Data: UPD 24th January 2024
Genie S-100 Boom Lifts, Lifting Systems PDF Quick Reference Manual (Updated: Wednesday 24th of January 2024 02:13:12 PM)
Rating: 4.7 (rated by 4 users)
Compatible devices: X-135/70, S-60X, AWP-19, S-120, S-80X, GS-2646AV, GTH-844, GRC-12.
Recommended Documentation:
Text Version of Genie S-100 Boom Lifts, Lifting Systems Manual (Summary of Contents)
(Ocr-Read of Document's Main Page, UPD: 24 January 2024)
Quick Reference Guide
January 2017
Genie S-100 • Genie S-105 • Genie S-120
Genie S-125 • Genie S-100HD • Genie S-120HD
Rev A
S-100 • S-105 • S-120 • S-125 • S-100HD • S-120HD
S
-100 from SN 15D-1001
S
-120 from SN 15D-1012
S
-100HD from SN S100HD15D-212
S
-105 from SN 15D-983
S
-125 from SN 15D-984
S
-120HD from SN S120HD15D-208
This Quick Reference Guide is intended for operators who are properly trained to safely operate the machine.
Getting Started:
Step 1: Read the Operators Manual and Perform the pre-operation inspections and tests.
Step 2
Step 3
Step 4
Step 5
Turn to platform
position.
Pull out Red Emergency
Stop buttons.
Start
Engine.
Verify axles
are extended.
Controls and Indicators:
Axle Extend
Axle extend and retract indicator lights will
flash while the axles are moving. Axle extend
indicator light will stay on when the axles are
fully extended. Axle retract indicator light will
stay on when the axles are fully retracted.
Steer Mode
The indicator light next to the current
steer mode will be on.
Drive Enable
Light on indicates that the boom has moved
past a circle-
end tire and the drive function has
been interrupted. To drive, push the drive
enable button and slowly move the drive/steer
control handle off center. Use the color-coded
direction arrows on the platform box and drive
chassis to identify the direction the machine
will travel.
Engine idle select
Rabbit and foot switch symbol light on
indicates foot switch activated high idle
is selected.
Rabbit symbol light on indicates high
idle is selected.
Turtle symbol
light on indicates low idle
is selected.
Platform Overload
Light flashing indicates the platform is
overloaded. The engine will stop and no
functions will operate. Remove weight from
the platform until the light goes off and then
restart the engine.
Drive Select
Machine on incline symbol
: Low range
operation for inclines.
Machine on level surface symbol
: High
range operation for maximum drive speed.
Fault Indicator Light
Light on indicates the machine has one or
more faults. Faults are abnormal conditions
that exist due to component failure or system
misuse. See the appropriate service manual.
Operating Envelope Indicator Lights
The operating envelope indicator lights will come on to notify the
operator that a function has been interrupted and/or an action is
required by the operator.
Raise Boom light flashing
: To continue
extending the boom, raise the boom until the
indicator light is off.
Retract Boom light flashing
: To continue
lowering the boom, retract the boom until the
indicator light is off.
Platform Not Level light flashing
: The tilt
alarm will be sounding when this light is
flashing. The Platform Level toggle switch
will only work in the direction that will level
the platform. Level the platform until the
indicator light is off.
M
achine Not Level Light Flashing
: If the tilt
alarm sounds when the platform is raised, the
Not Level indicator light will come on and the
drive function in one or both directions will not
operate.
Follow the correct boom lowering sequence
below based on the platform position. Do not
rotate the boom while lowering.
Uphill Position Downhill Position
S
-100 • S- 105 • S-12 0 • S -125 • S-100HD • S-1 20HD
Quick Re fer ence Gui de
Janu ary 201 7
Genie S
-10 0 • Ge nie S- 105 • G enie S-120 Ge nie S-125 • Genie S-100H D • G eni e
S-120HD
Rev A
Recommended:
Floorbased Sound Unit, SF-1523, TSA0502, FSG 90E PC
1930ES, S-80, C5000 Series, Genie GS-1530, Genie Z-62/40, SD50 Series
-
1. Service and Repair ManualPart No. 1268553GTRev A3October 2020From Z513014B-1201 to Z513016M-1999Serial Number RangeZ-51/30JFrom Z5130M-2000This manual includes:Repair proceduresFault CodesElectrical and HydraulicSchematicsFor detailed maintenanceprocedures, Refer to the approp ...
Model & Doc Type: Z-51/30J 144
-
Maintenance Manual - Booms S® Booms This manual includes detailed procedures for each maintenance inspection. Z® Booms For Repair procedures, Fault Codes, Electrical and Hydraulic Schematics, refer to the appropriate Service and ...
Model & Doc Type: Genie Lift Guard S-40 198
-
Service and Repair Manual Serial Number Range Z-34/22 IC from Z3406-4800 This manual includes: Repair procedures Fault Codes Electrical and Hydraulic Schematics For detailed maintenance procedures, refer to the appropriate M ...
Model & Doc Type: Genie Z-34/22 IC 119
-
7/24/18MANLFT/BOOM LIFT/4X4Operating Instructions1. Ensure all emergency stops are out2. Turn key switch at ground control station to Basket position, fully up.3. Ensure function selector hand valve is turned to Basket position, fully up.4. Ensure main engine ignition switch in the engi ...
Model & Doc Type: SP34 2
Operating Impressions, Questions and Answers:
