controller setup/override
buttons
6 - Validation button
7 - Holiday mode
8 - Selector switch index mark
9 - Mode selector switch
Symbol Function
Continuous comfort (all zones)
AUTO Auto mode (heating runs to the preset program for each
zone)
Continuous set back (all zones)
Continuous frost protection (all zones)
Set the time
Off (no heat output)
Heater mode configuration
PROG Set the daily programs
Mode Selector Functions
The RXPW4 controller allows control of multiple Dimplex heaters
from a single point. Heaters can be grouped together in “zones”
and each zone configured with a different time program for each
day of the week. Up to 4 zones are available.
Before the controller can be programmed, it is first necessary to set
the current time and day of the week.
1. Turn the mode selector switch to the position.
2. Use the “+” and “-” buttons to cycle through the hours/
days of the week until the correct time/day is set.
3. Press OK to confirm.
Note: Typically 1 = Sunday, 2 = Monday, etc.
Setting the daily program for each zone
1. Turn the mode selector switch to the PROG position.
2. Use the “+” and “-” buttons to select the zone you wish to
programme (e.g. P=1).
3. Press OK to select.
4. Use the “+” or “-” buttons to set the program for each hour
of day 1 (i.e. Sunday).
5. “+”sets an hour of Comfort (on) and “-” sets an hour of
Background (off). The hours of the day are denoted across
the bottom of the display.
6. Press OK to confirm when the program has been set. The
programme for day 2, etc. can then be set in the same
way..
7. To copy the program from one day to the next, hold down
the OK button for 5 seconds.
Setting the daily program for each zone (cont.)
8. Once the daily programs have been set for Zone 1, repeat
the process for Zones 2 - 4.
9. To run the program, set the mode selector switch to the
AUTO position.
10. The status of each zone is indicated on the display (1 bar =
background (off), 4 bars = Comfort (on).
Temporarily over riding the the daily program
When the programmer is in AUTO mode, the current setting for
each zone can be temporarily over ridden (advanced).
1. Press the OK button. The bars above Z1 will flash.
2. To change the status of zone 1 (e.g. from Comfort to Back-
ground), press the “+” or “-” button, followed by OK to
confirm.
3. Alternatively, to change the status of a different zone, press
the OK button until the bars above the required zone flash
and repeat the steps above to change the status.
4. This will temporarily over ride the program until the next
scheduled status change.
Manual over ride (all zones)
To permanently over ride the mode of all zones, turn the mode
selector switch to one of the manual setting positions:
COMFORT (ON) mode
BACKGROUND (OFF) mode
FROST PROTECTION mode
STANDBY mode
Please refer to the individual
heater instructions to details of
heater operation in each mode
Glen Dimplex UK Ltd. Millbrook House, Hedge End, Southampton, SO30 2DF. For further assistance please contact Dimplex customer services on 0870 727 0101
Recommended:
Traveler L3, WRTR-262GN, Block 642189, Coffee Grinder
Simatic ET 200S, Bluebrain, SA 48.1, XC-CPU101 Series, DOL 534
-
Installation InstructionsOriginal InstructionsPowerFlex 70 Adjustable Frequency AC DriveThis document explains the 5 BASIC STEPS to install and perform a Basic Start-up of the PowerFlex® 70 AC drive. A human interface module (HIM) is required to perform the Basic Start-up routine that i ...
Model & Doc Type: PowerFlex 70 50
-
Pneumatic Control Manual 717.1Receiver-Controllers SectionTechnical Bulletin T-5800-3/-4Issue Date 0586© 1986 Johnson Controls, Inc.1Part No. 24-7029-0, Rev. —Code No. LIT-7171320XT-5800-3 and T-5800-4Dual Input Receiver-ControllersInstallation and CalibrationThe T-5800 Series Receiver-Control ...
Model & Doc Type: T-5800 Series 12
-
12 The Xbox Guide button in the center of your controller puts the Xbox 360® experience at your ngertips. Press and hold the Xbox Guide button to tur ...
Model & Doc Type: Xbox 360 Universal Media Remote 2
-
Translated by R.Whitehead 21-1-2012 for my own use (No liability can be accepted for the result of any errors!) 1 of 4 YGE 200 HV FAI Speed controller for Pylon and Hotliner Technical data: - The max. Full throttle current is 200A for 30 seconds - 4 to 10s LiPo, with low voltage de ...
Model & Doc Type: 200 HV FAI 4
Operating Impressions, Questions and Answers:
