Data: UPD 13th December 2023
ADTRAN TRACER 1280050L1 Switch PDF Quick Start Manual (Updated: Wednesday 13th of December 2023 07:46:19 AM)
Rating: 4.7 (rated by 95 users)
Compatible devices: NetVanta 1561i-04, Total Access 128-Port CSM, H2TU-C, NETVANTA 1335 SERIES, NetVanta 1235P, NetVanta 1534 PoE, NetVanta 1224ST, 1xN.
Recommended Documentation:
Text Version of ADTRAN TRACER 1280050L1 Switch Manual (Summary of Contents)
(Ocr-Read of Document's Main Page, UPD: 13 December 2023)
TRACER ETHERNET SWITCH MODULE P/N 1280050L1
For more detailed documentation, visit us online at www.adtran.com
Quick Start Guide
Quick Start Guide, 61280050L1-13A, January 2005 Technical Support 1-888-4ADTRAN (1-888-423-8726) Copyright © 2005 ADTRAN, All Rights Reserved
SPECIFICATIONS
Interface Type: (4) 10BaseT/100BaseTX interfaces with auto MDI/MDIX
crossover on all interfaces
Flow Control: Back-pressure flow control on all half-duplex interfaces
Pause-frame flow control on full-duplex interfaces
Environmental
Specifications:
Operating Temperature: -25°C to 65°C
Storage Temperature: -20°C to 70°C
Relative Humidity: Up to 95% non-condensing
Compliance: FCC Part 15, Class A
NETWORK CONNECTION PINOUT
Pin Name Source Description
1 RX1 Attached Equipment Receive Positive
2 RX2 Attached Equipment Receive Negative
3 TX1 Module Transmit Positive
4, 5 UNUSED N/A —
6 TX2 Module Transmit Negative
7, 8 UNUSED N/A —
INSTALLATION INSTRUCTIONS
1. Remove the cover plate from the appropriate option slot in the TRACER
rear panel.
2. Slide the TRACER Ethernet Switch Module into the option slot until the
module is firmly positioned in the chassis.
3. Secure the thumbscrews at both edges of the module. Tighten with a
screwdriver.
4. Connect the cables to the associated device(s).
5. Complete installation of remaining modules and system as specified in
the TRACER 6000 Series System Manual.
The TRACER Ethernet Switch Module is not
hot-swappable. Remove power from the TRACER
system before installing or removing the module.
Recommended:
HDR-1, EX PHONO 2X, PL-100, LS411LED
4126 02, PC-LPM-16/PnP, TE-1820, FS205, CS-W6-SD05GP, USB hub 2.0 6-Port switchable
-
Wattstopper ®InteliSwitch® Digital Time Switch – 120/277VACInstallation Instructions • Instructions d’Installation • Instrucciones de InstalaciónNo: 24164 – 09/16 rev. 1Catalog Number • Numéro de Catalogue • Número de Catálogo: TS-400Country of Origin: Made in C ...
Model & Doc Type: Wattstopper InteliSwitch TS-400 4
-
Terminal Removable (pull down)01+ 01+ I1+ I1- I2+ I2- V+ V- AI+ AI- P N SD CARDTransducer Cable ConnectionsSubmersible Motor: 3-Ph./ 3-W. 1-Ph., follow colors as above.Submersible Motor: 1-Ph./ 2-W., connect to Y and B, any order.Above-Ground Motors: L1 to R, L2 to Y ...
Model & Doc Type: Pentek Intellidrive 2
-
ext_bus 7 10/6/3/0.8.0.31.0 fcparray CLAIMED INTERFACE FCP ArrayInterfacetarget 12 10/6/3/0.8.0.31.0.0 tgt CLAIMED DEVICEdisk 16 10/6/3/0.8.0.31.0.0.0 sdisk CLAIMED DEVICE HPA5277A/dev/dsk/c7t0d0 /dev/rdsk/c7t0d0disk 17 10/6/3/0.8.0.31.0.0.1 sdisk C ...
Model & Doc Type: StorageWorks 7110 - Virtual Array 1
-
SWITCH ACTION (Normally open/Normally closed)Vertical ModelsVertical mount models are shipped with normally open switch contacts which closeas the float rises toward the mounting threads. Reverse switch action by removingthe float, rotating it end-for-end and replacing it on the s ...
Model & Doc Type: F7 Series 2
Operating Impressions, Questions and Answers:
