Data: UPD 11th November 2023
CHIEF SSB-301 Racks & Stands PDF Installation Instructions (Updated: Saturday 11th of November 2023 06:51:39 PM)
Rating: 4.5 (rated by 90 users)
Compatible devices: MSP-YM4, Kontour KRA234, PRO-2000 Series, QMP1MM2, MCM1U, MSP-TDKCG110, PWH MSP-SPWH, K1C100.
Recommended Documentation:
Text Version of CHIEF SSB-301 Racks & Stands Manual (Summary of Contents)
(Ocr-Read of Document's Main Page, UPD: 11 November 2023)
INSTALLATION INSTRUCTIONS
Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes
no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use
of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or
implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief Manufacturing, a products division of Milestone AV Technologies
6436 City West Parkway, Eden Prairie, MN 55344
• P: 800.582.6480 / 952.225.6000 • F:877.894.6918 / 952.894.6918
8800-002166 Rev01
©2012 Milestone AV Technologies,
a Duchossois Group Company
06/12
SSB-301, SSM-301, SLB-301 and SLM-301 Interface Brackets
SSB-301, SSM-301, SLB-301 and SLM-301 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the specific
installation instructions provided with the mount for additional installation information.
Unpack carton and verify kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative.
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
Installation Instructions
WARNING: OVER TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT over tighten screws when installing interface brackets.
NOTE: Step 1 is only required when installing an SLB/SSB interface bracket. If an SLM/SSM bracket is being installed, proceed to step 2.
1. Screw thumb screws onto 10-24 x 5/8" Phillips pan head screws. DO NOT fully tighten thumb screws at this time.
2. Turn projector upside down on a flat surface.
3. Place the nylon spacer onto bottom of the projector over threaded insert near center of projector.
4. Place the interface bracket onto the bottom of the projector, aligning the mounting hole near center of the bracket with the spacer and holes
in bracket side tabs with other threaded inserts in the bottom of the projector. Ensure that triangle in bracket points towards front of
projector.
5. Position M6 x 10mm mounting screws with M6 flat washers through four holes in bracket side tabs and into threaded inserts in bottom of
projector. Place the M6 x 20mm screw through the mounting hole near center of interface bracket, through nylon spacer and into the
threaded insert. Tighten all fasteners at this time, securing the bracket to the projector.
NOTE: Security screws can be substituted when mounting interface bracket to projector by using the parts and installation
instructions in the All-Points Security Kit.
Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.
(1) Interface Bracket (4) Screw, Phillips Pan Head, Machine, M6 x 10mm
(6) 10-24 Thumb Nuts ** (1) Screw, Phillips Flat Head, Machine, M6 x 20mm
(1) All-Points Security Kit (4) Washer, M6
(1) 5/32" Security Hex Key (1) Spacer, Nylon, 1/2" x .257" x 5/8"
**Only used when installing SLB/SSB interface brackets.
NOTE: Specific to SSB-style and SSM-style interface bracket installation: All appropriate screws come pre-installed in the circled locations above.
DO NOT attempt to substitute and USE ONLY this pre-installed hardware for SSB-style and SSM-style interface bracket installation.
Note: SSB-style interface bracket connections are circled. Note: SSM-style interface bracket connections are circled.
SLB-301
SLM-301
Towards front
of projector
Towards front
of projector
Recommended:
885, HW1800VD1V22-P, CSM 86300 G, PL- 30008
Firebox M4600, MA641, MAGHOLDER, Jolly line CWM-1737, AM-C330S, UCH006
-
Storage capacity and comfort come together in the new incorporation to the Nox series. With Nox Blaze adapter you can adapt two 2.5 SSD drives in a 5.25 internal bay in a simple and fast way, without wires or screws.Also, if you are someone who does not come off of the screen Nox ...
Model & Doc Type: BLAZE SWAP ADAPTER 2
-
2203 BALLATTA SHELVING UNITThank you for purchasing this Ballatta shelving unit. Please ensure instructions are read in full before attempting to assemble product.1Ref: 2507 / 2203This product is heavy, it should be assembled as near as possible to the point of use. Take care when lifti ...
Model & Doc Type: BALLATTA 2203 9
-
Telescoping pole extends upward from 17 inches to 29 inches.Compatibility: Fits smartphones with cases weighing up to 2 pounds and measuring up to 4” wide.IMPORTANT:Do not overtighten ring. Overtightening may damage threads on holder and also make it difficult to adjust phone and tabl ...
Model & Doc Type: CLAMPRCB 2
-
PD2253 (Page 1) 11/06®Wiring Device-KellemsHubbell Incorporated185 Plains RoadMilford, CT 06460-8897(203) 882-4800English FrançaisEspañolInstallaInstallaInstallaInstallaInstallation Instrtion Instrtion Instrtion Instrtion InstructionsuctionsuctionsuctionsuctionsDirectives de montageDi ...
Model & Doc Type: HBL6750 Series 3
Operating Impressions, Questions and Answers:
