Watec WAT-240E Operation Manual

 
1/4”  Miniature  Color  camera 
WAT-240E 
Operation Manual 
This  operation  manual  covers  safety,  camera  functions,  installation  and 
the  correct operating  procedure  for  the  WAT-240E. First,  we  ask  you  to 
read  this  operation  manual  thoroughly,  then  install  and  operate  the 
WAT-240E  as  advised. In  addition,  for  future  reference,  we  also  advise 
safe keeping of this manual. 
Please  contact  the  distributor  or  dealer  from  which  the  WAT-240E  was 
purchased,  if  you  do  not  understand  the  installation,  operation or safety 
instructions laid out in this manual. Not understanding the contents of the 
operation manual sufficiently may cause damage to the camera. 
 
Guide to the Safety Symbols 
The definitions of the symbols used in this operation manual are: 
 
“Danger”, may lead to a serious accident such as death or injury 
caused by fire or electric shock. 
 
“Warning”, may cause severe damage such as a physical injury. 
 
“Caution”,  may  incur  injury  and  cause  damage  to  peripheral 
objects in the immediate surroundings. 
 
Cautions for Safety 
WAT-240E is designed to be used safely, however it may lead to a physical 
accident caused by fire and electric shock if not used correctly. Therefore, 
please  keep  and  read  the  “Cautions  for  Safety”  for  protection  against 
accidents. 
 
Do not disassemble and/or modify the WAT-240E.
 
 
Do not operate the WAT-240E with wet hands.
 
 
  
Use a stabilized power adaptor designed for DC+6V, with 
a current capacity of more than 300mA for the WAT-240E 
The recommended voltage is DC+4.6～6.6V. 
  
Do  not  expose  the  WAT-240E  to  wetness  or  high 
moisture conditions. 
The WAT-240E is designed and approved for indoor use only. 
The  WAT-240E  is  not  water-resistant  or  waterproof.  If  the 
location  of  the  camera  is  outdoors  or  in  an  outdoor  like 
environment,  we  recommend  that  you  use  an  outdoor 
camera housing. 
  
Protect the WAT-240E from condensation. 
Keep  the  WAT-240E  dry  at  all  times  during  storage  and 
operation. 
  
Should  the  camera not  work  properly,  switch  off  the  power 
immediately.  Then  check  the  camera  according  to  the 
“Problems and Trouble Shooting” section. 
 
  
Avoid the striking of hard objects or dropping the   
WAT-240E. 
The  WAT-240E  uses  high  quality  electrical  parts  and 
precision components. 
  
Do  not  wire  the  WAT-240E  with  any  monitor  using  a 
video/power single transmission terminal. The WAT-240E is 
not  designed  for  use  with  this  type of  equipment.  We  also 
advise you to read the operation manual of the monitor  you 
plan to use before any connections are made. 
  
Do  not  install  the  WAT-240E  in  a  position  subject  to 
direct sunlight. 
Sunlight shinning directly onto the WAT-240E lens can cause 
damage to the image sensor. 
  
Select a stable place for installation of the WAT-240E. 
Use  a  support  of  durable  strength  around  an  installation 
position on a ceiling or wall when a camera stand or tripod is 
used. 
  
Do not move the WAT-240E with the cables connected. 
Before  moving  the  WAT-240E,  always  remove  the  video 
cable and power cable from the rear of the camera first. 
 
 
  
Avoid  using  the  WAT-240E  near  any  strong 
electromagnetic field. 
After  installing  into  main  equipment,  if  the  WAT-240E  is 
exposed  to  electromagnetic  waves  causing  the  monitored 
image  to  become  distorted,  we  recommend  the camera  be 
shielded by appropriate protective casing. 
 
Problems and Trouble Shooting 
If any of the following problems occur when using the WAT-240E
,
 
  An optimal picture cannot be obtained, after checking that all the cables 
and connections are correctly in place. 
  Smoke or any unusual odor emerges from the WAT-240E. 
  An  object  becomes  embedded  or  a  quantity  of  liquid  seeps  into  the 
camera housing. 
  More than the recommended voltage or/and amperage has been applied 
to the WAT-240E by mistake. 
  Anything  unusual  occurring  to  any  equipment  connected  to  the 
WAT-240E. 
 
Disconnect  the  camera  immediately  according  to  the  following 
procedures: 
① Switch off the main power supply to the camera. 
② Remove the power and video cables connected to the WAT-240E. 
③ Contact  the  distributor  or  dealer  from  which  the  WAT-240E  was 
purchased. 
 
 
EMC 
The  WAT-240E  is  in  conformity  with  EMC  test  standards  carried  out  by 
authorized organizations in Japan. 
 
NTSC    /FCC Part15 class B 
 
P
 
A
 
L   
 
EN61000-6-3/EN50130-4 
 
Do  not  modify  the  WAT-240E.  A  modified  camera  may  not 
conform to EMC test standards. 
 
 
 
Contents 
Using the contents figures below, check to make sure all parts are present 
before use. 
 
① Lens (Upper: Type G3.8) 
② WAT-240E 
③ Installation ring mount 
④ Screw for ring mount (M2.6 x 8mm) 
⑤ Nut for ring mount (M2.6) 
 
 
 
 
 
 
 
 
Power Supply 
Use  a  stabilized  power  adaptor  designed  for  DC+6V,  with  a  current 
capacity of  more  than  300mA.  Use the  optional  DC  plug  if  the  shape  or 
polarity of the DC plug of the power adaptor to be used is not compatible 
with the camera.   
The wiring on the connector must be exact. 
Be careful not to touch the other terminals while wiring. Protect the wired 
portion by using insulation tape after wiring. If the above care and attention 
is not adhered to, damage to the WAT-240E and power adaptor may occur 
and may also cause fire. 
 
【Diagram of output cable】 
 
【Connection of output cables】 
 
 
Assembly and Setting Up 
■When using the ring mount 
 
【Setting of the ring mount】 
 
Fix the mount by passing  the  ring over the lens of the  camera,  and  then 
attach the thread and nut. 
 
※ Fix  the  ring on  the  housing  with  appropriate  force  and  then  check  to 
make  sure  the  camera  is  fixed  firmly  and  squarely.  Improper  setting 
might cause damage to the camera cover. 
 
Set-up and Operation 
① Refer to the【Connection of output cables】and the wiring must be exact. 
② Join  the  video  out  cable  with  the  video  in  cable  of  the  monitor  or 
peripheral equipment. 
③ Join the power supply using the correct procedure. 
④ Make sure that a picture can be seen on the monitor 
⑤ To  focus,  turn  the  lens  clockwise  or  counterclockwise  while  observing 
the  picture  on  the  monitor. Take  care  when  focusing  not  to scratch  or 
damage the lens. 
 
Options 
 
Holder (H002) 
H002  is  used  for  mounting  the  WAT-240E with 
ring mount. This holder has a U1/4”thread in the 
center  and  a  M2  thread  in  the  four  corners  for 
mounting on stands. 
 
MS-50 (Mini Stand) 
A convenient stand for the WAT-240E. With this 
stand,  the  camera  can  be  adjusted  to  any 
desired angle. 
 
Contact information 
  Design and specifications are subject to change without notice. 
  Watec  is  not  responsible  for  any  inconvenience  or  the  attendant 
damages  to  the  video  and  monitoring  recording  equipment  caused  by 
misuse, mis-operation or improper wiring of our equipment. 
  If for any reason the  WAT-240E does not  work  properly,  or  if  you  have 
any  questions  regarding  installation  or  operation,  please  contact  the 
distributor or dealer from which it was purchased. 
Contact information
 
  Watec Co., Ltd. 
Add.:I 254-2 Nihonkoku, Daihoji, Tsuruoka- Shi, 
Yamagata-Ken, 997-0017 Japan 
TEL:  +81-235-23-4400    FAX: +81-235-23-4409 
E-mail:  [email protected] 
URL:  http://www.watec.co.jp 
1664Z00-Y2000002 

• 
  Avalue Technology EMX-QM57

  Avalue Technology User Guide Motherboard EMX-QM57 (#4RX4OG)

  EMX-QM57, 40, avalue-technology/emx-qm57.pdf

• 
  ROHO Smart Check

  Security System Smart Check Instruction, #8M6CS9

  Smart Check, 14, roho/smart-check.pdf

• 
  Honeywell HD55IP

  HD55IP Security Camera - #PBN4ZX

  HD55IP, 2, honeywell/hd55ip.pdf

• 
  Philips 56188-17-16

  Tutorial (56188-17-16, #1V954A)

  56188-17-16, 8, philips/56188-17-16.pdf

• 
  NordicTrack E7.3 Gw Elliptical

  NordicTrack User Guide Other E7.3 Gw Elliptical (#YB97B7)

  E7.3 Gw Elliptical, 32, nordictrack/e7-3-gw-elliptical.pdf

• 
  Manhattan 175944

  Manhattan Tutorial Headphone 175944 (#6YA4T7)

  175944, 16, manhattan/175944.pdf

• 
  Whirlpool LGR4634PQ

  Dryer LGR4634PQ Instruction, #M8O4Y8

  LGR4634PQ, 16, whirlpool/lgr4634pq.pdf

• 
  Omnimount OM10015

  #3J25V7: OM10015 Guidance

  OM10015, 32, omnimount/om10015.pdf

• 
  zimbo kamin Laser

  Swimming Pool Heater Laser Handbook, #H2LB51

  Laser, 34, zimbo-kamin/laser.pdf

• 
  Valor The Arden

  Handbook (The Arden, #E967J3)

  The Arden, 20, valor/the-arden.pdf

• Search YouTube Videos for Watec WAT-240E Device
• Search Google for Watec WAT-240E Information
• Search Photo of Watec WAT-240E in Google Images
• Search Twitter for Watec WAT-240E News