SkyLink 18T4 Operation & User’s Manual

 1. INTRODUCTION
Skylink
®
 Four-Button
Keychain Transmitter
Model 18T4
In this package, you will find a four button keychain transmitter with 12V
alkaline battery and a mounting bracket.
 3. TROUBLE SHOOTING
Q: Door opener does not react after pressing the button on the transmitter ?
A: - Ensure when the button on the transmitter is pressed, the red light on the
transmitter comes on. Otherwise, check if the battery is inserted properly.
- The appropriate button on the transmitter should be pressed.
- If the red light on the receiver flashes when you press the button on
the transmitter, but the door opener does not respond, please ensure the
red/black wire is successfully connected from the receiver to the wall
mounted door control.
- Ensure the wires that are previously connected to the wall mounted
door control are not loose.
- Ensure the transmitter has been programmed to the receiver. Refer
to section 2 for how to program a transmitter to the receiver.
You need to do the programming in order to add the transmitter to the
receiver.
2. PROGRAM A TRANSMITTER TO THE RECEIVER
Four-Button
Keychain Transmitter
(Battery inside)
Learn
Button
Button A
Button B
Button C
Button D
There are 4 buttons on your transmitter, the other
button can be used to control another Skylink
®
 Garage
Door Receiver Model 18R (sold separately) or Skylink
®
Wireless Switch Receiver Model SW-18R (sold
separately).
6. ADDITIONAL RECEIVER
12 volt alkaline battery (size 23A)
(included).
It is time to change the battery
when the red LED on the trans-
mitter does not turn on when
either button is pressed.
5. BATTERY
Plug the receiver SW-18R or 18R (sold separately) into an electrical
socket.
Press and hold the learn button on the left hand side of the receiver.
The red LED on the receiver will flash.
Press the assigned button (either button A or B or C or D) of the
transmitter you want to program to the receiver.
The receiver red LED will go off indicates the programming is completed.
To program a transmitter to control another receiver, repeat process
(1) to (4) but pressing another button (A or B or C or D).
2
1
3
4
5
You can delete the transmitter from a receiver.
Unplug the receiver from the electrical socket.
Pr ess and hold the learn button on the left hand side of the receiver
when plugging the receiver into an electrical socket, the red LED on the
receiver will flash rapidly. All the transmitters and keypads are deleted.
4.  REMOVE TRANSMITTER FROM THE RECEIVER
If, within one year from date of purchase, this product should become defective
(except battery), due to faulty workmanship or materials, it will be repaired or
replaced, without charge. Proof of purchase and a Return Authorization are required.
8. WARRANTY
7. FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference
received, including interference that may cause undesired operation.
WARNING:
Changes or modifications to this unit not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
9. CUSTOMER SERVICE
If you would like to order Skylink’s products or have difficulty getting them to work,
please :
1. visit our FAQ website at www.skylinkhome.com , or
2. email us at [email protected], or
3. call our toll free at 1-800-304-1187 from Monday to Friday, 9 am to 5 pm EST.
Fax  +800 286-1320
2
1
Mounting
Bracket
CUSTOMER SERVICE
17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3
Email:[email protected]
http://www.skylinkhome.com
P/N. 101A292-001  Rev.1
©2004 SKYLINK GROUP

• 
  Skulpt AIM

  Fitness Electronics User Guide #2BZ137

  AIM, 16, skulpt/aim.pdf

• 
  DIR Parker 1090

  Indoor Furnishing Tutorial #1SDY44

  Parker 1090, 13, dir/parker-1090.pdf

• 
  Subaru 2004 Forester

  Automobile Reference Book #P4WB51

  2004 Forester, 15, subaru/2004-forester.pdf

• 
  Epson TM-T88V-DT

  #1FNWM4: TM-T88V-DT Document

  TM-T88V-DT, 28, epson/tm-t88v-dt.pdf

• 
  DNP CL-500

  Laminator CL-500 Guide, #XT3IZ5

  CL-500, 24, dnp/cl-500.pdf

• 
  Toshiba MW24F11

  Toshiba User Manual: MW24F11 (#94JESQ)

  MW24F11, 68, toshiba/mw24f11.pdf

• 
  ProtoMachines LED8

  ProtoMachines Instruction: LED8 (#NV5UE3)

  LED8, 2, protomachines/led8.pdf

• 
  Radyne DMD2401 IBS

  Radyne Document: DMD2401 IBS (#729X2F)

  DMD2401 IBS, 199, radyne/dmd2401-ibs.pdf

• 
  Samsung AQV18NSD

  Air Conditioner AQV18NSD Instruction, #B6UJO4

  AQV18NSD, 96, samsung/aqv18nsd.pdf

• 
  BT FREESTYLE 3500

  Instruction (FREESTYLE 3500, #1B282Y)

  FREESTYLE 3500, 72, bt/freestyle-3500.pdf

• Search YouTube Videos for SkyLink 18T4 Device
• Search Google for SkyLink 18T4 Information
• Search Photo of SkyLink 18T4 in Google Images
• Search Twitter for SkyLink 18T4 News