emmeti CS-11 Operation & User’s Manual

U9310090
 
M
M
M
M
M
Your thermostat has the ability to reset all settings to the factory defaults. If you are certain you want
 to do this: In standby mode(when thermostat is turned off), press and hold button           and      
for 5 seconds until RES is shown on LCD.
Configure the menu
Resetting factory defaults
Setting temperature
Press          or         once, you will see set temperature flashing. Use           or          again to adjust 
to the temperature you want your room to maintain. Press button            to accept and exit.    
Buttons and LCD display
Buttons Press < 5 seconds Press > 5 seconds
Turning on/off thermostat
Menu button
Increase the set value
Decrease the set value
Lock /unlock buttons
Reset to factory settings
(when thermostat is turned off) 
+
+
Confirm settings
The buttons are locked.
Displays when heating is active
Setback mode
Symbol Description
Set temperature
Set At
Sensor selection. This thermostat is a combination model allowing you to choose
between 3 different models. (A, AF,F )
A
 model:      air onl
y, with built in sensor
AF model:   air & floo r , with both built in and remote sensor
F model:      floor only, with remote sensor
Press and hold button              for 5 seconds. Now you can see Menu 01, to proeceed to other menu, press button                  again. To exit menu, press button
First turn off the thermostat using the on/off button
Menu #
 01
Switching differential.
Calibrate the room temperature. This feature is used to compensate for any difference
Calibrate the floor temperature. This feature is used to compensate for any  difference
Set the floor temperature limit.
Select temperature format  
06
07
08
09
10
03
04
05
02
Feature Description
Factory Default
Feature Value
0
°C
40 
°C
4°C
10°C
35°C
2°C~ 7°C
10°C~ 20°C
20°C~ 35°C
20
°C ~ 
40 
°C
  
°C
 / 
°F
  
°C
A / AF / F A 
Press         or          to select
The numbers of degree difference before switching.
between the displayed room temperature  and a thermometer.  
between the displayed floor temperature  and a thermometer.  
This feature is to protect the floor surface.
 °C or °F. 
 The default is 1°C which means the thermostat will switch the 
heating on 
0.5°C below the set temperature and will turn it off 0.5°C above the set temperature. 
 
With a 2°C differential, 
the heating will switch on 1°C below the set temperature 
and will switch off 1°C above the set temperature.
 
1°C 1°C ~ 5°C
-5°C ~ +5°C
0
°C
-5°C ~ +5°C
Installation and Wiring
Carefully separate the front half of the thermostat from the back plate by placing a 
small flat head terminal driver into the slots on the bottom face of the thermostat. 
Carefully unplug the ribbon connector which is plugged in to the front half of the thermostat.
Place the thermostat front half somewhere safe. Make the wiring connections as 
Screw the thermostat back plate on to the back box.
shown in the diagram below.
Re-connect the thermostat ribbon cable and clip the 
CS-11 LCD Digital Setback Thermostat
Frost protection.  This is to avoid room temperature goes below 5°C.
The setback amount( the amount of temperature reduction)
on / off off
Switched live 
output 
230V ~ 50Hz 
L N 
Link terminals 1 
to 3 for 230VAC 
live output 
Remote sensor for floor 
temperature  control 
Timeswitch live 
for operaon 
of temperature 
setback mode 

Registered Address:  6 Tannery Yard, Witney Street, Burford, Oxon., OX18 4DW
Tel:  01993 824900 : www.emmeti.co.uk :  e:  [email protected]
This gives you the option to limit the minimum set temperature
This gives you the option to limit the maximum set temperature
                  
   
1. Please ensure that the electrical wiring of the installation and connections to and from the thermostat and any remote sensor connected to it are in accordance with BS 7671, the latest edition of the IET
    Wiring Regulations.
2. The thermostat must be wired to the electric mains through a switch capable of disconnecting all poles compliant with the current safety standards and with a contact separation of at least 3 mm in all poles.
3. Before commencing work on the installation, the electricity supply must be disconnected.
4. The depth of the back box should be 35mm minimum.
WARNING
Please Note: one of the following error messages will appear if one of these problems occur:
E0, meaning the internal sensor is broken, short-circuit or not working properly.
E1, meaning the floor sensor is broken, short-circuit, not connected, or not working properly.
Single   Zone
Multi    Zone
1
ErP Class
+1%
8
ErP Class
+5%
two halves together. 

• 
  AOC LC32D1320

  TV LC32D1320 Guide, #11JA1G

  LC32D1320, 142, aoc/lc32d1320.pdf

• 
  Lightolier Lighting Systems LSBW-15

  Indoor Furnishing Lighting Systems LSBW-15 Reference Book, #G64HE4

  Lighting Systems LSBW-15, 2, lightolier/lighting-systems-lsbw-15.pdf

• 
  Cerwin-Vega XLS SERIES

  User Guide (XLS SERIES, #CAO478)

  XLS SERIES, 8, cerwin-vega/xls-series.pdf

• 
  HiWatch DS-N204

  Document (DS-N204, #E5FK92)

  DS-N204, 25, hiwatch/ds-n204.pdf

• 
  Sena X1 PRO

  Sena User Guide: X1 PRO (#J82THL)

  X1 PRO, 86, sena/x1-pro.pdf

• 
  Power Acoustik PTID-7300

  Car Video System PTID-7300 Guidance, #65I4B4

  PTID-7300, 20, power-acoustik/ptid-7300.pdf

• 
  Zenith L20V26

  L20V26 TV - #P1971M

  L20V26, 44, zenith/l20v26.pdf

• 
  BT 1250 Classic

  BT Reference Book Cordless Telephone 1250 Classic (#WWH6S4)

  1250 Classic, 34, bt/1250-classic.pdf

• 
  York PT8-UH

  #F98M4H: PT8-UH User Guide

  PT8-UH, 8, york/pt8-uh.pdf

• 
  Atari 130XE

  Desktop 130XE Handbook, #Z7MH1J

  130XE, 50, atari/130xe.pdf

• Search YouTube Videos for emmeti CS-11 Device
• Search Google for emmeti CS-11 Information
• Search Photo of emmeti CS-11 in Google Images
• Search Twitter for emmeti CS-11 News