Quick Reference Manual for Mitutoyo ID-C X series Measuring Instruments (1 pages)
Data: UPD 28th October 2023
Mitutoyo ID-C X series Measuring Instruments PDF Quick Reference Manual (Updated: Saturday 28th of October 2023 02:50:22 PM)
Rating: 4.6 (rated by 56 users)
Compatible devices: CLM-DKX, VL-50A, SURFTEST SV-3100, Digimatic MDC-S, QM-Data 300, LGF-110L-B, LGF-110ZL-B, TM-500 Series.
Recommended Documentation:
Text Version of Mitutoyo ID-C X series Measuring Instruments Manual (Summary of Contents)
(Ocr-Read of Document's Main Page, UPD: 28 October 2023)
OFF
OFF
ON
OFF
ON
SET
SET
MODE
MODE
SET
SET
SET
SET
MODE
MODE
SET
SET
SET
SET
SET
SET
SET
SET
SET
SET
SET
SET
MODE
MODE
MODE
MODE
MODE
MODE
MODE
MODE
MODE
SET
SET
Measurement mode
P
Reverse direction
ID-C X series Quick Reference Manual
Setting tolerance
judgment function
Changing resolution
Setting calculation function
Setting function lock
Press（within 2 sec.）
Press and hold
(2sec. or more)
inch ： 0.00005
0.0001，0.0005
mm ： 0.001，0.01
OFF
ON
OFF
ON
Setting preset value
（ABS mode）
ABS mode ⇔ INC mode
（Preset ） （Zero-setting）
SET
・Power On
・Holding displayed value or
External output of displayed value
Power Off
DATA ON・OFF
Function lock. The content of the
operation has been limited.
Reverse counting
Calculation function display.
Displayed value= Calculation coefficient
× Spindle displacement
◇Meaning of the icons
※
※0.001mm，.00005”model only
To calculation
Coefficient
setting
Selection
sign
next digit
Repeat the above
procedures until
all digits
Complete setting
◎Please see the User’s manual for details.
No.99MAH028B
Selection
Selection
Selection
Selection
Selection
◇Key pressing method
ON
(Normal)
ON
(Enlarged)
No
change
Setting tolerance
Setting preset value
(Refer to the
user’s manual)
Quit setting mode
Upper limit value setting
Changing
Tolerance
limit value
The setting method is the same as the
Upper limit value setting.
Lower limit
value setting
Zero-setting
（INC mode）
・To cancel the setting halfway, press and hold
the MODE key in area . It returns to the state
in front of one. It can return to measurement mode
by repeating the same operation.
・Clears all settings when the battery is put in again.
Forward direction
Switching counting
direction
No
change
Changing
preset value
Selection
value
next digit
in ⇔ mm
（in/mm model only)
Parameter Setting Mode
Recommended:
pmd430, SWWHD-PTCAM, 2 SLICE ACCENTS TOASTERS WITH PAUSE AND CHECK, CT25G6E - 25" COLOR TV
MX06S, Mg41-NE, 1200, ET 200M, Arex 30W
-
modilys® m E.83.0189, Release 1.0.0 CH 2009ista International GmbH – Grugaplatz 2 – D-45131 Essen http://www.ista.com DE Montageanleitung FI Asennusohje PL Instrukcja montażu BE Інструкцыя па мантажу FR Notice de montage PT Instruções de montagem BG Мо ...
Model & Doc Type: modilys m 6
-
1Quick start guideENPower quality analyserThis reference guide does not replace the operating manual!The manual is available on our Web site www.bender.deMake sure that the relevant personnel has read this manual andunderstood all instructions relating to safety.1. Safety instructions 2. In ...
Model & Doc Type: PEM735 4
-
Varian BV Herculesweg 8 4330 EA Middelburg The Netherlands CP-4900 Micro-GC User Manual North/South America 2700 Mitchell Drive Walnut Creek 94598 California, USA Tel: ++(1)9259392400 Fax: ++(1)9259452360 or ++(1)9259452344 Europe P.O. Box 8033 4330 EA Middelburg The Netherl ...
Model & Doc Type: CP-4900 Micro-GC 141
-
(217) 352-9330 | [email protected] | artisantg.com-~ ARTISAN® ~I TECHNOLOGY GROUP Your definitive source for quality pre-owned equipment. Artisan Technology Group Full-service, independent repair center with experienced engineers and technicians on staff. We buy your excess, u ...
Model & Doc Type: L4532A Series 106
Operating Impressions, Questions and Answers:
